Instruction booklet Electric hob ZEL 640
Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance.
Contents For the User Description of the Hob ....................................................................................... 3 Important Safety Information .............................................................................. 4 Before the First Use of the Appliance ................................................................. 6 Operation .......................................................................................................... 6 Maintenance and Cleaning .................
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08445 612 612. Installation • This hob must be installed by qualified • • • • personnel, according to the manufacturer’s instructions and to the relevant British Standards. Before carrying out any operation, make sure the appliance is DISCONNECTED from the power supply. Remove all packaging before using the hob.
Environmental information • All the materials used are environmentally friendly and recyclable. Please make your contribution to safeguarding the environment by using the special differentiated waste collection channels. • Appliances that are no longer used or unusable are not worthless waste. Through ecological disposal, various materials used in manufacturing your appliance can be recovered. • Find out about the possibilities of disposal from your specialised dealer or local Council.
Before the First Use of the Appliance ) Before using the appliance remove all packaging, including the advertising labels and any protective film. When using the hob for the first time: 1) place on all the plates a pan filled with some water; 2) switch the plates on for about 10 minutes at “maximum” position until water inside the pans boils; 3) then, turn the control knob to “minumum” and allow the plates to run for approximately 20 minutes; 4) open a window for ventilation.
a red dot, and will heat up more quickly than a normal plate. As the red dots are painted on the plate, they may deteriorate during use and even disappear completely after a period of time. This will not affect the performance of the hob. It is important to note that the plate may smoke and produce a slightly unpleasant odour when used for the first time. This is quite normal and will disappear after a short while.
For the correct use of the hotplates For better efficiency of the electric hotplates and lower electricity consumption: • switch on the hotplates only after placing the pots on them. • For cooking on the electric hotplates it is advisable to use triple-bottom pots of the same width as the cooking zone, or slightly larger (Figure). • Do not use wet pots on the electric hot-plates, and do not place wet lids on the switched off hot-plates, because the moisture and condensate could damage them.
• • • Do not leave a hotplate switched on without a pot or with an empty pot. Do not place a pot on a cold hotplate or leave it to cool on a switched-off hotplate. This could cause damaging condensation to form. For faster cooking and to avoid heat dispersion, it is advisable to use flatbottomed pots, to ensure maximum contact of the bottoms with the cooking zone. • Take care never to lean or reach over a hot electric plate.
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. This appliance cannot be cleaned with steam or with a steam cleaning machine. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added.
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. SYMPTOM SOLUTION The plate does not heat up. Check that the unit is plugged in and the electrical supply is switched on. Check the mains fuse has not blown.
Instructions for the Installer Engineers technical data Heating elements ratings Rapid front left hotplate Ø 180 mm Rapid back left hotplate Ø 145 mm Rapid front right hotplate Ø 145 mm Rapid back right hotplate Ø 180 mm Total rating Voltage tension 1500 W 1000 W 1500 W 2000 W 6000 W 230 V~ 50 Hz Cut out dimensions Width: Depth: 550 mm 470 mm Overall dimensions Width: Depth: 12 580 mm 500 mm
Important safety requirements This hob must be installed in accordance with the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Par. 2 and B.S. 6891 Current Editions. Location This hob has been registered as a "Class X" appliance according to Fire Risk Regulations. Minimum distances detailed below must be observed.
Electrical Connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230 V~ 50 Hz electrical supply. Before switching on, make sure the electricity supply voltage is the same as that indicated on the hob rating plate.
similar characteristics: H05 V2V2-F. The cable has three wires. The earth wire is yellow/green and must be approx. 2 cm longer than the phase and neutral wires (Figure). Fit the cable with a plug suitable for the load and connect it to a suitable safety socket. To connect directly to the mains, a suitable omnipolar switch complying with current standards and with a contact gap of at least 3 mm must be installed between the appliance and the electrical system.
Electrical connection to the terminal box The appliance is fitted with a three pole terminal box whose cables are predisposed for a 230 V monophase function (Figure). The earth wire should be connected to the terminal marked by the sign . After having connected the wire to the terminal secure it with a cable clip. Supply Cable Specifications For Uk use only Connection Min.
Installation The hob must be installed according to the instructions supplied. The hob must be installed by qualified personnel to the relevant British Standards. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. When the hob is first installed Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory.
diagram. When the screws have been tightened, the excess seal can be removed. The edge of the hob forms a double seal which prevents the ingress of liquids.
Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2.
Guarantee/Customer Service Standard guarantee conditions We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: · The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning 08445 616 616 Your telephone call will be automatically routed to the Service Force Centre covering your postcode area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.
European Guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law.
www.zanussi.co.uk 39715-6901 02/10 R.