F 275 325 225 180 Smoke Shut Down 375 High Cycle OFF Power ON www.zgrills.com WOOD PELLET GRILL ZPG - 450A OWNER’S MANUAL 1-785-317-5170 EMAIL:support@zgrills.com WEBSITE:www.zgrills.
CONTENTS WARNINGS 3 COMPOENT LIST 4 ASSEMBLY INSTRUCTIONS 5 INITIAL FIRING INSTRUCTIONS 12 SUBSEQUENT START-UP 13 OPERATING TIPS 15 MAINTENANCE & CLEANING 16 TROUBLESHOOTING 18 DIGTAL THERMOSTAT CONTROL WIRING DIAGRAM 20 Z GRILLS SUPPORT 21 3-Y LIMITED WARRANTY 22 1
WARNINGS! This grill is for outdoor use only. Do not use it in any enclosed area. Do not store or use combustible materials or liquids near this appliance. Keep young children away while it is in use. Maintain a long safe distance between your grill and any combustible. Do not move your grill while operating or while it is hot until the grill is completely cold. If a grease fire occurs, turn “off” and leave lid closed until the fire extinguished. Do not unplug the power cord. Do not throw water on it.
ASSEMBLY INSTRUCTIONS COMPONENT LIST ITEM QTY 1 2 2 2 3 1 4 1 5 1 6 1 7 1 8 1 9 1 10 1 11 1 12 1 13 1 14 1 15 1 16 1 17 1 18 1 19 1 20 2 21 2 22 1 23 1 24 1 25 2 26 1 27 2 28 1 29 1 30 1 31 1 4 DESCRIPTION Hinge Assy Pivot Fan Lid Name Plate Lid Handle Grill Chamber Assembly Hopper Assembly Chimney Cap Assembly Smoke Stack Assembly Smoke Stack Gasket RTD Foot Pad Front Flat Plate Left Bracket Hot Rod(Ignitor) Feeder Assembly Front Flat Plate Right Bracket Front Flat Plate Grease Basket Leg Leg Lateral F
1). Turn the grill body over, attach the Leg with Wheels(25) to the chamber by using Bolt(B), Spring Washers(E), Flat Gasket(J) orderly. Using screwdriver to tighten them. BODY FRAME ASSEMBLY: 1). Attach 2pcs Leg(20)(21) to Right and Left Lateral Leg(29)(28) with Bolt(B), Spring Washers(E), Flat Gasket(J) orderly. 2). Attach Axle(27) go through the holes of Wheels(25) and Right Lateral Leg(28), then install the Flat Washer on the inside, finally install the Cap Nuts(M) and tighten with a wrench.
INSTALLING CHAMBER HANDLE TO LID: ATTACHING THE SMOKESTACK AND CHIMNEY CAP: 1)Keep the Lid(4) open, attach Bolt(A) through Gasket(G), then installing handle(6) to Lid(4). Repeat the above steps on the other side. 2)Using wrench to tighten them.(Do not over tighten these Bolts) 1)Using bolt (A) through the holes of Smokestack(10) and the holes of Smokestack Insulation Cotton(11), attaching two bolts(A) to the hole of Grill body, then attaching Gasket(G) and nuts(H) , using wrench to tighten them.
ATTACHING HEAT BAFFLE: ATTACHING COOKING GRATE AND WARMING RACK: Attaching the Porcelain cooking grate(32) and warming rack(33) in the chamber, as shown. Attaching the Heat Baffle(30) on the Fire Pot, as shown. POSITIONING THE GREASE DRAIN PAN: Locate the Grease Drain Pan(31) on the pan support inside the Chamber(7). 10 HANG ON THE GREASE BASKET: Locate the Grease Drain Tube which is on the right side of the chamber, then hang the Grease Basket(19) on the hook. As shown.
INITIAL FIRING INSTRUCTIONS SUBSEQUENT START-UP Please take attention: If the grill fails to light or the fire in the Firepot goes Please read this manual carefully and follow it step by step before starting your Z Grills for the first time and each time the grill runs out of pellets. 1.Remove the Porcelain Grills, Grease Drain Pan and Heat Baffle from the interior of the grill. 2.Open the Pellet Hopper Lid, make sure there are no foreign objects in the Auger and Hopper. 3.
OPERATING TIPS 8.Turn on the grill and turn the Temperature Dial to any setting desired. With the lid closed, preheat the grill for 10 minutes before placing food. 1.Just like other barbecues, the actual temperature of this grill or the cooking times will be affected by external temperature, humidity, wind conditions, quality of pellets and so on. 2.Controller Operation 2.
MAINTENANCE & CLEANING Your Z Grills also needs your maintenance. Make sure your grill is OFF and cold completely before performing any maintenance and cleaning. Grease: With long-term use, it caused the accumulation of grease on the Flue Lining, the Grease Drain Tube, the V-shaped Grease Drain and the Grease Drain Pan. Always be sure these grease catch area is clean and free of debris. You should check and clean these area periodically to reduce the risk of fire.
TROUBLESHOOTING CAUTION: Make sure the grill is completely cool and unplugged before you do any inspection, cleaning, maintenance or service work. Problem Potential Cause Power Fuse Solution Make sure the power cord is plugged in. Verify there is power at the electrical outlet. Unexpected grill temperature is displayed External Factor Grill temperature is influenced by environmental factors such as high temperature, wind and direct sun. Place unit in shaded area.
DIGTAL THERMOSTAT CONTROL WIRING DIAGRAM RTD SENSOR Z GRILLS SUPPORT Thank you for shopping with us! If you have any question, feel free to contact us or your dealer. Z GRILLS INC. will offer the best technical and sales support in the industry.
Z GRILLS 3 YEARS LIMITED WARRANTY Z Grills Inc guarantees a 3 years warranty of our products from the date of purchase by the original owner against defects in all materials and workman-ship. During the warranty period, Z Grills Inc will at its option repair or replace the defective parts. This limited warranty does not apply to paint, burn pot, grill cover or damage caused from corrosion. Z Grills shall not be liable for transportation charges, labor costs or export duties.
