English Version
RESERATOR XT RESERATOR XT Installation and Operational Notes Installation Notes English English Version 1. Do not place the unit in dusty or humid conditions, under direct sunlight, or near a heat source such as a room heater. 2. Do not drop or subject the unit to excessive force. 3. Check the CPU socket compatibility before installation. 4. Do not mix any contaminants with the coolant when filling. It may cause product failure or corrosion. 5.
RESERATOR XT Table of Contents Installation and Operational Notes 1. Features •High Performance Ultra Quiet Water Cooling System •Active/Passive Hybrid Cooling Design - Active Cooling: 140mm Fan (Forced Convection Cooling) - Passive Cooling: Anodized Aluminum Heatsink Chassis(Natural Convection Cooling) •Automatic/Manual Control Modes - Automatic Mode: Coolant Temperature is monitored for Automatic Control of Fan Speed and Coolant Flow Rate.
RESERATOR XT 2. Specifications RESERATOR XT 3. Installation Overview English 2.1 Reserator XT (Reservoir+Radiator+Water pump) 1) Weight : 7kg 2) Materials : Anodized Pure Aluminum 3) Dimensions : 350(L) x 210(W) x 180(H)mm 4) Maximum Coolant Capacity : Max. 1.25ℓ 5) Integrated Water Pump : 6W, DC 12V, 300L/Hr 6) Maximum Lift : 1.8m CPU WATER BLOCK 2.2 CPU Water Block (ZM-WB5) 1) Weight : 160g 2) Materials : Base Cover (Pure Aluminum), Base (Pure Copper) 3) Dimensions : 63(W) x 63(L) x 40(H)mm 2.
RESERATOR XT 5. Installation Guide 4. Components 1) Reserator XT- 1 Unit RESERATOR XT 6) PVC Tube - 4m 2) CPU Water Block (ZM-WB5) - 1SET English 7) I/O Bracket - 1EA 5.1 Reserator Placement The Reserator’s placement should be determined in relation to the position of the PC. Place it upright, next to or slightly above the PC. Note that if the Reserator is placed lower than the PC, the PVC Tube’s internal air pressure may prevent proper initial operation.
RESERATOR XT PUSH English 5.3 Reserator XT’ s Coolant Circulation 1) The purpose of connecting the Jump Cable of the Power Supply’s Main Connector (20P/24P) is to receive direct current (12V) needed for the test run and leakage inspection. 2) For smooth initial degassing, connect one end of the Degassing Tube to the OUT terminal of the Reserator, and repeatedly press the opposite Quick Coupling end - with the finger to discharge the internal air.
RESERATOR XT 5.4 CPU Water Block Installation (ZM-WB5) 1) Refer to the manual provided with the ZM-WB5 for installation. 2) If interference occurs while installing the Water Block, then stop the installation. 5.7 DC Power Cable Connection 1) Fit the DC Cable’s Cord Bushing into the groove of the I/O Bracket, and fasten the I/O Bracket with a Bolt. 2) Connect the DC Cable Connector to the 4-Pin Connector of the Power Supply. Note 1) Do not exert excessive force when connecting the connector.
RESERATOR XT 5.8 Confirmation of Proper Installation 1) Check if the product is placed properly. 2) Check if the coolant’s circulation path conforms to the path shown below. 3) Slightly tug on the PVC Tubes connected to each Fitting to check for loose connections. Reserator OUT CPU Water Block English - CPU Water Block and Reserator’s Base OUT Connection 1) Connect one end of the PVC Tube to the Fitting of the CPU Water Block and fasten with a Tube Clamp as shown in the diagram.
RESERATOR XT 5.10 Front Panel Display ② ④ ⑤ 15 ⑥ ⑦ •The specifications of this product and its components may change without prior notice to improve performance. ③ ◈ Front Panel Display ① Fan Speed Gage - Displays the Fan Speed(rpm). If there is a problem, the display will flicker. If the flickering is observed, please check if there are any mechanical or pump related problems.
RESERATOR XT Zalman Noise Prevention System Stable performance and noiseless liquid cooling system can both be achieved with the use of Zalman’s Noiselee Power Supply, VGA Water Block, Northbridge Water Block, VGA RAM Water Block.
