GAS HOB ÃÀÇÎÂÀß ÂÀÐÎ×ÍÀß ÏÎÂÅÐÕÍÎÑÒÜ ZGF 646 INSTRUCTION BOOKLET ÐÓÊÎÂÎÄÑÒÂÎ ÏÎ ÝÊÑÏËÓÀÒÀÖÈÈ RU
ENGLISH Important Safety Information These warnings are provided in the interest of safety. You MUST read them carefully before installing or using the appliance. During Operation • • • • • • • • It is most important that this instruction book should be retained with the appliance for future reference.
Guide to Use the instructions Contents The following symbols will be found in the text to guide you throughout the Instructions: For the User Safety Instructions Important Safety Information 2 Instruction for the User 3 Cleaning and Maintenance 4 Step by step instructions for an operation Hints and Tips Environmental information For the Installer Technical Data 5 Electrical Connection 6 Adaptation to different types of gas 7 Building In 8 Service and original spare parts " These instru
The Hob Lid (mod. ZGF 646 IX) In order to make the appliance match with the kitchen design, a lid (not provided) can be fitted on the hob. • The lid is meant to avoid dust to settle on the hob, when it is closed, and to collect splashes of oil or fat, when it is open. Do not use it for any other purpose. • Always wipe off any splash of liquid before opening the lid. • Always clean the lid from cooking residues before opening it or taking it off. WARNING! The crystal lid can splinter when overheated.
Technical data Gas Burners Rating Hob recess dimensions Rapid Burner (big) 3,0 kW (G20) - 2,8 kW (G30-G31) Semirapid Burner (medium) 2,0 kW Auxiliary Burner (small) 1,0 kW Class 3 Appliance Category II2H3B/P Setting Natural Gas G20 20 mbar Gas connection G 1/2" Length Width Electric Supply 560 mm. 480 mm. 230 V ~ 50 Hz Instruction for the Installer The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force.
Electrical connection The appliance is designed to be connected to 230 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force.
Adaptation to different types of gas Injector replacement • Remove the pan supports. • Remove the burner's caps and crowns. • With a socket spanner 7 unscrew and remove the injectors (Fig. 7), and replace them with the ones required for the type of gas in use (see table 2). • Reassemble the parts, following the same procedure backwards. • Replace the rating label (placed near the gas supply pipe) with the relevant one for the new type of gas supply.
Building in SR SR A A R SR SR R 58 0 51 0 ZGF 646 IX 580 Fig. 9 51 0 ZGF 646 ITCX A = Auxiliary burner SR = Semirapid burner R = Rapid Burner These hobs can be inserted in a built-in kitchen unit whose depth is between 550 and 600 mm. The hobs dimensions are shown in Fig. 9. Fitting the lid (only mod. ZGF 646 IX) We recommend the lid hinge block are fitted before installing the hob into the worktop. To install the lid onto the hob, proceed as follows: a.
Installation and assembly These hobs can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in Fig. 13. The edge of the cut out must have a minimum distance from the rear wall of 55 mm. If there are side walls, or sides of the furniture unit near the hob, the cut out edges must have a minimum distance of 100 mm. as shown in Fig. 13.
Fig. 16 Fig. 17 480 30 Possibilities for insertion Kitchen unit with door Kitchen unit with oven The hob recess dimensions must comply the indication given in Figs. 17 and 20 and must be provided with brackets to allow a continuous supply of air. To avoid overhating, the building in should be carried out as shown in Figs. 18 e 19. The hob's electric connection and the oven's one must be carried out separately, both for safety reasons and to allow the oven to be easily taken off the unit.
Service and original spare parts This machine, before leaving the factory, has been tested and studied by many experts and specialists, in order to give you the best results. Original spareparts, certified by the product manufacturer and carrying this symbol are only available at our Service Centre and authorized spareparts shops. Any repair work which needs to be carried out should be done with the utmost care and attention.
