User manual Dishwasher ZDI430
Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance.
Safety information In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features.
Installation • Check your dishwasher for any transport damage. Never connect a damaged machine. If your dishwasher is damaged contact your supplier. • All packaging must be removed before use. • Any electrical and plumbing work required to install this appliance must be carried out by a qualified and competent person. • For safety reasons it is dangerous to alter the specifications or attempt to modify this product in any way.
1. 2. 3. 4. 5. 6. 7. Up and down programme selection buttons Half load button Delay start button Digital display Indicator lights On/Off button Function buttons Setting mode Press the On/Off button; if the On/Off indicator light illuminates, the indicator lights of the programme selection buttons are illuminated and in the digital display are visible 2 horizontal lines (- -) the appliance is in setting mode.
Up and down programme selection buttons 6 Using these two buttons you have an increasing or a decreasing order in the selection of the programme (see "Washing programmes" chart for the number of the programme). • Starting the washing programme: 1. Press the On/Off button. The On/Off light will illuminate and the indicator lights of the programme selection buttons will illuminate and in the digital display are visible 2 horizontal lines (-). 2.
Half load button The option must be linked to the selection of a washing programme. (See "Programme table" chart). When selected, the corresponding light illuminates. Load dishes in both baskets (lower and upper). When using the option reduce the dosage of detergent which is normally used for a complete load. Delay start button This option allows the start of the programme to be delayed from 1 to 19 hours.
Indicator lights End of programme Illuminates when the washing programme has ended. It also has added functions of visual signalling as: • the setting of the water softener, • intervention of an alarm due to the malfunction of the machine. Salt refilling 1) Illuminates when special salt needs to be filled. It can remain illuminated several hours after the salt has been filled. Rinse aid Illuminates when rinse aid needs to be filled.
Programme Half load Degree of soil Type of load Programme description 4 Quick 30 min. 65° No Light soil Crockery and cutlery Main wash Final rinse 5 Bio 50° Yes Normal soil Crockery and cutlery Prewash Main wash 1 intermediate rinse Final rinse Drying 6 Glass 45° No Normal soil Delicate crockery and glassware Main wash 1 intermediate rinse Final rinse Drying 2) 4) 3) 1) When the Half load button is pressed, the prewash phase will be automatically excluded.
– Set the water hardness to level 1. When using tablets that integrate rinse aid and detergent: IMPORTANT! there is no need to fill up with rinse aid – set the water softener – add special (dishwasher) salt When using tablets that integrate rinse aid, detergent, salt function and other additives: there is no need to fill up with special salt or rinse aid. Check whether these detergents are suitable for your water hardness. Follow the manufacturers instructions.
Water hardness Adjusting the water hardness setting Use of salt °dH °TH mmol/l manually electronically 29 - 36 51 - 64 5,1 - 6,4 2 level 7 yes 23 - 28 40 - 50 4,0 - 5,0 2 level 6 yes 19 - 22 33 - 39 3,3 - 3,9 2 level 5 yes 15 - 18 26 - 32 2,6 - 3,2 1 level 4 yes 11 - 14 19 - 25 1,9 - 2,5 1 level 3 yes 4 - 10 7 - 18 0,7 - 1,8 1 level 2 yes <4 <7 < 0,7 1 level 1 no The water softener must be set in both ways: manually, using the water hardness dial and electro
changes. (For the selection of the new level see the chart). Examples: if the current level is 5, by pressing function button A once, level 6 is selected. if the current level is 10, by pressing function button A once, level 1 is selected. 5. To memorise the operation, switch off the dishwasher by pressing the On/Off button. Filling with dishwasher salt CAUTION! Use only special salt suitable for dishwashers. Unscrew the cap.
Filling with rinse aid Open the lid. Fill up with rinse aid. The Clean up any rinse aid maximum level for filling is which overflows. Close the lid and press until it indicated by "max" locks. IMPORTANT! CAUTION! Top up the rinse aid when the light on the control panel Never fill the rinse aid dispenser with any other subilluminates. stances (e.g. dishwasher cleaning agent, liquid detergent). This would damage the appliance.
Load cutlery and dishes Sponges, household cloths and any object that can absorb water may not be washed in the dishwasher. • Before loading the dishes, you should: – Remove all left over food and debris. – Soften remnants of burnt food in pans • When loading the dishes and cutlery, please note: – Dishes and cutlery must not impede the rotation of the spray arms. – Load hollow items such as cups, glasses, pans, etc. with the opening downwards so that water cannot collect in the container or a deep base.
Load cutlery. For best results we recommend you to use the cutlery grid provided (if the size and dimensions of the cutlery allow it) Place knives and other items of cutlery with sharp points or edges with their handles facing upwards. Risk of injury! Load the lower basket. Arrange serving dishes and large lids around the edge of the basket. The two rows of prongs on the lower basket can be easily lowered to allow you to load pots, pans and bowls. Load upper basket. Light items (plastic bowls etc.
Adjusting the height of the upper basket If washing very large plates you can load them in the lower basket after moving the upper basket to the higher position. Maximum height of the dishes in : upper basket lower basket With upper basket raised 20 cm 31 cm With upper basket lowered 24 cm 27 cm To move to the higher position proceed as follows: 1. Pull out the basket until it stops. 2. Carefully lift both sides upwards until the mechanism is engaged and the basket is stable.
Open the lid. Fill in the detergent in compartment A. Observe the dosing levels. For programmes with pre- When using detergent Close the lid. wash add an additional tablets: place detergent detergent dose in comtablets in compartment A. partmentB. Detergent tablets Detergent tablets from different manufacturers dissolve at different rates. For this reason, some detergent tablets do not attain their full Unloading the dishwasher • Hot dishes are sensitive to knocks.
Care and cleaning Cleaning the filters IMPORTANT! NEVER use the dishwasher without filters. Incorrect repositioning and fitting of the filters will produce poor washing results. Clean filters A, B and C Turn the handle about 1/4 Remove filter A from the thoroughly under running turn anticlockwise and re- base of the washing comwater. move filters B and C. partment.
Internal cleaning Ensure that the seals around the door, the detergent and rinse aid dispensers are cleaned regularly with a damp cloth. We recommend every 3 months to run the wash programme for heavy soiled dishes using detergent but without dishes. Prolonged periods of nonoperation If you are not using the machine for any prolonged period of time you are advised to: 1. Unplug the appliance and then turn off the water. 2. Leave the door ajar to prevent the formation of any unpleasant smells. 3.
by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local coun- cil, your household waste disposal service or the shop where you purchased the product. The dishwasher will not start or stops during operation. Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the indications described in the chart, without calling out an engineer.
If the malfunction or fault code reappears contact the Service Force Centre. For other fault codes not described in the above chart, please contact your Service Force Centre. Contact your local Service Force Centre, quoting the model (Mod.), product number (PNC) and serial number (S.N.). This information can be found on the rating plate located on the side of the dishwasher door.. So that you always have these numbers at hand, we recommend you to make a note of them here: Mod. :. . . . . . . . . . . . . .
Consumption values iations of the power supply and the amount of dishes. The consumption values are intended as a guide and depends on the pressure and the temperature of the water and also by the var- Consumption values Programme Programme duration (in Energy consumption (in minutes) kWh) Water (litres) 1 Rinse and Hold 12 0,1 4 2 Intensive 70° 80-90 1,6-1,8 22-24 3 Auto 45°-70° 90-140 1,1-1,8 12-23 4 Quick 30min.
Full load: 12 standard place settings Amount of detergent required 5 g + 25 g (Type B) Rinse aid setting position 4 (Type III) Upper basket Cutlery basket Lower basket cup racks: position A Installation WARNING! Any electrical and/or plumbing work required to install this appliance should be carried out by a qualified electrician and/or plumber or competent person. however, depends on how the hot water is produced.
Water inlet hose with safety valve Connect the inlet hose to a water tap with an external thread of 3/4”. After connecting the double-walled water inlet hose, the safety valve is next to the tap. If the water inlet hose leaks, the safety valve cuts off the water supply. WARNING! The electrical cable for the safety valve is in the double-walled water inlet hose and is live. Therefore do not immerse the water inlet hose or the safety valve in water. Take care when installing the water inlet hose .
be no smaller than the diameter of the hose provided. CAUTION! To avoid water leakage after installation make sure that the water couplings are tight. Electrical connection CAUTION! Safety standards require the appliance to be earthed. Prior to using the appliance for the first time, ensure that the rated voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed. The fuse rating is also to be found on the rating plate.
www.electrolux.