Installation Sheet

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE
WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR
THE CIRCUIT BREAKER IS SHUT OFF. GENERAL You don’t need
special tools to install this fixture. Be sure to follow the steps in the order
given. Under no circumstances should a fixture be hung on house
electrical wires, nor should a swag type fixture be installed on a ceiling
which contains a radiant type heating system. Read instructions
carefully. If you are unclear as to how to proceed, consult a qualified
electrician. NOTE: Proper wiring is essential for the safe operation of
this fixture.
GENERAL
You don’t need special tools to install this fixture. Be sure to
follow the steps in the order given. Under no circumstances
should a fixture be hung on house electrical wires, nor should a
swag type fixture be installed on a ceiling, which contains a
radiant type heating system. Read instructions carefully. If you
are unclear as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this
fixture.
FIXTURE ASSEMBLY
Carefully removed the fixture from the carton and check that all
parts are included as shown in figure. Be careful not to misplace
any of the screws or parts, which are needed to install this
fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP1: Secure universal mounting plate(G) onto outlet box with
box screw(H). For longer mounting plates additional securing may
be achieved by securing the mounting plate through the wall to
the building structure.
Proceed to connect wires:
GROUNDING INSTRUCTIONSSTEP 1: Insert the green
grounding screw into the hole with two raised dimples on the
circular strap. Wrap the ground wire from the fixture (if supplied)
around the green grounding screw, then connect it to ground wire
from the outlet box (if not fixed on the outlet box) using a wire
connector (not supplied). If ground wire from the fixture is not
supplied, wrap the ground wire (if not fixed on the outlet box) from
the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and connect the
wires according to the directions below:
*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer
wire is square shaped or ridged and the less tracer wire is
round in shape or smooth (seen best when viewed from wire
end.)
STEP 3: Take your fixture wire(s) from group A and place
evenly against the black wire from the outlet box. Do NOT twist
wires together before using wire connectors.
STEP 4: Fit a wire connector (not supplied) over the wires and
screw the connector clockwise until you feel a firmness.
STEP 5: Try gently to pull the connector off the wires. If you can
pull the connector off, carefully re-do steps 3 and 4, as above,
and check again for a firm connection
STEP 6: Connect the fixture wire from group B to the white wire
from the outlet box in the same manner
FINAL ASSEMBLY
STEP1: After wires are connected, tuck them carefully inside
outlet box.
STEP2: securing the back plate (E) to the mounting plate (G) with
screws(F).
STEP3: Install the bulb (D) (NOT INCLUDED) on the socket (B)
STEP4: Put the Ring (I) and Glass shade (A) on the Bracket (C).
CLEANING
To clean wipe fixture with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to
order replacement parts. All parts for this fixture can be ordered
from place of purchase. Be sure to use exact wording from
illustration when ordering parts.
Line art shown may not exactly match the fixture enclosed.
However, the installations do apply to this fixture.
ITEM NO: 3032-1V, 3032-2V, 3032-3V, 3032-4V, 3032-5V
GROUP A: Connect to Black
House Wire
GROUP B: Connect to Whi te
House Wire
BLACK
WHITE
*PARALLEL W I R E ( round &
smooth)
*PARALLEL W I R E ( square &
ridged)
WHITE OR GREY WITH
TRACER
WHITE OR G R E Y
W I T H O U T TRACER
BROWN G O L D OR
B L A C K WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER