EN User manual Refrigerator ZBA7230A 2
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Operation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 3 4 4 4 Care and Cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Environmental conc
or damaged power plug may overheat and cause a fire. 3. Make sure that you can come to the mains plug of the appliance. 4. Do not pull the mains cable. 5. If the power plug socket is loose, do not insert the power plug. There is a risk of electric shock or fire. 6. You must not operate the appliance without the lamp cover1) of interior lighting. • This appliance is heavy. Care should be taken when moving it.
Switching off Temperature regulation • • • • The temperature is automatically regulated. To operate the appliance, proceed as follows: • turn the Temperature regulator toward lower settings to obtain the minimum coldness. • turn the Temperature regulator toward higher settings to obtain the maximum coldness. Important! If the ambient temperature is high or the appliance is fully loaded, and the appliance is set to the lowest temperatures, it may run continuously causing frost to form on the rear wall.
set the Temperature Regulator toward warmer settings to allow automatic defrosting and so a saving in electricity consumption.
• remove all food • defrost 3)and clean the appliance and all accessories • leave the door/doors ajar to prevent unpleasant smells. If the cabinet will be kept on, ask somebody to check it once in a while to prevent the food inside from spoiling in case of a power failure. What to do if… Warning! Before troubleshooting, disconnect the mains plug from the mains socket. Only a qualified electrician or competent person must do the troubleshooting that is not in this manual.
Problem Possible cause Solution The door is not closed correctly. Refer to "Closing the door". The product temperature is too high. Let the product temperature decrease to room temperature before storage. Many products are stored at the same Store less products at the same time. time. There is no cold air circulation in the appliance. Replacing the lamp Caution! Disconnect the plug from the mains socket. 1. Remove the screw from the lamp cover. 2. Remove the lamp cover (refer to the illustration).
Climate class The appliance must be earthed. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a qualified electrician. The manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with the E.E.C. Directives.
2 I 4mm 1 44mm I Install the appliance in the niche. Push the appliance in the direction of the arrows (1) until the upper gap cover stops against the kitchen furniture. Make sure that the distance between the appliance and the cupboard front-edge is 44 mm. Push the appliance in the direction of the arrows (2) against the cupboard on the opposite side of the hinge. Make sure that the clearance between the appliance and the cupboard is 4 mm.
8 mm 8 mm Ha Ha Hc K Ha Hb Push the part (Hc) on the part (Ha). Open the appliance door and the kitchen furniture door at an angle of 90°. Insert the small square (Hb) into guide (Ha). Put together the appliance door and the furniture door and mark the holes. Remove the brackets and mark a distance of 8 mm from the outer edge of the door where the nail must be fitted (K). Hb Place the small square on the guide again and fix it with the screws supplied.
www.zanussi.
