Contents Instructions for the owner Installation .Page 3 Technical data .Page 3 Use . Page 4 Gas oven . Page 6 Roasting jack .Page 7 Minute minder . Page 8 Cooking procedure . . Page 9 Maintenance & cleaning . . Page 10 Instructions for the installer Installation . . Page 12 Gas connection . . . Page 14 Electrical connection . . Page 14 Replacing the nozzles . . Page 15 Adjusting the air . Page 16 Adjusting the minimum . Page 17 Maintenance. . .
Instructions for the owner of the appliance Installation It is mandatory that all operations required for the installation, the adjustments, the conversion to the type of gas available ete. be carried out by QUALIFIED PERSONNEL in accordance with existing rules and regulations. The relevant instructions are to be found in the special chapter for the installer. This appliance meets the requirements laid down in EEC Directive No 76/889 dated 4/11/1976 relating to the suppression of radio and TV interference.
Care and use Cooker ZG 951 A -Cover B Semi-rapid burner C Rapid burner D Rapid burner E Auxiliary burner F -Control panel G Side grilles H -Grilles 1 -Dripping pan L -Handle M Even door N -Removable base Q) Front panel P Removable drawer 1. Oven light switch 5. Auxiliary burner knob 2. Oven knob 6. Rapid burner knob 3. Lighting button 7.
Cooker ZG 952 A -Cover B Semi rapid burner € Rapid burner D Rapid burner E Auxiliary burner ¥ Control panel G -Side grilles H Grilles 1 Dripping pan L Handle M Oven door N Removable base 0O Front panel P Removable drawer 1. Rotisserie switch 2, Oven light switch 3. Oven knob 4. Lighting button 5. Minute minder 8. Rapid burner knob 7. Auxiliary burner knob 8. Rapid burner knob 9.
Operation Worktop burners T'o light a worktop burner, turn the relevant knob anticlockwise to maximum. Fig.1). After opening the tap to maximum, push bunion marked by a small electric spark. Asg soon a8 the burner is lit, adjust the flame as required.
Gas grill On the model ZG951 to light the grill, strike a mate and hold it close to the grill burner then firmly depress the oven control knob and turn it clockwise to the limit stop; on the model ZG 952 operate on the push button marked by a small spark. Keep the control knob depressed for 10-15 secs; then release the grill control knob. %@\x L A\ Oven safety device The cooker features a thermonuclear; if for any reason the flame should extinguish the device will interrupt the gas flow.
Using the rotisserie {for the model provided) The rotisserie can be used for either spit roasting meat or for kebabs and smaller pieces of meat. The accessories for either are provided. 1f you want to spit roast a large piece of meat or poultry proceed as follows: Firstly place one of the two prong forks anti the spit and lock it into position with the thumb nut. Then skewer the meat or poultry onto the spit and secure onto the fork.
Hints for a correct use of the oven and the grill After turning on the oven and prior to introducing the food, it is advisable to wait for about. 10 to 15 minutes to allow the oven to reach the required temperature. In the case of dishes requiring a high initial temperature or a stabilized temperature at the center of the oven, the above preheating time will have to be reasoned. The food to be cooked should be placed on the oven shelf, dripping-pan (roast meat) or in a baking-tin placed on the shelf.
Maintenance For a long service life of the appliance we strongly recommend that you frequently carry out a thorough cleaning operation. Cleaning the oven {without panels} Always wait until the oven is cool before cleaning. It is advisable to release the oven side rails. All enameled parts should be washed with lukewarm water and detergent without sing abrasive products which might damage them.
Replacing the oven light bulb Disconnect the appliance from the electric supply. Unscrew the bullfight glass protection from the oven. Unscrew the light bulb and replace it with a new bulb suitable for high temperature (300 °C) and having the following technical features: Operating voltage: 240V 50 Hz Power absorbed: 15 W Removing the oven door {Fig. 3 ABO) To thoroughly clean the oven you should remove the door by proceeding as follows: 1.
Instructions for the installer Installation The following instructions are meant fora qualified installer and should assist him tn carrying out all installation, adjustment and maintenance operations in the most correct way and in accordance with existing laws and regulations. Important: Before servicing the appliance or undertaking any maintenance work on it, be sure to disconnect it from the electric supply.
The appliance incorporates a set of adjustable feet. By properly adjusting the feet, the appliance can be setup at the required height and correctly aligned with the kitchen furniture or any other surface, thus ensuring an even spreading out of liquids in pans and pots. These adjustable feet are easily accessible after removing the dish-warming drawer.
Gas connection Connect the cooker to the gas bottle or gas mains, in accordance with existing rules and regulations, only after making sure that the appliance has been duly adapted to the type of gas available. Q Otherwise, carry out all operations recording to the directions to be found under the paragraph "Conversion to other types of gas”.
with the ocker definitely installed, the wall socket or the omnipotent switch can easily be reached. The Manufacturer disclaims any Ability in case these accident-preventing rules are not observed. The heat insulation of the oven and grease residues from the manufacturing process produce smoke and an unpleasant smell during the first minutes of operation. It is therefore advisable, the first time the appliance is used, to per-heat the oven for about 30 mind.
unscrew the nozzles and replace them with the corresponding nozzles (supplied with the cooker) suitable for the new type of gas. Refit the parts reversing the above procedure. Oven burner Undo the securing w and remove the oven bottom; from inside the diminishing drawer unscrew the wing nut securing the bracket carrying the spark 1¢ and the thermonuclear as well as the ime to be found in the front part of the burner; then push the burner itself forwards.
Adjusting the minimum flame setting Worktop burners Turn the gas tap to minimum, remove the control knob and with a screwdriver turn the adjusting screw, which is inside the gas tap shaft, until a small and steady flame is obtained. Check stability of flame by quickly turning the tap from max. to min, readjusting the flame if necessary. Attention: If the cooker is adjusted for Methane gas, to convert it to Liquid gas it will suffice to screw completely in the minimum adjustment screw.
Maintenance *heck at regular intervals the condition and serviceability of the gas connection hose and pressure regulator, if any; in case of malfunction, do not repair but replace the whole faulty part. T'a ensure 8 smooth and safe operation, it 15 necessary o periodically grease the gas aps, Servicing should be carried out as follows: remove the knobs and slide out the front lanes after removing the securing screws, lingerer the two resews to be found next i the gas tap shaft.
ZANINESS! ELECTROMAGNETIC Industries Gaussian spa GAUSSIAN GUARANTEE CONDITIONS This guarantee is in addition to your statutory and other legal rights which will not be excluded or in any way diminished by the return of the enclosed card.
