User Manual Gas Cooker ZCGHL50 BACK LEFT FRONT LEFT GRILL MAIN OVEN FRONT RIGHT BACK RIGHT
Important safety information These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using the appliance. Your safety is of paramount importance. If you are unsure about any of the information in this book contact the Customer Care Department. Installation The appliance must be installed according to the instructions supplied.
Ensure that all vents are not obstructed to ensure ventilation of the oven cavity. Never line any part of the appliance with foil. Always stand back from the appliance when opening the oven door to allow any build up of steam or heat to release. Never leave the appliance unattended when the oven doors are open. Do not place sealed cans or aerosols inside the oven. They may explode if they are heated. Ensure that all control knobs are in the OFF position when not in use.
Contents For the user Important safety information Description of the appliance Getting to know your appliance Before using the appliance Rating plate Preparing to use your appliance Condensation and steam Cookware Grill and oven furniture 2 5 6 7 7 7 7 7 7 The hob Using the hob To light the hob burners To turn off any burner Things to note Hints & tips 8 8 8 9 9 9 The grill Using the grill Things to note The grill pan and handle Hints & tips Grilling chart 10 10 10 10 11 12 The main oven Heat zones P
Description of the appliance Gas high level grill with single oven Grill BACK LEFT FRONT LEFT GRILL MAIN OVEN FRONT RIGHT BACK RIGHT Control Panel Main Oven Storage Compartment 5
Getting to know your appliance The control panel B C D S 9 A 12 E Features A - Hotplate controls B - Grill control C - Main oven temperature control D - Hotplate controls E - Ignition switch 6 5 7 8 3 4 9
Before using the appliance Rating plate This is situated on the lower front frame of the appliance and can be seen upon opening the door. Alternatively the rating plate may also be found on the back or top of some models (where applicable). The appliance must be protected by a suitably rated fuse or circuit breaker. The rating of the appliance is given on the rating plate. Do not remove the rating plate from the appliance as this may invalidate the guarantee.
The hob Using the hob The gas hob has different burner sizes to suit different types of cooking: To ensure maximum burner efficiency only use pots and pans with flat bases appropriate to the burner size used. Larger burner (Rapid) - use a large pan for food such as chips. Medium burners (Normal) - use for everyday cooking. Small burner (Simmer) - use for simmering foods such as soups and stews. The largest pan which you should use on any burner is 230mm (9").
To turn off any burner 1. Turn the control knob to the off position. This is shown by a large dot. When lighting any burner, ensure that it is lit before you leave the appliance. When turning off a burner, ensure the flame has gone out before leaving the appliance. In the event of the burner flames being accidentally extinguished, turn off the burner control and do not attempt to re-ignite the burner for at least 1 min.
The grill CAUTION – Accessible parts may be hot when the grill is in use. Young children should be kept away. When you first operate the grill you may hear some sounds as the burner heats up, this is quite normal and is not a fault on the appliance. Using the grill • Push in the control knob and turn to the large flame symbol (highest setting). Press the ignition button immediately. • When the burner has lit release the control and ignition button, adjust the setting as required.
NOTE: Taptite screws are used to secure the handle. These are thread forming screws and sufficient pressure must be applied to allow the screws to produce a thread in the plunged holes. The grill pan is designed so that you can pull it forward but it will stay supported. To remove the pan push it back as far as possible and lift it off. Replace it in reverse order. Place the grill pan on the shelf so that the pan is positioned centrally beneath the grill.
Grilling chart Food Bacon Rashers Beefburgers Position Grill time (mins in total) Adjust 5-6 grill 10 - 15 Chicken Joints 30 - 40 setting Chops – Lamb Pork and 15 - 20 20 - 30 Fish – Whole Trout/Mackerel grill 15 - 25 Fillets - Plaice/Cod pan 10 - 15 Kebabs grid 20 - 30 to 8 - 12 suit 10 - 20 different 20 - 30 Steaks – Rare Medium Well Done thicknesses of 6 - 12 12 - 16 14 - 20 Toasted Sandwiches food 3-4 Kidneys – Lamb/Pig Liver – Lamb/Pig Sausages The times quoted above
The main oven There are zones of heat within the oven. The temperature in the middle is the gas mark you have chosen. The top of the oven is slightly hotter and the lower shelf slightly cooler. The base of the oven is quite a lot cooler. You can make use of these heat zones when you are cooking foods requiring different temperatures all at the same time.
• • • • • • • • Hints and tips Arrange the shelves in the required positions before switching the oven on. Shelf positions are numbered from the top downwards. Ensure that food is placed centrally on the shelf and there is sufficient room around the baking tray/dish to allow for maximum circulation. Do not push dishes too far back as food will burn if it overhangs the burner flame.
Cooking chart The oven temperatures are intended as a guide only. It may be necessary to increase or decrease the temperatures to suit individual preferences and requirements. Food Biscuits Bread Bread rolls/buns Cakes: Small & Queen Sponges Victoria Sandwich (7”) Madeira (7)” Rich Fruit (8)” Christmas (8)” Gingerbread Meringues Flapjack Shortbread Casseroles: Beef/Lamb Chicken Convenience Foods Fish Fish Pie (Potato Topped) Fruit Pies, Crumbles Milk Puddings Pasta/Lasagne etc.
Roasting chart INTERNAL TEMPERATURES – Rare : 50-60°C; Medium : 60-70°C; Well done : 70-80°C MEAT GAS MARK COOKING TIME 25-35 minutes per ½kg (1lb) and 20-35 minutes over Beef/ Beef boned 5 Mutton/Lamb 5 25-35 minutes per ½kg (1lb) and 25-35 minutes over Pork/Veal/Ham 5 30-40 minutes per ½kg (1lb) and 30-40 minutes over Chicken 5 20-25 minutes per ½kg (1lb) and 20 minutes over Turkey/Goose 5 20-25 minutes per ½kg (1lb) up to 3½kg (7lb) then 10 minutes per ½kg (1lb) over 3½kg (7lb) Duck 5
Slow cook The slow cook setting gives a very low heat in the oven. It is particularly useful when you are cooking soups, stews and casseroles because the long slow cooking will make cheaper, tougher cuts of meat more tender. Some foods such as pastry and biscuits are not suitable for slow cooking because the temperature is too low. Cover all food during cooking to prevent it from drying out. You can uncover food for the last half hour if it is normally served golden brown.
Soups, casseroles and stews Flavouring • Do not cook casseroles over 2.7 kg (6lb). • Bring to the boil on the hotplate then cook on slow cook. Flavours are held in the food because there is little evaporation. Adjust flavouring at the end of the cooking time. • Cook on the middle shelf of the oven or above. • Cover food with a tight fitting lid or tin foil. Vegetables Use slightly less liquid as there is little evaporation during cooking.
Care and cleaning Before cleaning always allow the appliance to cool down. Cleaning materials Before using any cleaning materials on your appliance, check that they are suitable and that their use is recommended by the manufacturer. Cleaners that contain bleach should NOT be used as they may dull the surface finishes. Harsh abrasives must also be avoided. Cleaning the outside of the appliance Do not use abrasive cleaning materials e.g.
Cleaning the hob Clean the hotplate top using a mild abrasive. Take care not to damage the spark electrodes. If the spark electrodes are damaged the burners will not light. You can remove the pan supports, burner caps and burner crowns to clean them. Again take care not to damage the spark electrodes. Clean the burner crowns and pan supports by soaking them in very hot soapy water. Aluminium based saucepans can leave shiny metal marks on the pan supports.
Cleaning the shelves and grill/oven furniture All removable parts, can be washed in the dishwasher. The grill pan, grill pan grid and oven shelves may be cleaned using a soap impregnated steel wool pad. Soaking first in hot soapy water will make cleaning easier. Cleaning the grill Do not clean the grill burner itself. Cleaning the grill may cause the holes in the burner to become blocked preventing it from operating correctly.
Cleaning the door(s) To prevent damaging or weakening the door glass panels avoid the use of the following: • Household detergents and bleaches • Impregnated pads unsuitable for non-stick saucepans • Brillo/Ajax pads or steel wool pads • Chemical oven pads or aerosols • Rust removers • Bath/Sink stain removers Cleaning between the outer and inner door glass The outer door glass is removable for cleaning. To remove the outer glass 1. 2. 3. 4. 5.
If the door glass panel becomes chipped or has deep scratches the glass will be weakened and must be replaced to prevent the possibility of the panel shattering. Please contact your local Service Force Centre who will be pleased to advise further. To replace the outer glass 1. 2. 3. 4. Holding the oven glass with both hands, gently place the locators into the holes of the brackets at the bottom of the oven door.
Something not working Maintenance must only be carried out by a competent/qualified person. Do not try to alter/modify the appliance yourself, as this could be dangerous. We recommend that your appliance has an annual gas safety check carried out by our approved service organisation. Please carry out the following checks on your appliance before calling a Service Engineer. It may be that the problem is a simple one that you can solve yourself without the expense of a service call.
Something not working continued Problem Possible solution The burner is not igniting or only partially lighting. Check that the burner is dry and that food spillage or cleaning fluids are not present on the burner. This can be dried with a cloth and stubborn marks cleaned away with a dry nylon brush (old toothbrush etc.) The burner sounds noisy. It is natural for the burners to emit noise as the gas is being drawn through the burner and may reduce as they heat up.
Service and spare parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning:O870 5 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.uk.
Guarantee conditions Standard guarantee conditions We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
Technical details Dimensions Height: Width: Depth: Weight: 1462mm (nominal) 498mm 600mm (from elbow to front of door panel) 52 .0 Kg Height to hotplate 907 mm nominal. See important note ‘Location of appliance’. Space for fixing at hotplate level 2mm minimum clearance 600 nominal Space for fixing above hotplate level 100mm each side of appliance.
Grill Heat Input Injector marking Main Oven Heat input Injector marking Thermostat bypass marking General Ignition Spark gap Natural Gas 3.0kW (10236 Btu/h) 120 L.P. Gas 2.75kW (197.5g/h) 080 2.4kW (8189 Btu/h) 108 069 2.4kW (172.4g/h) 078 078 (H.T. Spark) 3-4mm Gas category countries of destination CAT. I2H CAT. I3+ GB GB This appliance complies with: European Council Directives Low voltage Directive 73/23/EEC, Gas Directive 90/396/EEC EMC Directive 89/336/EEC, CE Marking Directive 93/68/EEC.
Installation instructions Important - safety requirements Where applicable Natural Gas and L.P Gas versions of this appliance are available. Check that this model is suitable for the type of supply available. This appliance must be installed and/or serviced by a competent person in accordance with the Gas Safety (Installation and Use) Regulations Current Editions and the I.E.E. Wiring Regulations. Detailed recommendations are contained in the following British Standard Codes of Practice – BS.6172, BS.
To move the appliance, open the grill door. Raise the appliance off its front feet by lifting it from inside the oven. Pull the appliance forward. When you replace the appliance push it back to the stop and make sure there is the same gap at each rear corner. For your safety Do not try to disconnect the appliance from the gas supply if the supply pipe does not have a bayonet connection, as described in the installation instructions. If this is the case contact the person who installed the appliance.
Levelling the appliance Adjustment to suit floor conditions or height is obtained by rotating clockwise or anti clockwise the feet at the front and rear of the appliance. A spirit level should be placed on one of the shelves to confirm the appliance is correctly levelled. Grill assembly The two splashback screws marked A (see Fig.2a) should be screwed into the back of the appliance about halfway in. Engage the keyhole slots in the splashback behind the two screws taking care not to trap the H.T.
Connecting to gas supply This appliance is designed to be installed with an appliance flexible connection only. Supply piping should not be less than R3/8. Connection is made to the Rc ½ (½” B.S.P.) female threaded entry pipe located just below the hotplate level on the rear left hand side of the appliance. NOTE: ONLY LIQUID SEALANTS TO BE USED WHEN INLET GAS PIPE IS FITTED I.E.: DO NOT USE P.T.F.E. SEALANT TAPE. Carry out a gas tightness test after connecting to the gas supply.
3. Draw a line 100mm from the front edge of the feet (see Fig.3a) and remove appliance from its position. Mark off dimension 'B' (see Fig.4a) back from this line on the centre line of the bracket to locate the front edge of the lower bracket. Fix lower bracket (with two fixing holes) to the floor then measure the height from floor level to engagement edge on back of appliance, dimension 'C'of Fig. 4b. 4.
2. 3. 4. 5. Connect the pressure gauge to the oven injector. Check the supply pressure by turning the thermostat on and one hotplate tap full on and light the appropriate burner. The pressure should be either:(i) For Natural Gas 20mbar (ii) For LP. Gas. The pressure must be set to 28 mbar for use on butane or 37 mbar for use on propane. Turn off the taps, disconnect the pressure gauge and replace oven burner and cover, ensuring that the F.S.D phial is correctly located into the bracket on the burner.
www.electrolux.com www.zanussi-electrolux.co.
