(English version) ZM-GWB3 VGA WATER BLOCK for Higher Water Cooling Performance Please visit our website and watch the ZM-GWB3 installation video for easy installation. ※ Please read this manual thoroughly before installation. ※ The specifications of this product and its components may change without prior notice to mprove performance. http://www.zalman.co.kr http://www.zalmanusa.
Precautions 1) Test the product for leakage away from the system before installing it on the system. After no leakage is confirmed, proceed with installation and use. 2) Use approved coolant for computer water-cooling to prevent corrosion. 3) Use coolant tubes listed under the compatibility list. 4) Do not use the product if it interferes with any VGA components. 5) Familiarize yourself with this manual. 6) Keep this product and its associated system away from children. Disclaimer Zalman Tech Co., Ltd.
. Components 1) Common Components ① VGA Water Block Assembly ② Four(4) Nipple ❶ ③ Four(4) Nut) ❷ ④ Washer Plate ⑤ Four(4) Rubber Ring ⑥ Four(4) Spring ⑦ Four(4) Bolt ❸ ⑧ Two(2) Tube Clamp ❹ ❺ ❼ ❽ ⑨ Thermal Grease ⑩ User’s Manual ❻ Nipple Installation Holes for Various VGA Cards Nipple Installation Holes ❶ ❷ ❸ ❹ ❺ VGA Card ATI X1600 Series ATI X1300 Series ATI Radeon 9 *** Series (except 9550/9600) ATI Radeon X ** Series NVIDIA Geforce4 MX Series NVIDIA Geforce FX 5200 NVIDIA Geforce FX 550
. Exploded View Bolt GWB3 Ass’y Nipple Rubber Ring Washer Plate Spring Nut ※ The specifications of any product may change without prior notice to improve performance.
. Installation Procedure 1) Install Nipples and Fixing Nuts Insert the Nipples and Rubber Rings into the front side of the VGA card, then install the Washer Plate (PVC), Springs, and Fixing Nuts in the mentioned order. Note 1) Screw the Fixing Nuts only to a point so that the Fixing Nuts stay connected to the Nipples (approximately two screw turns). Note 2) The ends of the Springs are of different diameters. Install the Spring end with the shorter diameter on the Fixing Nut.
3) Installing the VGA Water Block Place the VGA Water Block and the clip on the center of the VGA chipset. Screw each bolt B on each nipple slightly, and tighten each bolt a few turns at a time while alternating between the two until the bolt ends are completely pressed against the Nipples. Bolt Note 1) Nipples and Fixing Nuts are not completely fixed on to each other, therefore hold the Nipple with one hand while screwing in the Bolts.
5) VGA Card Installation Insert the assembled VGA card into the motherboard’s PCIe (or AGP) slot. Use the Fixing Bolt to secure the VGA card onto the computer case. If the VGA card has a power connector on it, remember to plug in th power cable. Fixing Bolt 6) Installing the Tubes and the Tube Clamps Plug the tubes over the VGA Water Block’sfittings and install the Tube Clamps.
2) Hooking the RWB1 Fixing Clip into the ATI hole positioned on the upper region of the VGA water block will create tension. Now hook the other side of the RWB1 Fixing Clip on to the upper part of the RWB1 in order to safely install the RWB1 RWB1 Fixing Clip ATI Hole 3) Installing the Tubes and the Tube Clamps Plug the tubes over the VGA Water Block’s fittings and install the Tube Clamps. Note 1) Use a proper tool (e.g. cutting nipper)when installing the Tube Clamps.
Zalman Noise Prevention System Stable performance and noiseless liquid cooling system can both be achieved with the use of Zalman’s Noiseless Power Supply, HeatPipe Hard Disk cooler, Noiseless Case Fan and Northbridge Water Block.
