GAS HOB ZGL 62 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation z z z z This appliance must be installed and serviced by a competent person as stated in the Gas Safety ( Installation and Use) Regulations Current Editions and the IEE Wiring Regulations. Remove all packaging before using the hob.
Contents For the Installer For the User Important Safety Information 2 Instructions for the Installer 8 Description of the Hob 4 Installation 10 Operation 5 Electrical connections 12 Maintenance and Cleaning 6 Wiring Diagram 13 Something Not Working? 7 Fault Finding 13 Guarantee/Customer Service 16 Commissioning 15 European guarantee 17 Conversion from Natural Gas to LPG 15 Environmental Information z z z Guide to Use the instructions After installation, please dispose of th
Description of the Hob 3 2 3 1 4 1. 2. 3. 4. 5.
Operation Hob burners ) To light a burner: turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner; z then, check the flame is regular and adjust it as required. If you cannot light the flame even after several attempts, check the "cap" and “crown” (see diagram - letter A and B) are in the correct position. To put the flame out, turn the knob to the symbol z.
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added.
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Zanussi Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee.
Instructions for the Installer Engineers technical data Overall dimensions Width: Depth: Rear Left Burner Heat Input 580 mm 500 mm Front Left Burner (rapid) Heat Input 3.0 kW Natural gas (10236 BTU/HR) 2.8 kW L.P.G. (9554 BTU/HR) Cut out dimensions Width: Depth: (semi rapid) 2.0 kW (6824 BTU/HR) 550 mm 470 mm Supply connections Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Rear Right Burner Heat Input (semi rapid) 2.0 kW (6824 BTU/HR) Front Right Burner Heat Input (auxiliary) 1.
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Provision for ventilation Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Part 2 and B.S. 6891 Current Editions. The hob should not be installed in a bed sitting room with a volume of less than 20 m3.
Installation IMPORTANT: This hob must be installed by a competent person to the relevant Gas Standards. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. Any gas installation must be carried out by a competent person.
Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. 1 ON/OFF SWITCH It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2. 2 3 ON/OFF SWITCH FLEX OUTLET FLEX OUTLET FO 0763 FO 1013 FO 0764 Dimensions are given in mm.
Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230 V 50 Hz AC electrical supply. Before switching on, make sure the electricity supply voltage is the same as that indicated on the hob rating plate.
Wiring Diagram A. TAPS IGNITOR SWITCHES B. IGNITOR UNIT Fault Finding Preliminary Electrical Systems Check Blue START Isolate appliance and carry out: A: Earth Continuity check. Neutral Wire Blue E( ) FUSE Brown SOCKET (face view) PLUG (with cover removed) Earth Wire ( ) Green/Yellow N L Blue Brown Green Yellow YES NO Carry out: C: Polarity check. Has inlet fuse blown? YES NO Inlet wiring faulty. Rectify any fault. Isolate appliance and carry out: B: Insulation check.
Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Light burner manually Check by pass simmer Check polarity and earth continuity of supply point Check position of the electrode Check earth continuity of appliance Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from 'L' on the mains connector block and the taps ignition switches Check continuity from ignition swit
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. ) - - - Re-ignite the burner and set to MIN.
Guarantee/Customer Service Standard guarantee conditions We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: · The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
European guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law.
35675-2603 11/06 Grafiche MDM - Forlì www.zanussi-electrolux.co.