User Manual GETTING STARTED? EASY.
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference.
• • • • • Do not keep the appliance door open without supervision to prevent to fall on it. Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. Do not use water spray and steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet. The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused.
DISPOSAL WARNING! Risk of injury or suffocation. • • • 4 Disconnect the appliance from the mains supply. Cut off the mains cable and discard it. Remove the door catch to prevent children and pets to get closed in the appliance.
EASY START 2 1 5 1 On/off button 2 Programme indicators 3 4 4 Programme button 5 Half load button 3 Indicators INDICATORS Running programme indicator. It comes on when the programme starts and goes off when the programme is completed. End indicator. Salt indicator. It is always off while the programme operates.
Consumption values 1) Programme Degree of soil Type of load Programme phases Duration (min) 4) 5) Fresh soil Crockery and cutlery • All Energy (kWh) Water (l) 30 0.9 9 • Wash 60 °C or 65 °C Rinses • Prewash 14 0.1 4 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values.
Press the programme button until all programme indicators are on (Programme selection mode). With this function you can cancel the running programme. USER MODE While the appliance is in programme selection mode: 1. Press and hold programme button until the indicator starts to flash and the indicator In user mode can be changed: • The level of the water softener according to the water hardness. • The activation or the deactivation of the acoustic signal for end of programme.
German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Factory setting 2) Do not use salt at this level. ACTIVATING THE ACOUSTIC SIGNAL FOR THE END OF PROGRAMME By default this acoustic signal is deactivated but it is possible to activate it. 1.
working. The washing phase starts only after this procedure is completed. The procedure will be repeated periodically. ADDING SALT Before first use put one litre of water in the salt container. Water and salt can come out from the salt container when you fill it. Risk of corrosion. To prevent it, after you fill the salt container, start a programme. ADDING RINSE AID 1 43 21 A 2 The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot rinse phase.
ADDING MULTI-TABLETS 1 30 20 2 • • • Do not fill the salt container and the rinse aid dispenser. Adjust the water softener to the lowest level. Set the rinse aid dispenser to the lowest position. STARTING A PROGRAMME 1. Keep the appliance door ajar. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. 3. Press the programme button until the indicator of the programme you want to set comes on. 4.
END OF THE PROGRAMME • • Press the on/off button to deactivate the appliance. Close the water tap. If you do not press the on/off button, after few minutes from the end of the programme all the indicators go off. This helps to decrease the energy consumption. HINTS AND TIPS GENERAL The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • Remove larger residues of food from the dishes into the waste bin. • Do not pre-rinse dishes by hand.
WHAT TO DO IF YOU WANT TO STOP USING MULTI-TABLETS Before you start to use separately detergent, salt and rinse aid do the following procedure. 1. Set the highest level of the water softener. 2. Make sure that the salt and rinse aid containers are full. 3. Start the shortest programme with a rinsing phase. Do not add detergent and do not load the baskets. 4. When the programme is completed, adjust the water softener according to the water hardness in your area. 5. Adjust the released quantity of rinse aid.
C • • • • Make sure that there are no residues of food or soil in or around the edge of the sump. Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides. Reassemble the filters (A) and (B). Put back the filter (A) in the flat filter (C). Turn it clockwise until it locks. An incorrect position of the filters can cause bad washing results and damage to the appliance CLEANING THE SPRAY ARMS Do not remove the spray arms.
Problem and alarm code Possible solution The programme does not start. • • Make sure that the appliance door is closed. The appliance has started the procedure to recharge the resin inside the water softener. The duration of the procedure is approximately 5 minutes. The appliance does not fill with water. • The end indicator flashes 1 time intermittently. • Acoustic signal sounds 1 time intermittently. • • Make sure that the water tap is open.
TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 596 / 818-898 / 555 Electrical connection 1) Voltage (V) 220 - 240 Frequency (Hz) 50 Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 13 Power consumption Left-on mode (W) 0.50 Power consumption Off-mode (W) 0.50 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy, (e.g.
100006970-A-492014 WWW.ZANUSSI.