WASHING MACHINE PRALKA AUTOMATYCZNA AUTOMATICKÁ PRACKA AUTOMATICKÁ PRÁCKA AUTOMATA MOSÓGÉP FAE825V FAE1025V 35.292.
Dear customer, Please read these operating instructions carefully and pay particular attention to the safety notes indicated in the first pages. We recommend that you keep this instruction booklet for future reference and pass it on to any future owners. Transport damages When unpacking the appliance, check that it is not damaged. If in doubt, do not use it and contact the Service Centre.
Warnings Disposal 4-5 Maintenance 5 Tips for environmental protection 5 Technical specifications Installation 6 7-8 Unpacking 7 Hydraulic connection 7 Levelling 8 Electrical connection 8 Your new washing machine 9 Description of the appliance 9 Detergent dispenser drawer Use Control panel Controls Washing hints 10 10 10-12 13 Sorting the laundry 13 Temperatures 13 Before loading the laundry 13 Maximum loads 13 Laundry weights 13 Removing stains 13 Detergents and additives 1
Warnings The following warnings are provided in the interests of overall safety. You must read them carefully before installing or using the appliance. Installation • Leave the porthole door slightly ajar when the appliance is not in use. This preserves the door seal and prevents the formation of musty smells. • All internal packing must be removed before using the appliance.
• Keep all detergents in a safe place out of children’s reach. • Children are often not aware of how dangerous electrical appliances can be. When the machine is working, children should be carefully supervised and not be allowed to play with the appliance. • Make sure that children or pets do not climb into the drum. • When the appliance is to be scrapped, cut off the electrical supply cable and destroy the plug with the remaining cable.
Intallation instructions It is dangerous to alter the specifications or attempt to modify this product in any way. Care must be taken to ensure that the appliance does not stand on the electrical supply cable. Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person.
Transit security bars Hydraulic connection Before starting the machine up, the transport security bars must be removed as follows: You are advised to keep all the transport security bars in case the appliance has to be transported again. There should be a COLD WATER tap near the washing machine with a screwing on connection pipe of 3/4 gas for the water supply, a sink, a wash basin or a drainage system in the wall. Previously check if: 1. Unscrew and remove the three rear screws by means of a key.
IMPORTANT: The distance from the floor to the highest part of the hose should be between 60 to 90 cm. (It is advised to be between 60 and 70 cm). The hose must not be bent nor twisted to avoid clogging. Should a prolongation of the discharging hose be unavoidable this must never surpass 1.5 m and must be of the same diameter as the original hose. Make sure the hoses are not too tense. 90 cm. Max. 60 cm. Min. 1,5 m. Max. Electrical connections Before plugging the appliance make sure that: 1º.
This new machine meets all modern requirements for effective treatment of laundry with low water, energy and detergent consumption. • The balance control device ensures the machine is stable during the spin.
Use Control panel 1. Detergent dispenser drawer 3. Programme option buttons This option is available for COTTON, LINEN and SYNTHETIC programmes. By selecting this button the machine will inserts a impulse spin and an anticrease phase after final spin in COTTON programs. In SYNTHETIC programs, by selecting this button the machine will inserts a cool-down after washing phase and an anticrease phase after final spin.
7. Programme progress display DELAY START button When DELAY START option is chosen, the light relevant to the selected delay lights up. After the machine has started, the remaining time is shown by the corresponding indicator light. This button allows the delay of starting of the washing programme by 12 H, 8 H, 4 H and 2 H hours. The delay which has been selected is indicated when the corresponding light comes on. To use this option proceed as follows: 1.
9. Programme selector dial 8. Spin speed selector dial, NO SPIN or RINSE HOLD option Model FAE 1025 V Model FAE 825 V The selector dial can be turned either clockwise or counter-clockwise. Use this selector dial to select the required programme. This dial allows the reduction of the final and the intermediate spin speed or to select NO SPIN or RINSE HOLD (no-wrinkle) options. At the end of each programme the selector dial must be turned to position “O”, to switch off the machine.
The following weights are indicative: bathrobe Sorting the laundry Follow the wash code symbols on each garment label and the manufacturer’s washing instructions. Sort the laundry as follows: whites, coloureds, synthetics, delicates, woollens. Temperatures 90° 60° for normally soiled white cottons and linen (e.g. tea cloths, towels, tablecloths, sheets...) for normally soiled, colour fast garments (e.g. shirts, night dresses, pyjamas....
Quantity of detergent to be used Ink: depending on the type of ink, moisten the fabric first with acetone (*), then with acetic acid; treat any residual marks on white fabrics with bleach and then rinse thoroughly. The type and quantity of detergent will depend on the type of fabric, load size, degree of soiling and hardness of the water used. Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with detergent paste. (*) do not use acetone on artificial silk.
These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry. Energetic wash 95 60 40 30 Max. wash temperature 95°C Max. wash temperature 60°C Max. wash temperature 40°C Max.
Operating sequence Before washing your first load of laundry, we recommend that you run a cotton cycle at 60° C, with the machine empty, in order to remove any manufacturing residue from the drum and tub. Pour half of the normal amount of detergent into the main wash compartment and start up the machine. 1. Place the laundry in the drum 4. Select the required programme Open the door by pulling the handle outwards. Place the laundry in the drum, one item at a time, shaking them out as much as possible.
9. Modification of a running washing programme Push DELAY START button as many times as necessary until the corresponding light to the required delay (12 H, 8 H, 4 H, 2 H) comes on. Once the programme has started, it only can be modified by turning the programme selector dial to “O” and afterwards the new programme can be chosen. The washing water remains in the tub, provided that the machine does not reach the rinse phase, since, in this case, the machine drains it automatically.
12. At the end of the programme The machine stops automatically. Release of the lock is indicated when END light comes on. Turn the programme selector dial to position “O” to switch the machine off. Remove the laundry from the drum and carefully check that the drum is empty. If you do not intend to put in another wash, turn off the water tap. Leave the door open to prevent from forming mildew and unpleasant smells.
ENGLISH Programme table Washing programmes for cotton and linen Load: 5 Kg. Programme selector dial position Washing programme Stains and type of fabric Description Possible option or A WHITES B ECONOMY (**) For heavily soiled cotton items. Wash at 90° C 3 rinses Spin White cotton, for example moderately soiled work garments, sheets, household linen, underwear, towels.
Programme table Washing programmes for synthetics, mixed fabrics, delicates, wool Load: 2 Kg., wool 1 Kg. Programme selector dial position Washing programme Stains and type of fabric Description Possible option or G MIXED FABRICS Mixed fabrics, underwear, coloured garments, perma-press shirts, blouses. Wash at 60° C 3 rinses Short spin or H SYNTHETICS Synthetic fabrics, underwear, coloured garments, perma-press shirts, blouses.
ENGLISH Programme table Special washing programmes Programme selector dial position Washing programme P RINSES Q DRAIN R SPIN O — Stains and type of fabric Description With this programme it is possible to rinse and spin garments which have been washed by hand. The machine performs 3 rinses, and it finishes with a short spin with the selected speed on the spin speed selector dial. 3 rinses Short spin To drain the water from the last rinse in programmes with RINSE HOLD option selected.
Maintenance 1. Bodywork 3. Cleaning of the drainage area Clean the outside of the machine with warm water and a neutral, non-abrasive household detergent. Rinse with clean water and dry with a soft cloth. The drainage area must be cleaned if the pump has been blocked with objects such as buttons, safety pins, coins, etc. , or if lint has built up because clothes that generate lint have been washed at high temperatures.
6. Frost precautions If it takes longer to fill up the washing machine it is time to check the water inlet hose filter it may be clogged. If the machine is installed in a place where the temperature could drop below 0°C, proceed as follows: Turn off the water tap. • disconnect the appliance; Unscrew the fixing nut of the inlet hose. • close the water tap; Remove the filter from the electrovalve and clean it with a hard bristle brush and replace it.
Something not working? Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling technical service. Before contacting your local Service Force Centre, please check the following possible problems listed below. During machine operation it is possible that correctly. END light flashes to indicate that something is not working • 4 flashes = door open. • 2 flashes = the water is not drained. • 1 flash = there is no water filling.
Possible cause - Unsatisfactory washing results: • Little detergent or an inappropriate one has been used. An insufficient amount of detergent leaves the laundry looking grey. • Stubborn stains have not been treated prior to washing. • The correct wash programme has not been selected. • Too much laundry has been placed in the drum. - The machine vibrates when spinning: • The transit bolts and packaging have not been removed. • The machine is in contact with the wall or furniture.
If you are unable to identify or solve the problem, contact our service centre. Before telephoning, make a note of the model, serial number and purchase date of your machine: the Service Centre will require this information. Mod. .......... Prod. No. ........... Ser. No. ......... Mod. .......... Prod. No. ........... Ser. No. ......... P0042 Water is not visible in the machine. The machine, which is the result of modern technology, runs in a very economical way with low water consumption.
Z·ruËnÌ podmÌnky Z·ruka vypl˝vajÌcÌ z tÏchto z·ruËnÌch podmÌnek je poskytov·na pouze kupujÌcÌmu spot¯ebiteli (d·le takÈ jen "KupujÌcÌ") a jen na v˝robek slouûÌcÌ k bÏûnÈmu pouûÌv·nÌ v dom·cnosti. Prod·vajÌcÌ poskytuje KupujÌcÌmu spot¯ebiteli Z·ruku v trv·nÌ dvaceti Ëty¯ mÏsÌc˘, a to od data p¯evzetÌ prodanÈho v˝robku KupujÌcÌm. KupujÌcÌ m· v r·mci Z·ruky pr·vo na bezplatnÈ, vËasnÈ a ¯·dnÈ odstranÏnÌ vady, pop¯ÌpadÏ - nenÌ-li to vzhledem k povaze (tzn.
EHPOESL/Z - 10/2002
