WOOD PELLET GRILL ZPG - 550B OWNER’S MANUAL 1-833-947-4557 EMAIL:support@zgrills.com WEBSITE:www.zgrills.
CONTENTS WARNINGS 3 COMPONENT LIST 4 ASSEMBLY INSTRUCTIONS 5 INITIAL FIRING INSTRUCTIONS 11 SUBSEQUENT START-UP 12 OPERATING TIPS 14 MAINTENANCE & CLEANING 15 TROUBLESHOOTING 16 DIGTAL THERMOSTAT CONTROL WIRING DIAGRAM 18 Z GRILLS SUPPORT 19 3-YEAR LIMITED WARRANTY 20 1
WARNINGS! This grill is for outdoor use only. DO NOT use it in any enclosed area. DO NOT store or use combustible materials or liquids near this appliance. Keep children away while it is in use. Maintain a safe distance between your grill and any combustible materials. DO NOT move your grill while operating or while it is hot. Wait until the grill is completely cold. If a grease fire occurs, turn “off” and leave lid closed until the fire is extinguished. Do not unplug the power cord.
ASSEMBLY INSTRUCTIONS COMPONENT LIST ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 4 Qty 1 1 1 1 1 1 1 1 1 2 1 2 1 1 1 1 1 2 2 1 1 4 1 1 Description Grill Chamber Assembly Hopper Assembly Warming Rack Porcelain Grills Grease Drain Pan Heat Baffle RTD Temperature Probe RTD Guard Lid Handle Handle Guide Lid Hinge Assembly Chimney Cap Smoke Stack Assembly Smoke Stack Gasket Grease Bucket Right Leg Wheels Axle Bottom Plate Left Leg Pipe Plug Hopper Lid Hopper Shell ITEM 25 26 27 28 2
3.) Push the Axle(19) through the wheel and then through the hole in the legs as shown. The Flat Washer(E), Spring Washer(F), and Cap Nut(G) are used to secure the wheel assembly in place. Repeat for the other wheel. Press the Wheel Caps(38) firmly into the outer recess on the wheels as shown. 1. MOUNTING THE BODY FRAME TO THE CHAMBER 1.) Unpack all the items, including the parts packed in the Grill Chamber(1).
2.INSTALLING THE CHAMBER HANDLE TO THE LID 4.INSTALLING THE HEAT BAFFLE 1.) Lift the Grill Assembly, turn, and place on the floor. 2.) From the inside of the raised lid, push the Blots(H) through the Washers(D) and then through the lid and Handle Guide(10). Handle should sit inside the depression in the guide. Thread Bolts(H) into Handle(9) and tighten with Wrench(B). 1.) Place the lower bracket of the Heat Baffle(6) into the groove of the feeder. As shown. 3.
6.INSTALLING THE COOKING GRATE AND WARMING RACK 1.) Install the Porcelain Cooking Grate(4) and Warming Rack(3) into the Chamber. As shown. INITIAL FIRING INSTRUCTIONS Please read this manual carefully and follow it step by step before starting your Z Grills for the first time and each time the grill runs out of pellets. 7.HANG ON THE GREASE BUCKET 1.) Locate the Grease Drain Tube which is on the right side of the Chamber, then hang the Grease Bucket(16) on the hook. As shown. 1.
SUBSEQUENT START-UP ATTENTION: If the grill fails to light or the fire in the Firepot goes out while cooking, it is vital to follow these steps when sufficient pellets are still in the Pellet Hopper. Failure to follow the steps may cause a hazardous “over-firing” of your grill due to an excess of unburned pellets in the Firepot. 1.Turn OFF the appliance and unplug the Power Cord. After the grill cools down, remove all food, the Porcelain Grills, Grease Drain Pan and the Heat Baffle. 2.
OPERATING TIPS MAINTENANCE & CLEANING 1. Like all grills, the actual temperature of this grill and the cooking times will be affected by external temperature, humidity, wind conditions, quality of pellets, etc. Your Z GRILL requires regular maintenance. 2. It is beneficial to shelter you grill from the wind. This will aid in temperature output, heat retention and heat recovery time when the lid is open.
TROUBLESHOOTING CAUTION: Make sure the grill is completely cool and unplugged before you do any inspection, cleaning, maintenance or service work. Problem Potential Cause Power Fuse Grill does not work properly Hot Rod Solution Fire goes out How to start 16 External Factor Excess or discolored smoke Pellets Replace moist pellets with fresh dry pellets. Make sure the power cord is plugged in. Verify there is power at the electrical outlet. Remove the digital control, check the fuse on back.
DIGITAL THERMOSTAT CONTROL WIRING DIAGRAM RTD SENSOR Z GRILLS SUPPORT Thank you for purchasing a Z GRILL! If you have any questions, please contact customer support or your Z GRILL dealer. Z GRILLS, INC.
Z GRILLS 3 YEAR LIMITED WARRANTY Z GRILLS, Inc. provides a 3 years warranty from the date of purchase by the original owner. This warranty applies to defects in all materials and workmanship. During the warranty period, Z GRILLS, Inc. will at its option repair or replace defective parts or units. This limited warranty does not apply to paint, firepot, grill cover or damage caused from corrosion. Z Grills shall not be liable for transportation charges, labor costs or export duties.