EN User manual Fridge-Freezer ZBB28440SA
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 5 6 What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 Environmental concerns _ _ _ _ _ _ _ _ _ _ _ _ _ _ 13 Subject to change without notice.
. • • • • Make sure that you can come to the mains plug of the appliance. 4. Do not pull the mains cable. 5. If the power plug socket is loose, do not insert the power plug. There is a risk of electric shock or fire. 6. You must not operate the appliance without the lamp cover (if foreseen) of interior lighting. This appliance is heavy. Care should be taken when moving it.
Switching on Insert the plug into the wall socket. Turn the Temperature regulator clockwise to a medium setting. Switching off To turn off the appliance, turn the Temperature regulator to the "O" position. Temperature regulation The temperature is automatically regulated. To operate the appliance, proceed as follows: • turn the Temperature regulator toward lower settings to obtain the minimum coldness. • turn the Temperature regulator toward higher settings to obtain the maximum coldness.
Important! Do not use metallic instruments to remove the trays from the freezer. Cold accumulators The freezer contains at least one cold accumulator which increases storage time in the event of a power cut or breakdown. Positioning the door shelves To permit storage of food packages of various sizes, the door shelves can be placed at different heights. Movable shelves The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired.
• lean foods store better and longer than fatty ones; salt reduces the storage life of food; • water ices, if consumed immediately after removal from the freezer compartment, can possibly cause the skin to be freeze burnt; • it is advisable to show the freezing in date on each individual pack to enable you to keep tab of the storage time.
2. 3. Remove any stored food, wrap it in several layers of newspaper and put it in a cool place. 6. Caution! Do not touch frozen goods with wet hands. Hands can freeze to the goods. Warning! Never use sharp metal tools to scrape off frost from the evaporator as you could damage it. Do not use a mechanical device or any artificial means to speed up the thawing process other than those recommended by the manufacturer.
Problem Possible cause Solution The door has been opened too frequently. Do not keep the door open longer than necessary. The product temperature is too high. Let the product temperature decrease to room temperature before storage. The room temperature is too high. Decrease the room temperature. Water flows on the rear plate of the refrigerator. During the automatic defrosting process, frost defrosts on the rear plate. This is correct. Water flows into the refrigerator.
Remove the screw from the lamp cover. Remove the lamp cover (refer to the illustration). Replace the used lamp with a new lamp of the same power and specifically designed for household appliances (the maximum power is shown on the lamp cover). Install the lamp cover. Tighten the screw to the lamp cover. Connect the plug to the mains socket. Open the door. Make sure that the light comes on. Closing the door 1. 2. 3. Clean the door gaskets. If necessary, adjust the door. Refer to "Installation".
Positioning Install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance: Climate class Ambient temperature SN +10°C to + 32°C N +16°C to + 32°C ST +16°C to + 38°C T +16°C to + 43°C Electrical Connection Caution! Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. Warning! This appliance must be earthed.
• Loosen the upper pin and remove the spacer. • Remove the upper pin and the upper door. • Loosen the middle hinge. • Remove the lower door. • Loosen the lower pin. On the opposite side: • Install the lower pin. • Install the lower door. • Tighten the middle hinge. • Install the upper door. • Tighten the spacer and tighten the upper pin. Ventilation requirements The airflow behind the appliance must be sufficient. x 5 cm 2 min. 200cm2 x 1 min.
GH Ha Hb I 4mm 44mm I 3 Adjust the appliance in 4 Attach the appliance to the niche with 4 screws. the niche. Make sure that the distance between the appliance and the cupboard front-edge is 44 mm. The lower hinge cover (in the accessories bag) makes sure that the distance between the appliance and the kitchen furniture is correct. Make sure that the clearance between the appliance and the cupboard is 4 mm. Open the door. Put the lower hinge cover in position.
8 mm 8 mm K Ha Hb Ha 11 Open the appliance door and the kitchen furniture door at an angle of 90°. Insert the small square (Hb) into guide (Ha). Put together the appliance door and the furniture door and mark the holes. 12 Remove the brackets and mark a distance of 8 mm from the outer edge of the door where the nail must be fitted (K). Do a final check to make sure that: • All screws are tightened. • The magnetic sealing strip is attached tightly to the cabinet.
222301066-A-452011 www.zanussi.
