GB User manual Dishwasher ZDT41 2
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Washing programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Use of the appliance _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Setting the water softener _ _ _ _ _ _ _ _ _ _ _ _ _ Use of dishwasher salt _ _ _ _ _ _ _ _ _ _ _ _ _ _ Use of rinse aid _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Loading cutlery and dishes _ _ _ _ _ _ _ _ _ _ _ _ Use of detergent _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 3 4 5 5 6 7 8 9 Setting and starting
• Do not change the specifications or modify this product. Risk of injury and damage to the appliance. • Do not use the appliance: – if the mains cable or water hoses are damaged, – if the control panel, worktop or plinth area are damaged, that you can get access to the inner side of the appliance. Contact your local Service Force Centre. • Do not drill into the sides of the appliance to prevent damage to hydraulic and electrical components.
Setting mode The appliance is in setting mode when all the programme indicator lights are off and the end indicator light flashes. The appliance must be in setting mode for these operations: – To set a washing programme. – To set the water softener level. – To deactivate/activate the audible signals. If a programme indicator light is on, cancel the programme to go back to the setting mode. Refer to the chapter "Setting and starting a washing programme".
Programme Degree of soil Any Type of load Programme description Partial load (to be completed later in the day) 1 cold rinse (to avoid food scraps from sticking). This programme does not require the use of detergent). 1) This is the perfect daily programme to clean a not fully load. Ideal for a family of 4 persons who only want to load breakfast and dinner crockery and cutlery. 2) Test programme for test institutes. Please refer to separate leaflet supplied, for test data.
Water hardness Water hardness setting °dH °TH mmol/l Clarke manually electronically 51 - 70 91 - 125 9,1 - 12,5 64 - 88 2 10 43 - 50 76 - 90 7,6 - 9,0 53 - 63 2 9 37 - 42 65 - 75 6,5 - 7,5 46 - 52 2 8 29 - 36 51 - 64 5,1 - 6,4 36 - 45 2 7 23 - 28 40 - 50 4,0 - 5,0 28 - 35 2 6 19 - 22 33 - 39 3,3 - 3,9 23 - 27 2 5 15 - 18 26 - 32 2,6 - 3,2 18 - 22 1 4 11 - 14 19 - 25 1,9 - 2,5 13 - 17 1 3 4 - 10 7 - 18 0,7 - 1,8 5 - 12 1 2 <4 <7 < 0,7 <5 11)
It is normal that water overflows from the salt container when you fill it with salt. Make sure that there is no grain of salt outer of the salt compartment. Salt which stays on the tank for a while drills the tank. It is recommended to start a washing programme immediately after you fill the salt container. This prevents of corrosion because of spilled salt. 1 3 Fill the salt container with 1 litre of water (only the first operation). 2 Important! Fill the salt container from time to time.
AX + M Caution! Do not fill the rinse aid dispenser with other products (e.g. dishwasher cleaning agent, liquid detergent). This can cause damage to the appliance. 1 2 3 Adjusting the dosage of rinse aid 4 4 AX 2 3 4 The rinse aid dial is set at the factory at position 3. To increase or decrease the dosage refer to 'What to do if...' AX + M M 1 Fill when the rinse aid indicator ( B ) becomes clear.
Warning! Adjust the height before you load the upper basket. Maximum height of the dishes in : upper basket lower basket Upper position 20 cm 31 cm Lower position 24 cm 27 cm 2 1 Use the cutlery grid. If the dimensions of the cutlery prevent use of the cutlery grid, remove it. 1 1 Arrange the items to let water touch all surfaces. 2 For longer items fold the cup racks up. Prevent to put plates in the first three sections in the front part of the upper basket. Make sure the plates tilt forward.
• other cleaning agents. Do these steps to use detergent tablets: 1. Make sure that the detergent tablets are applicable for your water hardness. Refer to the instructions from the manufacturer. 2. Set the lowest levels of water hardness and rinse aid dosage. 4 3 Fill the detergent dispens- If you use a washing proer (A) with detergent. gramme with prewash phase, put more detergent in the prewash detergent compartment (B). It is not necessary to fill the salt container and the rinse aid dispenser.
2. Release the programme selection/cancel button to cancel the washing programme. At this time you can do these steps: 1. Switch off the appliance. 2. Set a new washing programme. Fill the detergent dispenser with detergent before you set a new washing programme. Interrupting a washing programme Open the door. • The programme stops. Close the door. • The programme continues from the point of interruption.
Important! Do not remove the spray arms. Frost precautions If the holes in the spray arms become clogged, remove remaining parts of soil with a cocktail stick. Caution! Do not install the appliance where the temperature is below 0 °C. The manufacturer is not responsible for damage because of frost. External cleaning Clean the external surfaces of the appliance and control panel with a damp soft cloth. Only use neutral detergents.
The cleaning results are not satisfactory The dishes are not clean • The selected washing programme is not applicable for the type of load and soil. • The baskets are loaded incorrectly so that water cannot reach all surfaces. • Spray arms do not turn freely because of incorrect arrangement of the load. • The filters are dirty or not correctly installed. • The quantity of detergent is too little or missing. Limescales particles on the dishes • The salt container is empty.
Warning! To discard the appliance, follow the procedure: • Pull the mains plug out of the socket. • Cut off the mains cable and mains plug and discard them. • Discard the door catch. This prevents the children to close themselves inside the appliance and endanger their lives. Installation Warning! Make sure that mains plug is disconnected from the mains socket during installation. Important! Obey the instructions in the enclosed template to: • Build-in the appliance. • Install the furniture panel.
The internal diameter must not be smaller than the diameter of the hose. If you connect the water drain hose to a trap spigot under the sink, remove the plastic membrane (A). If you do not remove the membrane, remaining food can cause a blockage in the drain hose spigot. Caution! Make sure that the water couplings are tight to prevent water leakage. 3 4 Electrical connection Warning! The manufacturer is not responsible if you do not follow these safety precautions.
www.zanussi.com 156985570-00-042009 To buy accessories, consumables and spare parts at our online shop please visit: www.zanussi.co.
