EN User manual Hob ZGG62414 IE GB CY
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ Product description _ _ _ _ _ _ _ _ _ _ _ _ _ Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ 2 3 5 5 6 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9 Technical information _ _ _ _ _ _ _ _ _ _ _ _ 13 Environment concerns _ _ _ _ _ _ _ _ _ _ _ 14 Subject t
• Unattended cooking on a hob with fat or oil can be dangerous and may result in fire. • Never try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket. • Do not store items on the cooking surfaces. • Do not use a steam cleaner to clean the appliance. • Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot.
moved from the holder), earth leakage trips and contactors. Gas connection • All gas connections should be made by a qualified person. • Make sure that there is air circulation around the appliance. • The information about the gas supply is on the rating plate. • This appliance is not connected to a device, which evacuates the products of combustion. Make sure to connect the appliance according to current installation regulations. Pay attention to requirements regarding adequate ventilation.
Product description Cooking surface layout 1 2 1 Semi-rapid burner 2 Semi-rapid burner 3 Control knobs 4 Auxiliary burner 5 Rapid burner 5 4 3 Control knobs Symbol Symbol Description ignition position / maximum gas supply Description no gas supply / off position minimum gas supply Daily use Warning! Refer to the Safety chapters. ple to warm up. If not, the gas supply will be interrupted. Adjust the flame after it is regular. Ignition of the burner 3.
A B C D A) B) C) D) Important! In the absence of electricity you can ignite the burner without electrical device; in this case approach the burner with a flame, push the relevant knob down and turn it counter-clockwise to maximum gas release position. If the burner accidentally goes out, turn the control knob to the off position and try to light the burner again after minimum 1 minute. The spark generator can start automatically when you switch on the mains, after installation or a power cut.
Care and cleaning Warning! Refer to the Safety chapters. Warning! Deactivate the appliance and let it cool down before you clean it. Disconnect the appliance from the electrical supply before you do cleaning or maintenance work. Scratches or dark stains on the surface have no effect on how the appliance operates. • You can remove the pan supports to easily clean the hob. • To clean the enamelled parts, cap and crown, wash them with warm soapy water and dry them carefully before you put them back.
Problem Possible cause Remedy • Burner cap and crown are placed uneven • Make sure that the burner cap and crown are in correct positions. The flame is blow out immediately after ignition • Thermocouple is not heated sufficient • After lightning the flame, keep the knob pushed for approximately 5 seconds. The gas ring burns unevenly • Burner crown is blocked with food residues • Make sure that the injector is not blocked and the burner crown is clear of food particles.
Installation Warning! Refer to the Safety chapters. Warning! The gas settings of this appliance are not applicable for Cyprus. If you install this appliance in Cyprus, you must change the nozzles before you connect the appliance. To change the nozzles refer to the type of gas used. See the tables in the “Technical Information” chapter for more information.
3. A B C A) End of shaft with nut B) Washer C) Elbow Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Make sure that the main connection pipe does not exert any strain on the hob.
• The appliance must not be connected with an extension cable, an adapter or a multiple socket. There is a risk of fire. • Do not let the power cable to heat up to a temperature of more than 90° C. The cable should be guided by means of clamps fixed to the side of the cabinet, in order to avoid any contact with the equipment beneath the cooktop. • Make sure that there is access to the mains plug after the installation.
To replace the connection cable use only H05V2V2-F T90 or equivalent type. Make sure that the cable section is applicable to the voltage load and the working temperature. The yellow/green earth wire (B) must be approximately 2 cm longer than the live and neutral wire (A). A B A B A) supplied seal B) supplied brackets Caution! Install the appliance only on a worktop with flat surface.
Technical information Hob dimensions Hob recess dimensions Width: 580 mm Width: 550 mm Length: 500 mm Length: 470 mm Heat input Rapid burner: 3.0 kW Semi-rapid burner: 2.0 kW Auxiliary burner: 1.
NORMAL POWER REDUCED POWER NORMAL POWER NATURAL GAS G20 (2H) 20 mbar BURNER kW Rapid 3.0 (natural gas) 2.8 (LPG) kW 0.75 inj. 1/100 mm 119 m³/h 0.286 LPG (Butane/Propane) G30/G31 (3+) 28-30/37 mbar inj. 1/100 mm 86 G30 28–30 mbar G31 37 mbar g/h g/h 204 200 Gas burners for LPG G30/G31 30/30 mbar - only Cyprus NORMAL POWER kW inj. 1/100 mm Auxiliary BURNER 1.0 50 Semi-rapid 2.0 71 Rapid 2.
www.zanussi.
397226001-B-392012 www.zanussi.