Upright Vacuum Cleaner Household Type Owner’s Guide Models Z1300, Z1400, Z4300 and Z4400 Series Index Important User Information ............ 2 Service Information ........................ 4 Guarantee ...................................... 4 Assembly .....................................5-6 Thermal Cut-Off .......................3 & 7 Use ................................................. 7 Accessories .................................8-9 Hose Blockage ........................10-11 Brush Roll .............
IMPORTANT USER INFORMATION IT IS MOST IMPORTANT THAT THIS INSTRUCTION BOOK SHOULD BE RETAINED WITH THE APPLIANCE FOR FUTURE REFERENCE. SHOULD THE APPLIANCE BE SOLD OR TRANSFERRED TO ANOTHER OWNER, OR SHOULD YOU MOVE HOUSE AND LEAVE THE APPLIANCE, ALWAYS ENSURE THAT THE BOOK IS SUPPLIED WITH THE APPLIANCE IN ORDER THAT THE NEW OWNER CAN BE ACQUAINTED WITH THE FUNCTIONING OF THE APPLIANCE AND THE RELEVANT WARNINGS. THESE WARNINGS ARE PROVIDED IN THE INTEREST OF SAFETY.
BEFORE YOU START CHECK THE VOLTAGE First check the voltage shown on the data plate (see rear view) to make sure that the cleaner is of the correct voltage for your electricity supply. If it is not, do not use the cleaner but refer back to your dealer. CONNECTING TO YOUR ELECTRICITY SUPPLY Permanently connected to the cleaner is a mains supply (2-core) cable fitted with a non-rewirable plug incorporating a 13A fuse.
SERVICE Should you require service on your Electrolux cleaner, please telephone Electrolux on 08706 055055. Before requesting service, please check whether your problem is covered under Service Checklist (see below). New filter pads, dust bags, brush rollers and drive belts can be obtained from Electrolux Retailers. If difficulty is experienced in obtaining spares, please contact Electrolux on 08706 055055.
HOW TO ASSEMBLE CAUTION: Assemble the cleaner before using. NOTE: Features may vary by model yet all parts assemble the same. Step B Attach Handle Step A Attach Hose CAUTION: Do not catch cord under handle. IMPORTANT: Hose MUST BE inserted before attaching the handle. 1 Tab Ledge Notch 2 4 Tab 3 Groove Hose Adapter Groove 1. Locate the tab on the hose adapter of the extension hose (shortest end). 2. Insert hose adapter into opening on top of unit.
Step C Store Hose and Accessories Step D Check Disposable Dust Bag 8 Combination Tool 10 8. Hook Remove front cover, grasp both sides of bag cover near top. Push thumbs against center of cover and pull out on sides. 9 Hose Adapter Crevice Tool 9. Carrying Handle Extension Wand or Wands 10. Paper Bag Collar Check to be sure the paper bag collar is secure with the hose adapter inside the paper bag collar. Replace front bag cover.
HOW TO USE The upright vacuum cleaner design allows use on multiple types of carpeting and on upholstery or bare floors with attachments. When using the attachment tools, place the handle in the upright position. Do not place cleaner on furniture or steps as the brush roll may cause damage. 1. Adjust cleaner height setting knob to lowest position for maximum cleaning. Adjust to a higher setting to make pushing easier. For easy adjustments, tilt the cleaner back to move the setting knob. 2 2 2.
How To Use Accessories NOTE: Do not place cleaner on furniture or stairs as the brush roll may cause damage. Place cleaner on floor with the handle in storage position while using accessories. Dusting Brush is for furniture, blinds, books, lamp shades, shelves. (On some models.) 1. Remove hose from rear of cleaner. 2. Place desired accessory onto end of hose or tube. Always work with the cleaner below you, pulling hose from side of cleaner; not the back or the front of the cleaner.
STAIR CLEANING HOSE (Only on Certain Models) WARNING: Never position any cleaner on the stairs as this could damage the carpet. Some models will come complete with an extra bonus hose which is ideal for cleaning stairs. HOW TO ASSEMBLE AND USE Step 1 - Remove the hose attached to the cleaner. WARNING Always work with the cleaner below you, pulling hose from side of cleaner; not the back or the front of the cleaner. Ensure it is positioned sideways up against the bottom step.
HOW TO MAINTAIN The instructions in this booklet serve as a guide to routine maintenance. To avoid unnecessary service calls, check the bag, belt, and brush roll often. Check and Clear Hose Blockages Low suction or poor pickup may be due to a blockage in the vacuum cleaner. 1. Remove hose and check suction at end of hose - if little or no suction, check disposable dust bag. Change if needed. If no improvement proceed to Step 2.
How to Check and Clear Blockages in Base 1. Remove the attachment hose from the lower hose retainer and look into the hose retainer for any obstructions. Proceed to Step 2 to check for any other blockages. 2. Remove the hood by loosening the two screws located on the top of the hood and lifting upward. Upright Position Operating Position s Lowest Position for cleaning under furniture 3. Step on the handle release and lower the handle all the way to the floor. 4.
Brush Roll The brush roll turns as it sweeps and combs the carpet nap. Remove hair and threads from the brush roll so it continues brushing the carpet. To maintain the most efficient cleaning, the bristles must touch the carpet. To test the bristle length, hold a ruler against the underneath side of the cleaner. If the bristles no longer touch the ruler, replace the brush roll. 5 Brush Roll Belt The brush roll belt turns the brush roll to agitate, sweep, and comb the carpet nap.
NOTE: Turn off the switch and unplug the electrical cord before changing dust bag. Never operate the vacuum cleaner without the dust bag or the filter. NOTE: Style AA Filteraire bags must be used to maintain HEPA grade filtration and prolong the life of the HEPA filter. NOTE: Models without HEPA filter option, may use Style AA bags rather than Style AA Filteraire. It may be more convenient to lower the handle to the floor before changing the bag.
Rinsing Directions for Rinsable Filters - Filter can be rinsed up to 6 times. Replace after 6 rinsings to retain filtration level performance from your vacuum. 1. Remove soiled filter from cleaner. 2. Examine filter on both sides. 3. Gently rinse both sides of the filter with warm tap water to remove surface dirt. DO NOT COMPLETELY SOAK FILTER. DO NOT USE SOAP OR DETERGENT. 4. Let the filter dry for at least 12-24 hours. FILTER MUST BE 100% DRY FOR PROPER PERFORMANCE.
HEPA Cartridge Filters and Washable Hepa Filters. (Only for models with HEPA cartridge.) Check the HEPA filters each time the dust cup is emptied. Replace twice a year or after every six times the dust cup is emptied. To remove HEPA cartridge filters and Washable HEPA Filters Latch 1. Push down latch and pull filter cassette back. 2. Then lift filter up and remove. Filter Cartridge (One complete unit) To replace HEPA cartridge filters and Washable HEPA Filters 1.
PROBLEM SOLVING NOTE: Turn off the switch and unplug the electrical cord before servicing. PROBLEM CAUSE SOLUTION Motor will not start. 3 Electric Plug Push plug securely into outlet. Try another outlet. Check circuit breaker. Motor suddenly stops. 3 Thermal Cut Off Refer to page 7. 3 Disposable Dust Bag and filter(s) 3 Cyclonic Cassette 3 3 Belt Brush Roll 3 Hose Change the bag.
Questions? Call Electrolux Customer Care on 08706 055 055 Accessory Items in This Carton 1 crevice tool 1 combination tool 1 wand 1 hardware package (2 screws) 1 hose assembly 1 vacuum cleaner handle Thank you for selecting an Electrolux cleaner. Don’t Forget to Use Genuine Electrolux Bags and Belts Part No. 70306D (3/05) Printed in U.S.A.