USER MANUAL INTELLIGENT DISPLAY SERIES (IDS) PANELS Rugged Displays with Real Time Enhanced Video Z Microsystems, Inc. Z Microsystems, Inc. · 9820 Summers Ridge Road, San Diego, CA 92121 · T: 858.831.7000 · F: 858.831.7001 · www.zmicro.
REGULATORY FCC Information WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED AC PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS ALL THREE PRONGS CAN BE FULLY INSERTED 1. Use the power and video cables supplied with the product to help prevent interference with radio and television reception. The use of cables and adapters may cause interference with electronic equipment in the vicinity of this unit. 2.
TABLE OF CONTENTS Table of Contents Section Page 1.0 Product Overview............................................................................................................................................................ 4 1.1 About This Manual.............................................................................................................................................. 4 1.2 Product Overview...............................................................................................
PRODUCT OVERVIEW 1.0 PRODUCT OVERVIEW 1.1 About This Manual This product manual will help you through the installation and setup processes of your Intelligent Display Series (IDS) LCD panel. We recommend you read this manual carefully and follow the instructions in the installation chapter for verification of system functions and control settings. This manual is also available on the Z Microsystems website at www.zmicro.com.
PRODUCT OVERVIEW 1.2 Product Description Z Microsystems Intelligent Display Series (IDS) flat panel displays are engineered with unique flexible mounting options, an ultra-high per formance modular video processor, and touch panel options built into a rugged lightweight protective housing. The thin, lightweight IDS panels are available in 24”, 21.3”, and 17” sizes.
INSTALLATION 2.0 INSTALLATION NOTE: For the fastest and easiest installation of the IDS, follow these steps in the sequence they This section will provide information and assistance with the following topics: • Mounting & Hardware WARNING: Using assembly hardware that does not match specifications may damage • GCS Schematics for 17”, 21”, 24” internal components. • Installation Procedure Preparations In preparation to install the IDS, turn off the electrical power to your computer. are presented.
INSTALLATION 2.1.2 Schematic FOR IDS21 - Static Mount 21.3" IDS 4X 01-92381 4X 01-92619 HINGED SIDE HANDLE SIDE 4X 01-91869 21.
INSTALLATION 2.1.
INSTALLATION 2.2 Installation Walkthrough Installation Instructions for Static and Hinged Mounting Systems NOTE: Refer to the schematics on the previous pages for your respective display size for visual affirmation and mounting rail orientation. WARNING: Max Screw Depth 3/8” Hardware exceeding max screw depth could damage the display. 2.2.
CONNECTIONS & SETUP 3.0 CONNECTIONS & SETUP This section will provide information and assistance with the following topics: • Cable connections for power and video input connector but will no longer support analog signals as offered by the onboard video • Setting up touch panel functionality with the display • Software and Driver information for touch panel use Preparations In preparation to setting up and connecting the IDS, turn off the electrical power to your computer.
CONNECTIONS & SETUP 3.2 Touch Panel Setup Preparations In preparation to setting up the touch panel functionality on the IDS, turn off the electrical power to your computer. Required Software & Drivers • FTDI RS232-USB Bridge Driver NOTE: If the touch screen option has been purchased for the IDS, the touch screen manufacturer’s software must first be installed on the computer being used with the IDS.
CONNECTIONS & SETUP Setup Process for Touch Panel (Continued) Step 3 - Install and Setting the TSHARC Touch Panel Driver COM port Select Microchip, TSHARC-X/X, Serial Option and the respective Port COM setting. Once complete, Click on the Install button. Upon successful installation of driver, reboot computer if necessary. If the touch panel is not responding, open the ‘Universal Pointer Device Driver (UPDD)’ Control Panel and update the COM port setting.
CONNECTIONS & SETUP Setup Process for Touch Panel (Continued) User may also need to calibrate the touch screen panel using the calibration resource specific to their respective operating system (i.e. Windows, Linux, Mac) Continuous Touch Panel Sensing Option Some users may require continuous touch panel sensing. The Default settings for the UPDD driver are set to use lift-off packets that prevent sustained press and sensing.
OPERATIONS 4.0 Operations This section will provide information and assistance with the following topics: • Front Display Controls • Navigating the On-Screen Menus • Menu Configuration and Settings 4.1 Front Display Controls Push Button Controls The IDS features push-button controls on the lower front bezel of the monitor casing. These buttons provide easy access to the On-Screen Display (OSD) allowing the user to navigate and adjust image settings.
OPERATIONS 4.2 On-Screen Menus NOTE: The control buttons allow the user to 4.2.1 Main Menu control backlight operations; to store settings, and to revert to factory-saved settings. MAIN MENU R. 52 To access the On-Screen Display main menu, press the menu button on the front of the panel. All IDS functions are controlled using the Main Menu’s subtopics. PICTURE ADJUST GRAPHIC MODE These submenus can be accessed for adjustments and information via the display keys on the bottom panel of the display.
OPERATIONS 4.2.5 Configuration Screen CONFIGURATION MAIN MENU TIMEOUT 0 100 fACTORY SETTINGS CHANNEL 1 T YPE: ANALOG CHANNEL 2 T YPE: ANALOG CHANNEL SELECT: CHANNEL 2 SCALE MODE: NORMAL Menu Timeout: This is the amount of time the menu will remain displayed before it times out and exits automatically. When the menu times out, it disappears from the main screen. Reset Default Settings: Resets all Main Menu settings to the factory default settings.
TROUBLESHOOTING 5.0 TROUBLESHOOTING THE IDS SERIES 5.1 Troubleshooting Topics This section will provide information and assistance with the following topics: • Troubleshooting Topics for the IDS Series • Frequently Asked Questions about the IDS Series No Main Display Image If the cable from the computer to the display is secure, determine the color of the standby LED and follow the appropriate procedure below.
TROUBLESHOOTING Display Image Appears Fuzzy / Poor Quality (Analog Signal Issue) Possible Recovery: If the main image begins to appear fuzzy or “noisy”, adjust the “Horz Fine” until it is reduced. The “Horz Fine” option adjusts the phase of the video sampling clock. To access the “Horz Fine” submenu from the Main Menu, use the ‘+’ and ‘-’ arrow buttons to highlight the “Graphics Mode” option. Press the “Menu” button to access the “Graphics Mode” submenu.
FREQUENTLY ASKED QUESTIONS Touch Screen Not Responding Accurately The Touch Screen may require calibration from time to time. There are two forms of calibration, one is the touch panel controller in the UPDD control panel as discussed in the Touch Panel Setup installation guide. Another method is direct contact with the display through a utility built into the operating system on your host computer.
CUSTOMER SUPPORT 6.0 CUSTOMER SUPPORT NOTE: For image problems, run AUTO SETUP NOTE: If possible, stay by the computer. NOTE: More help, late-breaking news, and again before consulting this section. In most The Z Microsystems Technical Support details of the latest accesories for these cases, AUTO SETUP can fix the problem. See Representative may wish to go through the products may be found on the worldwide web at Auto Setup section for details problem over the telephone. www.zmicro.
MAINTENANCE & REPLACEMENT 7.0 MAINTAINING THE IDS DISPLAY SERIES Cleaning the Monitor Unplug the monitor from the power outlet before cleaning. • The IDS Displays are constructed with either an optically bonded resistive touch screen or optically bonded Anti Reflective (AR) shield. When cleaning the screen surface, a clean, lint-free cloth must be used. Isopropyl alcohol or monitor glass cleaner may be used to clean finger prints or smudges on the monitor’s screen.
APPENDIX 9.0 APPENDIX This section will provide information and assistance with the following topics: • Technical and Operational Standards for the IDS displays • Technical Schematics for the IDS displays • Engineering Drawings for the IDS displays 9.1.1 TECHNICAL SPECIFICATIONS FOR IDS 17” The IDS Display series is meticulously engineered to be adaptable and suited for an array of field operation, as well as being designed to support a wide selection of resolutions.
APPENDIX 9.1.2 SCHEMATIC OUTLINE FOR IDS 17” 4 3 2 1 REVISIONS REV DESCRIPTION DATE PREP APVD 01 ENGINEERING PROTOTYPE -- -- -- 12.02 D .25 14.68 .97 .80 4X 10-32 1.01 13.08 .145 4X 10-32 MODEL/SERIAL LABEL .264 C 8.35 9.686 3.937 4.040 2.86 1.165 8 7 5.370 3.937 6 5 B 1.01 .400 13.877 2.22 USB HOST DVI-I 1 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES TOLERANCES ARE: DECIMALS FRACTIONS XX = .01 1/32 XXX = .
APPENDIX 9.2.1 TECHNICAL SPECIFICATIONS FOR IDS 21” The IDS Display series is meticulously engineered to be adaptable and suited for an array of field operation, as well as being designed to support a wide selection of resolutions. The specifications unique to each particular LCD can vary. These particular specifications are available through our sales department. Environmental LCD Panel 21.
APPENDIX 9.2.2 SCHEMATIC OUTLINE FOR IDS 21” 4X 1/4-2 MODEL/SE LABEL C 4 3 2 1 REVISIONS 14.20 REV DESCRIPTION DATE PREP APVD 01 ENGINEERING PROTOTYPE -- -- -- D B . .25 18.45 4X 1/4-28 .232 .80 1.26 16.85 4X 10-32 1.03 .296 MODEL/SERIAL LABEL C 10.24 A 13.29 3.937 8 7 6 5 5.132 4 3.96 B .46 7.258 1.03 .457 3.937 17.54 2.
APPENDIX 9.3.1 TECHNICAL SPECIFICATIONS FOR IDS 24” The IDS Display series is meticulously engineered to be adaptable and suited for an array of field operation, as well as being designed to support a wide selection of resolutions. The specifications unique to each particular LCD can vary. These particular specifications are available through our sales department. Environmental LCD Panel Active Display Size 24" Operating Temp 0°C to +50°C Native Pixels 1920 x 1200 (2.
APPENDIX D 9.3.2 SCHEMATIC OUTLINE FOR IDS 24” 4X 1/4-28 .232 .80 MODEL/SERIAL LABEL C 14.36 4 3 2 13.444 3.937 1 REVISIONS 4 REV DESCRIPTION DATE PREP APVD 01 ENGINEERING PROTOTYPE -- -- -- 3 2 1 REVISIONS REV DESCRIPTION DATE PREP APVD 01 ENGINEERING PROTOTYPE -- -- -- 4X 10-32 .25 4X 1/4-28 .232 .80 20.41 22.01 1.03 D .457 .457 4X 10-32 .232 4X 1/4-28 .296 1.76 MODEL/SERIAL LABEL B 5.211 D .80 .296 20.41 MODEL/SERIAL LABEL 9.32 3.03 C 13.
Z Microsystems, Inc. 9820 Summers Ridge Road San Diego, CA 92121 Phone: (858) 831-7000 Fax: (858) 831-7001 Website: www.zmicro.com Copyright 2012 Z Microsystems, Inc. All Rights Reserved Z Microsystems, Inc. Z Microsystems, Inc. · 9820 Summers Ridge Road, San Diego, CA 92121 · T: 858.831.7000 · F: 858.831.7001 · www.zmicro.
