FREEZER ZBF 7226 INSTRUCTION BOOKLET 2223 383-23
WARNINGS It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings.
• Do not place carbonated or fizzy drinks in the freezer as it creates pressure on the container, which may cause it to explode, resulting in damage to the appliance. Do not use a mechanical device or any artificial means to speed up the thawing process other than those recommended by the manufacturer. Never use metal objects for cleaning your appliance as it may get damaged. Installation • During normal operation, the condenser and compressor at the back of the appliance heat up considerably.
USE Do not use detergents or abrasive powders, as these will damage the finish. Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Control panel A ABCD- B C Appliance button ON/OFF Temperature and function indicator Function button Freezer Thermostat control knob DISPLAY 1 1. 2. 3. 4.
Operation Activation of functions After plugging the plug into the power outlet, if the display is not illuminated, press key (A), appliance on. Each time key C is pressed, the following functions are activated in a clockwise direction: As soon as the appliance is turned on, the following signals will appear on the control panel: Symbol 4 : rapid freezing function. • symbol (2) will be positive, indicating that the temperature is positive.
Excessive temperature alarm An increase in the temperature in the freezer compartment (for example due to an electricity outage) is indicated by: - flashing temperature; - freezer compartment flashing (symbol 2); - red illumination of display; - sounding of buzzer. - alarm symbol. When normal conditions are restored: - the acoustic signal shuts off; - the temperature value continues to flash; - the display illumination remains red.
• not open the door frequently or leave it open longer than absolutely necessary. • Once defrosted, food deteriorates rapidly and cannot be refrozen. • Do not exceed the storage period indicated by the food manufacturer. MAINTENANCE Unplug the appliance before carrying out any maintenance operation. Warning This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must therefore only be carried out by authorized technicians.
INSTALLATION Location The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. For buiding into the kitchen units follow the special “Building-in” instructions given. Attention It must be possible to disconnect the appliance from the mains power supply; the plug must therefore be easily accessible after installation.
Instructions for totally built-in appliances min. 2 200 cm 50 mm Dimensions of the recess Height (1) 1780 mm Depth (2) 550 mm Width (3) 560 mm min. 200 cm2 D567 For safety reasons, minimum ventilation must be as shown in Fig. 540 50 3 Attention: keep ventilation openings clear of obstruction. Furthermore, it is necessary that the niche is provid with a conduct of ventilation having the following dimensions: depth 50 mm width 540 mm 2 1 PR01 13mm Ø 2,5 Drill the unit using a Ø 2.
Fasten the appliance with 4 screws provided in the kit included with the appliance. I I Press in the joint covers between the appliance and the kitchen unit. D724 From the plastic cover (E), which is used to cover the hinge with the pivot pin, you must take away the part as indicated in the drawing. This operation is made easer since there is, in the internal part of the cover hinge lid a groove that facilates the removal of this coomponent.
ca. 50 mm Place guide (Ha) on the inside part of the furniture door, as shown in the figure and mark the position of external holes. After having drilled holes, fix the guide with the screws supplied. 90° 21 m m ca. 50 mm 21 m m Fix cover (Hc) on guide (Ha) until it clips into place. Ha Hc PR33 Open the appliance door and the furniture door at 90°. Insert the small square (Hb) into guide (Ha). Put together the appliance door and the furniture door and mark the holes as indicated in the figure.
www.electrolux.