Zachry K475 Zachry K1200D K-Series Compact Amplifiers Owner’s Manual K-Series Compact Amplifiers
ZACHRY CAR AUDIO CONGRATULATIONS ! You now own a ZACHRY CAR AUDIO K-series compact amplifier, the product of an uncompromising design and engineering philosophy. We suggest you take a moment to document the information below, which will be helpful in the event of theft or if service is needed. Please retain this manual and your sales receipt for future reference. ZACHRY CAR AUDIO amplifiers are the result of innovation and the highest quality control standards.
FEATURES l COMPACT SIZE AND TINY FOOTPRINT. l DOUBLE SIDE PCB AND SMD COMPONENTS. l FULL MOSFET DESIGN. l LPF AND HPF CROSSOVER. l ADJUSTABLE BASSBOOST. l 1-OHM LOAD STABLE FOR K1200D . l NOISE FREE DESIGN. l OVERLOAD, OVERHEAT, HIGH/LOW VOLTAGE PROTECTION. l RoHS COMPLIANT.
ZACHRY CAR AUDIO CONTROL FUNCTIONS 1. SPEAKERS Connect speakers/subwoofers to these terminals. Be sure to check wire for proper polarity. Never connect the speaker cables to chassis ground. 2. +12 Volt Power Connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of the vehicle battery or the positive terminal of an isolated audio system battery.
11. Hi-pass filter (Full range) This knob controls the frequencies played for the front channels. Low frequencies can be cut out from OFF to 200Hz. At OFF position, none low frequency cut out, that means full pass. 12. X-over mode and frequency Control (Full range) These controls allow control over the frequencies played for the rear channels. There is an option for Low Pass, Full Range or High Pass. In LP or HP mode, the crossover frequency can be tuned from 50Hz to 750Hz by the frequency knob. 13.
ZACHRY CAR AUDIO PANEL LAYOUT Fig 2. Mono amplifier panel layout 2 1 13 14 6 5 10 4 7 8 3 9 K1200D Digital Car Amplifier Zachry K1200D WIRING DIAGRAM Fig 3.
WIRING DIAGRAM Fig 4. Mono amplifier wiring (Multi-woofer load) Zachry K1200D FUSE REMOTE signal Source Unit RCA signal K1200D Digital Car Amplifier *Equivalent parallel woofer load cannot be less than the minimum load rating. The 2 negative terminals are paralleled inside the amplifiers, as are the 2 positive terminals. These are monoblock amplifiers, not multi-channel amplifiers. Minimum load for Zachry K1200D is 1 ohm.
ZACHRY CAR AUDIO CONNECTING THE AMPLIFIER 1. Select cable and fuse according to the following table. 2. Connect the amplifiers ground cable to a close, bare metal part of the frame or chassis. Use a nut and bolt, NOT a screw! The ground cable must be at least the same size as the +12volt cable. 3. Connect the remote terminal to remote output of the head unit using 16 gauge (or heavier) wire. 4.
WIRING DIAGRAM Fig 6.
ZACHRY CAR AUDIO TROUBLE SHOOTING Symptom Possible Remedy Amplifier will not power up Check to make sure you have a good ground connection. Check that there is battery power on the (+)terminal . Check all fuses, replace if necessary . Make sure that the Protection LED is not illuminated. Protection LED Comes on Check for short circuits on speaker leads. Check the speaker load not beyond the minimum load. Remove speaker lead, and reset the amplifier.
SPECIFICATIONS Model Zachry K1200D Zachry K475 Description 1200Wrms Mono 4 X 75Wrms RMS power at 14.4V 1 Ohm Load 1200 Wrms NA 2 Ohm Load 700 W 4 X 120 W 4 Ohm Load 450 W 4 X 75 W Features Input Level 0.2~5V Frequency Response 10~220Hz 15 Hz ~25KHz LPF 40~220Hz 50 Hz ~750Hz SubSonic Filter(HPF) 10~50Hz 50 Hz ~750Hz THD at 4ohm load 30% Rated Power <0.3% <0.
K-Series Compact Amplifiers