Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY WARNING
BE SURE THE ELECTRICITY TO THE WIRES YOU ARE
WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED
OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow
the steps in the order given. Under no circumstances should a
fixture be hung on house electrical wires, nor should a swag type
fixture be installed on a ceiling, which contains a radiant type
heating system. Read instructions carefully. If you are unclear as to
how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this
fixture.
FIXTURE ASSEMBLY
Carefully removed the fixture from the carton and check that all
parts are included as shown in figure. Be careful not to misplace
any of the screws or parts, which are needed to install this fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP 1 - Attach Fixture Loop Assembly to
Fixture Body
A. Thread Fixture Loop Assembly (I) onto .
Hand tighten until snug.
STEP 2 - Attach Crossbar to Outlet Box
A. Secure the Corssbar (A) to the outlet box with outlet
box screws (not supplied). Tighten until snug..
STEP 3 Attach Nipple to Crossbar -
A. Thread one Hex Nut (D) onto the top end of the Nipple
(B).
B. Place one Lock Washer (C) over the top end of the
Nipple (B) and then thread the Nipple (B) into the center
lock hole of the Crossbar (A).
C. Using pliers, thread the hex Nut (D) against the
Crossbar (A) and hand tighten until snug.
STEP 4 - Attach Canopy Chain Loop to Nipple
A. Thread another Hex Nut (D) onto the end of the Nipple
(B).
B. Place the Lock Washer (C) over the end of the Nipple
(B) and then thread the Canopy Chain Loop (E) onto the
end of the Nipple (B).
C. Using pliers, thread the Hex Nut (D) against the
Canopy Chain Loop (E) and hand tighten until snug.
STEP 5 Assemble Ceiling Canopy -
A. Push the Ceiling Canopy (H) upward over the Outlet
Box. Thread the Canopy Lock Ring (F) onto the Canopy
Chain Loop (E) and tighten until snug to secure the
Ceiling Canopy (H).
STEP 6 - Attach Fixture Chain to Canopy
Chain Loop and Fixture Loop
A. Adjust the Fixture Chain (G) to your desired length by
removing the links if needed. You may need to use plier
to open the chain links. If so, put a cloth over the chain
to protect the finish from the pliers.
B. Attach one end of the Fixture Chain (G) onto the
Canopy Chain Loop (E) with one Quick Link (L) and
then attach the other end of the Fixture Chain (G) onto
the Fixture Loop on the top of the fixture with another
Quick Link (L).
STEP 7 Pass Supply Wires through Fixture
Chain
A. Pull the Supply Wires and Ground Wire up through the
Fixture Chain (G) alternating links. Push the wires up
through the Canopy Chain Loop (E) into the outlet box.You
fixture is now assembled and ready to use.
STEP 8 Make Wire Connections
A. Un-thread the Canopy Lock Ring (F) and slide Canopy Lock
Ring (F) and Ceiling Canopy (H) down the Fixture Chain (G)
B. Push all slack fixture wire through Canopy Chain Loop (E)
into Outlet Box. Trim excess fixture wire leaving a minimum
of 6 inch. Hanging out of the Outlet Box.
C. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.)
Twist connectors until wires are tightly joined together. Wrap
each connection with approved electrical tape and carefully
stuff all the connected wires into outlet box.
Note: If the electrical wire is going to be cut shorter than
provided you will need to identify the "L" line wire and the "N"
neutral wire before you cut the excess wire off. One is
labeled N and the other labeled L. To do this separate the "L"
line wire and the "N" neutral wire as far as you need to. Relabel the
wire near where you want to make the cut. Be sure
to mark the wire on the side of the fixture and not on the
excess wire being cut and removed.
D. Re-attach the Ceiling Canopy (H) as shown in Step 5.
attach the Ceiling Canopy (H) as shown in Step 5.
STEP 9 - Install Bulb
A. standard bulb with a candelabra screw
base Maximum 6 watts.
B. Place the bulb from the bottom of the glass frame. Insert
bulb and screw snugly into place.
Your fixture is now assembled and ready to use.
Enjoy!
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or
powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered
from place of purchase. Be sure to use exact wording
from illustration when ordering parts.
Line art shown may not exactly match the fixture enclosed.
However, the installations do apply to this fixture.
ITEM NO: 580CHM / 580CHB