TECHNICAL DATA Width 242 ins Overall depth (excluding hose) 188 ins Height 335 ins Weight 1763 lbs Dry clothes capacity {excluding synthetic fabrics and wool) g ibs Heater rating 1800 W Motor rating during washing Mo tar rating during spinning 0.12 HP er load . o 3.
INSTALLATION UNPACKING Remove the cardboard packing, reinforcing angle pieces and polythene wrapping and proceed as follows: 1} Tilt the machine and remove base packing (fig. 1}. 2) Remove back panel, undoing the two fixing screws. 3] Remove the brackets (A fig. 2) securing the wash unit to the back of the machine. 4} Remove the 4 screws securing the lid and lift off the same. 5} Remove the screws and nuts which fix the transit bar {fig. 3} to the cabinet.
LEVELING Move the washer to Its permanent operating location and carefully level it by adjusting the feet and locking them in position with the nut on the shank (A fig. 4). in order to avoid any vibration or movement of the appliance during washing, this operation must be carried out properly. Furthermore, make sure that the washer does not touch walls, furniture, ete.
If the water connection is made note new pipes or onto pipes which have not hen used for a long time, it is advisable to run off a certain amount of water before connecting the machine. This will avoid foreign matter blocking the filter placed at the end of the water inlet hose. Drain hose: hook the curved end of the outset hose over the edge of a sink or insert it into a drain pipe not Jess than 20 ins. and not more than 34 Ins. from floor level {flg. 6).
ELECTRICAL CONNECTION WARNING: THIS APPLIANCE MUST BE EARTHED. Connection to the electrical supply shouts be made by a 3 pin pin 15 A plug. If a BS 1363 3 pin 13 A fused plug and socket Is used, the plug should be fitted with a 13 A fuse. If a 15 amp plug and socket is used this should be protected fuse either in the plug or at the distribution board. The manufacturer declines any liability should this safety measure not be ch served.
OPERATING INSTRUCTIONS PRELIMINARY HECK Carry out the following check before using the machine: i the plug in the socket? is the power on? — is the water inlet hose connected to the tap and the tap turned on? — has the drain hose been placed on the edge of a sink or in 2 drain? is the machine door properly closed? STARTING STOPPING To start the machine select the programmer required and pull out the timer {programmer selection) control. This switches on the machine.
grimes. Each programmer has been specially designed for a specific type .of fabric (e.g. cotton, sympathetic fibers, wool, effete. The appropriate programmer must therefore be chosen according to the type of fabric 10 be washed. FILLING WITH WASHING POWDER The washing powder dispenser is located on the left front side of the control panel. Pull out dispenser and add washing powder.
specially designed to complexity the cleaning action of these machines. 8o use it regularly for trouble free wishing and superb results. Do use enough powder, To gui you clothes really clean It is essential that enough powder is used in the machine. The correct amount will depend on a number of things — the hardness of the water, the size of the road, and the amount of soling present. As a guide we suggest you follow the table below and adjust the amounts In light of your personal experience.
WASHING PROGRAMMED COTTON LINEN b Whites heavy soil bio rewash Rewash in warm water. Vigorous wash in very hot water. 5 rinses in cold water. Spinning. Put the powder required for bloatware into compartment < a» and for the main wash into compartment required, pour the liquid additive into compartment « ¢ », Whites Vigorous wash in very hot water. 5 rinses in cold water. Spinning. Put the powder required for the main wash into compartment required, pour the liquid additive into compartment « ¢ ».
WASHING PROGRAMMED 4 Non fast coloreds Vigorous wash in warm water. 5 rinses in cold water. Spinning. Put the powder required for the main wash into compartment required, pour the liquid additive into compartment con, Rinses Special treatments 5 rinses in cold water. Spinning. if required, pour the Haida additive into compartment « ¢ » taking care not to exceed the level of the filter. Spin Spinning far about § minutes with water draining. #t is important to place timer index line exactly on No.
WASHING PROGRAMMED SYNTHETICS WOOL DELICATE NOTE: There is no water draining in the last rinse of the gents action wash cycles to prevent the clothes from creasing if they are left in the machine at the end of the wash cycle. To complete the cycle, turn the timer knob centering it on the symbol m 7 8 White nylon heavy soil Rewash in lukewarm water. Gentle wash in hot water. No spinning. Put the powder required for rewash into compartment « a » and for the main wash into compartment «h».
CARE AND CLEANING OF THE MACHINE important: make sure that the plug has been removed from the socket prior to undertaking any kind of maintenance. From time to time, carry out'a complete cycle without a washing load, adding 1 oz of «Glucagon ». This should also be done when the washer has been out of use for a long time. — Leave the door ajar for about 2 hours after the wash to allow air to circulate freely inside the machine.
""HINTS FOR CARE OF WASHING "POWDER' DISPENSER W recommend that the washing. powder dispenser Is checked regularly to en sure that it Is clean dry. Do wipe the dispenser after each wash, Should the dispenser require special cleaning,, the drawer. can be composite» removed, and the. Interior cleared of any deposit. The drawer can be removed from the front of the appliance by giving a sharp pull outwards. A sharp tap with the palm of the hand may bé necessary when replacing the drawer.
Industries A. Gaussian spa RSN ‘GAUSSIAN GUARANTEE CONDITIONS This guarantee is in addition to your statutory and other legal rights which will not be excluded or in-any way diminished by the return of the enclosed card.