INSTRUCTION BOOKLET INTEGRATED COOKER HOOD ZB 350
Thank you for buying a Zanussi product. To enable you to use your appliance effectively and safely, please read this instruction book carefully before using the appliance and retain for future reference. If you require guidance in the use of the appliance or require further information on Zanussi Products, please contact our Customer Care Department. For general enquiries concerning your Zanussi appliance or for further information, visit our website at http:\\www.zanussi.co.
IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. Your safety is of paramount importance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Installation • Child Safety Any installation work must be undertaken by a qualified electrician or a competent person.
YOUR APPLIANCE OPERATING INSTRUCTIONS This cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. To obtain the best performance it is advisable to switch on the hood a few minutes before you start cooking and leave it running for approximately 15 minutes after finishing. Cooker Hood Controls I. Automatic Microswitch The microswitch overrides the controls, and switches off the hood when the visor is closed.
The appliance can be installed to recirculate or extract contaminated air. Recirculation The hood is supplied specified for use in the recirculation mode with the charcoal filter fitted. The contaminated air is cleaned by passing through the filters and then back into the kitchen. Extraction The contaminated air enters the hood passing through the grease filter and out through the ducting into the atmosphere. When the extraction mode is selected the charcoal filter is not required.
MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. The cooker hood must be kept clean, as a build up of grease or fat can be a fire hazard. External Cleaning Wipe the cooker hood frequently with warm soapy water using a mild detergent. Always wear protective gloves when cleaning the hood. Never use scouring pads or abrasive cleaners. Never use excessive amounts of water when cleaning particularly around the control panel.
Synthetic Paper Grease Filter The filter has saturation indicators, which are small squares made from a series of dots. When the white paper inside the squares becomes saturated with grease the coloured dots start to run and spread across the paper, indicating that the filter has reached saturation point and must be replaced. The synthetic paper grease filter cannot be cleaned. It must not be washed. To Replace the Synthetic Paper Grease Filter 1. Open the visor. 2.
SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Solution Symptom The cooker hood will not start • Check the hood is connected to the electricity supply. • Check that the fan speed control is set to 1, 2 or 3. The cooker hood is not working effectively • The fan speed is set high enough for the task. • The grease filter is clean. • The kitchen is adequately vented to allow the entry of fresh air.
PEACE OF MIND FOR TWENTY FOUR MONTHS STANDARD GUARANTEE CONDITIONS We, Zanussi Ltd.
INSTALLATION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way.
INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air. Incorrect installation may affect the safety of this cooker hood. Installation Requirements Before installation check the wall to which the cooker hood is to be fitted for electric cables, water pipes or gas.
Clearance Height A minimum clearance height of 650mm (25 1/2 ”) is required when installed above a built-in electric hob, or 700mm (27 1/2 ”) when installed above a built-in gas hob. A minimum clearance height of 685mm (27”) is required when installed above a slot-in electric cooker, or 787mm (30 1/2 ”) when installed above a slot-in gas cooker.
Venting The hood is more effective when used in the extraction setting (ducted to the outside). Venting kits may be purchased through your retailer or DIY store, and must be ducted to an outside vent of 100mm (4”) minimum. The ducting used must be manufactured from fire retardant material. When the hood is ducted externally the charcoal filter must be removed and the slider control must be in the ducting position. To Fit the Ducting 1.
Fitting the Cooker Hood to the Wall 1. Fit the brackets with the round ends facing downwards using the plastic rawl plugs and screws provided. 2. Once the brackets are secured, lift the hood squarely to the wall slightly higher than the brackets. Lower the cooker hood until it is located onto the two brackets. Ensure that the cooker hood is correctly located before letting go. 3. Access to the two wall levelling screws is from above the hood.
Failure to align the top edge of the decor panel with the template will prevent the visor from opening when installed. 3. 4. Before drilling, use a tape measure to check the distances of the screw holes (as given on the template). The template may have altered due to dampness after manufacture. Use the 6 x 15mm (1/2 ins) round headed screws provided to attach the decor panel to the hood visor. To Refit the Hood with Decor Panel Attached 1.
© Electrolux Household Appliances Limited 2000 4324167 03 - 270300
