Submittal Sheet

ManualsBrandsZ-FLEX ManualsPlumbing Supplies3" Z-Vent Adjustable Roof Flashing

Z-Vent

Commercial Systems

Dimensional Data

October 2012

Summary of content (36 pages)

PAGE 1
® Z-Vent® Commercial Systems Dimensional Data October 2012
PAGE 2
PAGE 3
Z-VENT™ Table of Contents Commercial Systems Z-Vent Single Wall Z-Vent Double Wall Pipe 1 Double Wall Pipe 18 Boot Tee 2 Double Wall Boot Tee 19 Tee 2 Double Wall Tee 19 Tee Cap with Drain 3 Double Wall Tee Cap 20 Adjustable Pipe 3 Double Tee Cap with Drain 20 Vertical Drain Pipe 4 Double Wall Damper Pipe 21 Pipe with Inspection Port 4 Single Wall to Double Wall Adapter 22 Low Resistance Rain Cap 5 Double Wall to Single Wall Adapter 22 Rain Cap 5 Double Wall Rain Cap 2
PAGE 4
Z-VENT™ Single Wall AL 29-4C® Special Gas Vent Available in diameters 3in to 24in and standard lengths up to 10ft (3in and 4in diameter only). Pipe can be cut to length. The female end of each Z-VENT™ component incorporates a Double Fail Safe™ self sealing gasket. Examine all components to ensure that gasket integrity has remained during shipping. Gaskets must be in proper position or flue gases could leak resulting in carbon monoxide poisoning.
PAGE 5
Z-VENT™ Single Wall AL 29-4C® Special Gas Vent Boot Tee A B C D Part Number Description 3 11.00 7.50 4.88 2SVSTBT03 Z-Vent Boot Tee 3 in 4 12.00 8.00 5.25 2SVSTBT04 Z-Vent Boot Tee 4 in 5 14.00 9.50 7.00 2SVSTBT05 Z-Vent Boot Tee 5 in 6 17.00 11.25 10.00 2SVSTBT06 Z-Vent Boot Tee 6 in 7 13.63 12.50 11.25 2SVSTBT07 Z-Vent Boot Tee 7 in 8 20.34 13.75 12.50 2SVSTBT08 Z-Vent Boot Tee 8 in 9 22.30 15.00 13.75 2SVSTBT09 Z-Vent Boot Tee 9 in 10 24.44 16.25 15.
PAGE 6
Z-VENT™ Single Wall AL 29-4C® Special Gas Vent Tee Cap with Drain A tee cap with drain is required at the bottom of a vertical stack. High temperature silicone tubing is available separately.
PAGE 7
Z-VENT™ Single Wall AL 29-4C® Special Gas Vent Vertical Drain Pipe Used to drain condensate from the Vent system. High temperature Drain Tube kit sold separately. A B Part Number Description 3 5.75 2SVEVDP03 Vertical Drain Pipe 3" 4 5.75 2SVEVDP04 Vertical Drain Pipe 4" 5 5.75 2SVEVDP05 Vertical Drain Pipe 5" DRAIN FITTING B C ØA Pipe with Inspection Port Vent length with test port allows easy access for flue gas analysis.
PAGE 8
Z-VENT™ Single Wall AL 29-4C® Special Gas Vent Low Resistance Rain Cap A B C Part Number Description 5 7.00 11.00 2SVSRC05 Low Resistance Rain Cap 5in 6 7.00 12.75 2SVSRC06 Low Resistance Rain Cap 6in 7 7.30 14.00 2SVSRC07 Low Resistance Rain Cap 7in 8 7.50 15.00 2SVSRC08 Low Resistance Rain Cap 8in 9 8.00 18.50 2SVSRC09 Low Resistance Rain Cap 9in 10 8.00 18.50 2SVSRC10 Low Resistance Rain Cap 10in 12 9.00 22.12 2SVSRC12 Low Resistance Rain Cap 12in 14 10.00 25.
PAGE 9
Z-VENT™ Single Wall AL 29-4C® Special Gas Vent Exit Cone A B C Part Number Description Designed to increase stack velocity. Extremely low resistance. It is recommended to use tee cap with drain at base of stack. 6 4.87 9.25 2SVSXITC06 Z-Vent Exit Cone 6 in 7 5.69 9.88 2SVSXITC07 Z-Vent Exit Cone 7 in 8 6.50 10.40 2SVSXITC08 Z-Vent Exit Cone 8 in 9 7.31 10.88 2SVSXITC09 Z-Vent Exit Cone 9 in 10 8.125 11.25 2SVSXITC10 Z-Vent Exit Cone 10 in 12 9.88 12.
PAGE 10
Z-VENT™ Single Wall AL 29-4C® Special Gas Vent 45° Termination Elbow A Part Number Description 3 2SVSTEX0345 Z-Vent Termination Elbow 3 in X 45° 4 2SVSTEX0445 Z-Vent Termination Elbow 4 in X 45° 45° ØA 4.0 90° Termination Elbow ØA A Part Number Description 3 2SVSTEX0390 Z-Vent Termination Elbow 3 in X 90° 4 2SVSTEX0490 Z-Vent Termination Elbow 4 in X 90° 6.000 90° 5.0 Termination Hood C Part Number C A B Description 3 6.75 3.75 2SVSHTX03 Z-Vent Termination Hood 3 in 4 7.
PAGE 11
Z-VENT™ Single Wall AL 29-4C® Special Gas Vent 15° Elbows A B C Part Number Description 3 2.45 4.20 2SVEEWCF0315 Z-Vent Elbow 15° X 3 in 4 2.51 4.26 2SVEEWCF0415 Z-Vent Elbow 15° X 4 in 5 2.58 4.33 2SVEEWC0515 Z-Vent Elbow 15° X 5 in 6 2.64 4.39 2SVEE0615 Z-Vent Elbow 15° X 6 in 7 2.71 4.46 2SVEE0715 Z-Vent Elbow 15° X 7 in 8 2.78 4.53 2SVEE0815 Z-Vent Elbow 15° X 8 in 9 2.84 4.59 2SVEE0915 Z-Vent Elbow 15° X 9 in 10 2.91 4.
PAGE 12
Z-VENT™ Single Wall AL 29-4C® Special Gas Vent 45° Elbows A B C Part Number Description 3 1.62 3.37 2SVEEWCF0345 Z-Vent Elbow 45° X 3 in 4 1.83 3.58 2SVEEWCF0445 Z-Vent Elbow 45° X 4 in 5 4.16 5.91 2SVEEWC0545 Z-Vent Elbow 45° X 5 in 6 4.37 6.12 2SVEE0645 Z-Vent Elbow 45° X 6 in 7 4.58 6.33 2SVEE0745 Z-Vent Elbow 45° X 7 in 8 4.79 6.54 2SVEE0845 Z-Vent Elbow 45° X 8 in 9 5.00 6.75 2SVEE0945 Z-Vent Elbow 45° X 9 in 10 5.20 6.
PAGE 13
Z-VENT™ Single Wall AL 29-4C® Special Gas Vent Increaser B 4 5 5 6 8 6 7 8 9 6 7 8 9 7 8 9 10 8 9 10 12 10 12 14 10 12 12 14 16 14 16 18 16 18 20 18 20 22 20 22 24 22 24 24 C 7.00 8.15 7.00 8.15 10.30 7.00 8.15 9.20 10.30 7.00 8.15 9.20 10.30 7.00 8.15 9.20 10.30 7.00 8.15 9.20 11.36 8.15 10.30 12.43 7.00 9.20 8.15 11.30 13.43 9.15 11.30 13.43 9.15 11.30 13.43 9.15 11.30 13.43 9.15 11.30 13.43 9.15 11.30 9.
PAGE 14
Z-VENT™ Single Wall AL 29-4C® Special Gas Vent Eccentric Increaser Used to upsize a vent system. Recommended for use with horizontal vent runs. A B C D Part Number Description 5 5 5 6 6 6 6 6 7 7 7 8 8 8 9 9 10 10 10 12 12 12 14 14 14 16 16 16 18 18 18 20 20 22 6 7 8 7 8 9 10 12 8 10 12 10 12 14 10 12 12 14 16 14 16 18 16 18 20 18 20 22 20 22 24 22 24 24 12.00 12.00 14.00 12.00 12.00 14.00 14.00 14.00 12.00 12.00 14.00 12.00 12.00 14.00 12.00 12.00 12.00 13.00 14.00 15.00 15.00 15.00 15.00 15.
PAGE 15
Z-VENT™ Single Wall AL 29-4C® Special Gas Vent Flashing Flat A B C Part Number Description 3 12 12.50 2SVSSCF03 Z-Vent Flashing Flat 3 in 4 12 14.00 2SVSSCF04 Z-Vent Flashing Flat 4 in 5 12 16.00 2SVSF05 Z-Vent Flashing Flat 5 in 6 12 17.00 2SVSF06 Z-Vent Flashing Flat 6 in 7 12 18.50 2SVSF07 Z-Vent Flashing Flat 7 in 8 12 22.00 2SVSF08 Z-Vent Flashing Flat 8 in 9 12 22.00 2SVSF09 Z-Vent Flashing Flat 9 in 10 12 23.00 2SVSF10 Z-Vent Flashing Flat 10 in 12 12 26.
PAGE 16
Z-VENT™ Single Wall AL 29-4C® Special Gas Vent Wall Thimble A B C Part Number Description 3 5.00 10.00 2SVSWTF03 Z-Vent Wall Thimble 3 in 4 6.00 10.00 2SVSWTF04 Z-Vent Wall Thimble 4 in 5 7.00 12.00 2SVSWTF05 Z-Vent Wall Thimble 5 in 6 18.00 24.00 2SVSWTF06 Z-Vent Wall Thimble 6 in 7 19.00 24.00 2SVSWTF07 Z-Vent Wall Thimble 7 in 8 20.00 26.00 2SVSWTF08 Z-Vent Wall Thimble 8 in 9 21.00 26.00 2SVSWT09 Z-Vent Wall Thimble 9 in 10 22.00 28.
PAGE 17
Z-VENT™ Single Wall AL 29-4C® Special Gas Vent Guy Band A B Part Number Description 3 3.00 2SVSGB03 Z-Vent Guy Band 3 in 4 3.00 2SVSGB04 Z-Vent Guy Band 4 in 5 3.00 2SVSGB05 Z-Vent Guy Band 5 in 6 3.00 2SVSGB06 Z-Vent Guy Band 6 in 7 3.00 2SVSGB07 Z-Vent Guy Band 7 in 8 3.00 2SVSGB08 Z-Vent Guy Band 8 in 9 3.00 2SVSGB09 Z-Vent Guy Band 9 in 10 3.00 2SVSGB10 Z-Vent Guy Band 10 in 12 3.00 2SVSGB12 Z-Vent Guy Band 12 in 14 3.00 2SVSGB14 Z-Vent Guy Band 14 in 16 3.
PAGE 18
Z-VENT™ Single Wall AL 29-4C® Special Gas Vent Vent Support A B C Part Number Description 3 2.5 3 2SVSWS03 Z-Vent Single Wall Support 3in 4 3.0 3 2SVSWS04 Z-Vent Single Wall Support 4in 5 4.5 3 2SVSWS05 Z-Vent Single Wall Support 5in 6 5 3 2SVSWS06 Z-Vent Single Wall Support 6in 7 5.
PAGE 19
Z-VENT™ Single Wall AL 29-4C® Special Gas Vent Adapter 6in (Double Female) A B C Part Number 3 2.00 5.50 2SVSNA03.5 Z-Vent Appliance Adaptor 3 in 4 2.00 5.50 2SVSNA04.5 Z-Vent Appliance Adaptor 4 in 5 2.00 5.50 2SVSA05 Z-Vent Appliance Adaptor 5 in 6 2.00 5.50 2SVSA06 Z-Vent Appliance Adaptor 6 in 7 2.00 5.50 2SVSA07 Z-Vent Appliance Adaptor 7 in 8 2.00 5.50 2SVSA08 Z-Vent Appliance Adaptor 8 in 9 2.00 5.50 2SVSA09 Z-Vent Appliance Adaptor 9 in 10 2.00 5.
PAGE 20
Z-VENT™ Single Wall AL 29-4C® Special Gas Vent Roof Jack Support System NOTICE The Z-Vent™ Roof Jack Support System, shall be used on all through the roof terminations for single or double wall (14 inch through 24 inch) venting systems with combustible or non combustible roof structures. Prepare the breach location of the rood that will accept the Z-Vent™ Jack Support System, by drilling a small hole marking the center of the vent termination. Refer to the framing chart below for opening dimensions.
PAGE 21
Z-VENT™ Double Wall AL 29-4C® Special Gas Vent Double Wall Pipe B C Available in diameters 3in to 24in. The female end of each Z-VENT™ component incorporates a Double Fail Safe™ self sealing gasket. Examine all components to ensure that gasket integrity has remained during shipping. Gaskets must be in proper position or flue gases could leak resulting in carbon monoxide poisoning. The installation shall be in accordance with the manufacturer’s installation instructions.
PAGE 22
Z-VENT™ Double Wall AL 29-4C® Special Gas Vent Double Wall Boot Tee A B C D Part Number Description 3 11.00 7.50 4.88 2SVDTBT03 Z-Vent DW Boot Tee 3 in 4 12.00 8.00 5.25 2SVDTBT04 Z-Vent DW Boot Tee 4 in 5 14.00 9.50 7.00 2SVDTBT05 Z-Vent DW Boot Tee 5 in 6 17.00 11.25 10.00 2SVDTBT06 Z-Vent DW Boot Tee 6 in 7 13.63 12.50 11.25 2SVDTBT07 Z-Vent DW Boot Tee 7 in 8 20.34 13.75 12.50 2SVDTBT08 Z-Vent DW Boot Tee 8 in 9 22.30 15.00 13.
PAGE 23
Z-VENT™ Double Wall AL 29-4C® Special Gas Vent Double Wall Tee Cap A B C Part Number Description 5 2 4 2SVDTC05 Z-Vent DW Tee Cap 5 in 6 2 4 2SVDTC06 Z-Vent DW Tee Cap 6 in 7 2 4 2SVDTC07 Z-Vent DW Tee Cap 7 in 8 2 4 2SVDTC08 Z-Vent DW Tee Cap 8 in 9 2 4 2SVDTC09 Z-Vent DW Tee Cap 9 in 10 2 4 2SVDTC10 Z-Vent DW Tee Cap 10 in 12 2 4 2SVDTC12 Z-Vent DW Tee Cap 12 in 14 3 5 2SVDTC14 Z-Vent DW Tee Cap 14 in 16 3 5 2SVDTC16 Z-Vent DW Tee Cap 16 in 18 3 5 2SVDT
PAGE 24
Z-VENT™ Double Wall AL 29-4C® Special Gas Vent Double Wall Damper Pipe A Part Number Description 6 2SVDIDS06 Z-vent D/W Damper Pipe 6 in 7 2SVDIDS07 Z-vent D/W Damper Pipe 7 in 8 2SVDIDS08 Z-vent D/W Damper Pipe 8 in 9 2SVDIDS09 Z-vent D/W Damper Pipe 9 in 10 2SVDIDS10 Z-vent D/W Damper Pipe 10 in 12 2SVDIDS12 Z-vent D/W Damper Pipe 12 in Used to adjust flue gas flow in positive or negative pressure vent systems.
PAGE 25
Z-VENT™ Double Wall AL 29-4C® Special Gas Vent Single Wall to Double Wall Adapter A B Part Number 3 5.75 2SVDSA03 Z-Vent SW to DW Adaptor 3in 4 5.75 2SVDSA04 Z-Vent SW to DW Adaptor 4in 5 5.75 2SVDSA05 Z-Vent SW to DW Adaptor 5in 6 5.75 2SVDSS06 Z-Vent SW to DW Adaptor 6 in 7 5.75 2SVDSA07 Z-Vent SW to DW Adaptor 7in 8 5.75 2SVDSA08 Z-Vent SW to DW Adaptor 8in 9 5.75 2SVDSA09 Z-Vent SW to DW Adaptor 9in 10 5.75 2SVDSA10 Z-Vent SW to DW Adaptor 10in 12 5.
PAGE 26
Z-VENT™ Double Wall AL 29-4C® Special Gas Vent Double Wall Rain Cap A rain cap is designed to terminate a vertical stack and prevent the entrance of debris or rain into the vent. Includes wind band to prevent draft loss. A B C Part Number Description 3 6.00 11.00 2SVDRCF03 DW Rain Cap w/wind band 3in 4 6.00 12.75 2SVDRCF04 DW Rain Cap w/ wind band 4in 5 7.00 11.00 2SVDRCX05 DW Rain Cap w/wind band 5in 6 7.00 12.75 2SVDRCX06 DW Rain Cap w/wind band 6in 7 7.30 14.
PAGE 27
Z-VENT™ Double Wall AL 29-4C® Special Gas Vent 15° Double Wall Elbow A B C Part No 3 2.45 4.20 2SVDEWCF0315 Z-Vent DW Elbow 15° X 3 in 4 2.51 4.26 2SVDEWCF0415 Z-Vent DW Elbow 15° X 4 in 5 2.58 4.33 2SVDEWC0515 Z-Vent DW Elbow 15° X 5 in 6 2.64 4.39 2SVDE0615 Z-Vent DW Elbow 15° X 6 in 7 2.71 4.46 2SVDE0715 Z-Vent DW Elbow 15° X 7 in 8 2.78 4.53 2SVDE0815 Z-Vent DW Elbow 15° X 8 in 9 2.84 4.59 2SVDE0915 Z-Vent DW Elbow 15° X 9 in 10 2.91 4.
PAGE 28
Z-VENT™ Double Wall AL 29-4C® Special Gas Vent 45° Double Wall Elbow C 45° elbows are used when a direction change or offset is required. A B Part Number Description 3 1.62 3.37 2SVDE0345 Z-Vent DW Elbow 45° X 3 in 4 1.83 3.58 2SVDE0445 Z-Vent DW Elbow 45° X 4 in 5 4.16 5.91 2SVDE0545 Z-Vent DW Elbow 45° X 5 in 6 4.37 6.12 2SVDE0645 Z-Vent DW Elbow 45° X 6 in 7 4.58 6.33 2SVDE0745 Z-Vent DW Elbow 45° X 7 in 8 4.79 6.54 2SVDE0845 Z-Vent DW Elbow 45° X 8 in 9 5.00 6.
PAGE 29
Z-VENT™ Double Wall AL 29-4C® Special Gas Vent Double Wall Eccentric Increaser Used to upsize a vent system. Recommended for use with horizontal vent runs. A B C D Part Number Description 5 6 12.00 0.50 2SVDIE0506 Z-Vent DW Eccentric Increaser 5 to 6 in 5 7 12.00 1.00 2SVDIE0507 Z-Vent DW Eccentric Increaser 5 to 7in 5 8 14.00 2.00 2SVDIE0508 Z-Vent DW Eccentric Increaser 5 to 8 in 6 7 12.00 0.50 2SVDIE0607 Z-Vent DW Eccentric Increaser 6 to 7 in 6 8 12.00 1.
PAGE 30
Z-VENT™ Double Wall AL 29-4C® Special Gas Vent Double Wall Increaser A B C 3 3 4 4 4 5 5 5 5 5 5 5 5 6 6 6 6 7 7 7 7 8 8 8 9 9 10 10 10 12 12 12 14 14 14 16 16 16 18 18 18 20 20 22 4 5 5 6 8 6 7 8 9 6 7 8 9 7 8 9 10 8 9 10 12 10 12 14 10 12 12 14 16 14 16 18 16 18 20 18 20 22 20 22 24 22 24 24 7.00 8.15 7.00 8.15 10.30 7.00 8.15 9.20 10.30 7.00 8.15 9.20 10.30 7.00 8.15 9.20 10.30 7.00 8.15 9.20 11.36 8.15 10.30 12.43 7.00 9.20 8.15 11.30 13.43 9.15 11.30 13.43 9.15 11.30 13.43 9.15 11.30 13.43 9.
PAGE 31
Z-VENT™ Double Wall AL 29-4C® Special Gas Vent Double Wall Base Support A B Part Number Description 5 10.00 2SVDBS03 Z-Vent DW Base Support 3 in 6 11.00 2SVDBS04 Z-Vent DW Base Support 4 in 7 12.00 2SVDBS05 Z-Vent DW Base Support 5 in 8 13.00 2SVDBS06 Z-Vent DW Base Support 6 in 9 14.00 2SVDBS07 Z-Vent DW Base Support 7 in 10 15.00 2SVDBS08 Z-Vent DW Base Support 8 in 12 17.00 2SVDBS09 Z-Vent DW Base Support 10 in 14 19.00 2SVDBS10 Z-Vent DW Base Support 12 in 16 21.
PAGE 32
Z-VENT™ Double Wall AL 29-4C® Special Gas Vent Double Wall Storm Collar / Top Support A B Part ID Description 5 9.00 2SVDLS03 Z-Vent DW Storm Collar 3 in 6 10.00 2SVDLS04 Z-Vent DW Storm Collar 4 in 7 11.00 2SVDLS05 Z-Vent DW Storm Collar 5 in 8 12.00 2SVDLS06 Z-Vent DW Storm Collar 6 in 9 13.00 2SVDLS07 Z-Vent DW Storm Collar 7 in 10 14.00 2SVDLS08 Z-Vent DW Storm Collar 8 in 11 15.00 2SVDLS09 Z-Vent DW Storm Collar 9 in 12 16.
PAGE 33
Z-VENT™ Double Wall AL 29-4C® Special Gas Vent Double Wall Adjustable Length The use of adjustable pipe may be required when the system must be located within extremely tight installation parameters. IMPORTANT: Adjustable pipe can only be used with an adjacent pipe. Not to be inserted into fittings. A B C Part Number Description 3 6.00 9.50 2SVDPA03 Z-vent D/W Adjustable Pipe 3 in 4 6.00 9.50 2SVDPA04 Z-vent D/W Adjustable Pipe 4 in 5 9.00 15.
PAGE 34
Z-VENT™ Warranty The installation must conform to the requirements of the appliance manufacturers’ instructions, The National Fuel Gas Code and local codes and regulations. Z-FLEX® LIMITED LIFETIME WARRANTY Z-FLEX® (“Seller”) extends the following LIMITED WARRANTY for Z-VENT™ (the “Z-VENT™”): Seller warrants that at the time of purchase, the Z-VENT™ will be free of manufacturers defects in material and/or workmanship.
PAGE 35
PAGE 36
® 20 Commerce Park North Bedford, New Hampshire 03110-6911 tel: 603.669.5136 fax: 603.669.0309 452 Attwell Drive Etobicoke, ON M9W 5C3 tel: 416.679.0045 fax: 416.679.0051 www.z-flex.com email sales@z-flex.