822 61 10-69
Contents For the Installer For the user Safety Information 3 Description of the appliance 4-5 15 Unpacking 16 - Damages - Use - Identification of materials - Spray arm - Coarse strainer/microfilter - Fine filter - Detergent dispenser - Rinse aid dispenser - Water softener The control panel Technical Specifications Installation - Positioning - Water inlet - Water drainage - Power supply 6 - How to set the delayed start Adjusting the water softener 7 Programme chart 8 Using the appliance 9
Safety information Before installing and first using the dishwasher, read this instruction booklet carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the dishwasher are thoroughly familiar with its operation and safety features. Save these instructions and make sure they remain with the dishwasher if it is moved or sold, so that everyone using it through its life can be properly informed on appliance use and safety.
Description of the appliance 4 5 -4-
Spray arm (1) It is important to keep all the holes in the spray arm clear. A clogged hole can seriously affect washing efficiency. If the spray arm needs cleaning, unscrew the nut anticlockwise, remove the washer and lift off the spray arm. Clear the holes and shake out any food remnants. Coarse strainer/microfilter (2) The purpose of the coarse strainer is to catch large objects such as toothpicks and pieces of eggshell. Make sure that the strainer is always clean.
The control panel Indicator and control lamps Indicator lamps delayed start A On/Off button Delay start button Water softener button Programme buttons Control lamp Combination buttons ”Cancel” / ”A” In addition to selecting a programme, you can press these two buttons to adjust the setting of the water softener and cancelling a pre-set programme. Indicator lamps: Control lamps: Shows • Current phase of the selected programme.
Adjusting the water softener To prevent limescaling on the dishes and to the interior of the dishwasher, the dishes must be washed with soft water. Contact your local Water Authority to find the exact water hardness level for your area. This dishwasher is equipped with a water softener, where tapwater which is harder than 4 °d (german degree) is softened. The water softener has 5 settings: Adjust the water softener according to the table below for the water hardness level for your area.
Programme chart All types of dishes Type of dishes Plates and cooking pots Type of soil: • heavily soiled • normaly soiled • dried-on food remnants especially eggwhite and starch • dried-on food remnants • normaly soiled Coffee cups, delicate items • lightly soiled • lightly soiled Suitable programme: INTENSIVE 70° C Programme cycle: 1) Pre-wash Washing 2 x rinses Final rinse Drying NORMAL 65° C Pre-wash Washing Rinse Final rinse Drying ENERGY SAVE 55° C 3) Pre-wash Washing Rinse Final rinse D
Using the appliance Starting the programme Pause function 1. Scrape or rinse off solid food remnants. With the pause function the programme can be temporarily interrupted for a short period of time. 2. Load the dishwasher. (See the basket and loading). 1. Press in the On/Off button. The programme stops. 3. Put the correct amount of detergent into the detergent dispenser and close the dispenser lid. 2. All lamps goes out. 3. When you want the programme to continue again, you press the On/Off button.
Loading and unloading the dishwasher How to load the dishes Baskets The illustration shows the dishwasher loaded with six place settings. Your own dishes are not likely to be identical to this load, but if you follow the advice below we are sure you will be pleased with the results. Main basket Cutlery basket The cup shelves can be placed in two different levels. ● Always place glasses, cups and bowls upside down. ● Incline deep dishes (soup plates etc.) so that the water can run off when drying.
Maintenance and cleaning General cleaning Moving the dishwasher Inspect the filters and spray arm nozzle before re-loading the dishwasher and remove any food scraps. Wipe round the rubber gasket at the bottom of the door to remove grease which tends to collect there. If you have to move the dishwasher (you are moving house, etc): 1. Unplug it. 2. Turn off the water tap. Cleaning the filters 3. Remove the water inlet and discharge hoses.
Something Not Working Before calling out an engineer, please check through the details below because some faults can be rectified easily without the need to call out an engineer. If an engineer is called to resolve a problem listed below or to repair a fault caused by incorrect installation or mis-use a charge will be made, even if the appliance is under guarantee. Fault Check The programme will not start.
Service Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning: 08705 929929 1. 2. 3. 4. 5. Your name, address and post code Your telephone number Clear and concise details of the fault The model and serial number of the appliance (found on the rating plate) The purchase date Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
Guarantee Conditions Standard guarantee conditions We, Zanussi Electrolux, undertake that if within 12 months from the date of the purchase this ZANUSSI ELECTROLUX appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: • The appliance has been correctly installed and used only on the electricity supply stated on the rating plate • The ap
Installation instructions Any electrical work required to install this appliance, should be carried out by a qualified electrician or competent person. Any plumbing work required to install this appliance, should be carried out by a qualified plumber or competent person.
Unpacking Damages If the dishwasher has been damaged during transport, you should immediately notify the company responsible for delivering it. If you discover any damage, faults or that anything is missing, you should notify your retailer immediately. Never leave packaging material in a place where children may play with it.
Installation Positioning The dishwasher is intended to be installed on a kitchen sink, worktop or built-in. To function properly, make sure that the appliance is level. Its height can be adjusted with the adjustable feets (5 mm each). See the illustration for built-in measurements. Water inlet The dishwasher is equipped with safety features which are to prevent the water from going back to the fresh water system. These features are according to current water technical safety regulations.
Installation Water drainage To protect the dishwasher against water damage it is equipped with a water safety system. In the event of a fault the drain-pump starts automatically and the remaining water inside the dishwasher is pumped out. The water safety system also works when the dishwasher is switched off. However the dishwasher must be connected electrically. Place the discharge hose over the sink as illustrated.
Power supply The dishwasher is supplied with a lead and electrical plug for connection to a 230 V, 13 A earthed wall socket. Before any work is carried out on the dishwasher, it must be isolated from the electric mains supply, for example by removing the plug from the wall socket. Permanent electrical installation must be carried out by an authorised electrician or competent person. WARNING: THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should this safety measure not be observed.
© Electrolux plc 2004