GAS HOB ZGL 646 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance RO
Important Safety Information These warnings are provided in the interest of safety. You MUST read them carefully before installing or using the appliance. About Installation, Cleaning and Maintenance • • • • • • • • It is mandatory that all operations required for the installation are carried out by a qualified or competent person, in accordance with existing rules and regulations. Ensure a good ventilation around the appliance. A poor air supply could cause lack of oxygen.
Contents For the Installer For the User Important Safety Information 3 Instruction for the Installer 8 Instruction for the User 5 Technical Data 9 Cleaning and Maintenance 6 Gas connection 10 Service and original Spare Parts 7 Adaptation to different types of gas 11 Building In 12 Possibilities for insertion 14 Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions Step by step instructions for an opera
Instruction for the User Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. Hob burners control knobs The hob burners control knobs are situated on the hob right hand side. The symbols on the knobs mean that: there is no gas supply there is maximum gas supply there is minimum gas supply Lighting the burners For easier lighting, proceed before putting a pan on the pan support. To light a burner: 1.
Cleaning and Maintenance General cleaning Wash the enamelled components with warm soapy water. Never use abrasive cleaners Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food. Regularly wipe over the hob top using a soft cloth weel wrung out in warm water to which a little liquid detergent has been added.
Service and original Spare Parts This appliance, before leaving the factory, has been tested and studied by many experts and specialists, in order to give you the best results. Original spareparts, certified by the product manufacturer and carrying this symbol are only available at our Service Centre and authorized spareparts shops. Any repair work which needs to be carried out should be done with the utmost care and attention.
Instruction for the Installer The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top. Avoid installing the appliance in the proximity of inflammable materials (e.g. curtains, tea towels etc.).
Technical Data Gas Burners Rating Rapid Burner 3,0 kW (G20) - 2,8 kW (G30/G31) Semirapid Burner 2,0 kW Auxiliary Burner 1,0 kW Appliance Class Category Setting 3 II2H3B/P Natural Gas G20 - 20 mbar Gas connection G 1/2" Hob recess dimensions Length Width 550 mm 470 mm 9
Gas connection Choose fixed connections or use a flexible pipe in stainless steel in compliance with the regulation in force. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. Use the same attention when the hob is combinated with an oven. IMPORTANT - To ensure a correct operation, a saving of energy and the long life of the appliance, the voltage pressure of the appliance must correspond to the recommended values.
Adaptation to different types of gas Injectors replacement • Remove the pan supports. • Remove the burner's caps and crowns. • With a socket spanner 7 unscrew and remove the injectors (Fig. 5), and replace them with the ones required for the type of gas in use (see table 2). • Reassemble the parts, following the same procedure backwards. • Replace the rating label (placed near the gas supply pipe) with the relevant one for the new type of gas supply.
Building In SR SR R A 58 0 This hob can be inserted in a built-in kitchen unit whose depth is between 550 and 600 mm. The hob dimensions are shown in the relevant diagram. The edge of the cut out must have a minimum distance from the rear wall of 55 mm. If there are side walls, or sides of the furniture unit near the hob, the cut out edges must have a minimum distance of 100 mm. Hanging furniture units or hoods must be placed at 650 mm. minimum from the hob.
Fitting the hob to the worktop The hobs can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in Fig. 9. To install the hob, proceed as follows: 1) Remove the pan supports, the burners caps and crowns and turn the hob upside down. 2) Place the sealing gasket (supplied with the hob) on the edges of the cut out: place it exactly on the front and rear edge, taking care that the sealings meet without overlapping; 3) Fix the hob with the relevant screws (Fig. 10).
Possibilities for insertion Kitchen unit with door Kitchen unit with oven Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in Fig. 12. The panel fitted under the hob should be easily removable to allow an easy access if a technical assistance intervention is needed. The hob recess dimensions must comply the indication given in Figs.
From the Electrolux Group. The world’s No.1 choice. 35688-4101 10/04 Grafiche MDM - Forlì The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
