User Manual Gas Hob ZGS 64IX RO EE LT UA
Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance.
Contents For the User Important safety information .............................................................................. 4 Operation .......................................................................................................... 6 Using the hob .................................................................................................... 8 Cleaning and Maintenance ................................................................................ 9 Service and original spare parts ...
Important safety information This warnings has been given for the safety of you and others. We therefore ask you to carefully read the procedures of installing and using this appliance. Installation The work of installation must be carried out by competent and qualified installers according to the regulations in force. • Any modifications to the domestic electrical mains which may be necessary for the installation of the appliance should be carried out only by competent personnel.
• This appliance is not connected to a combustion products evacuation device. It must be installed and connected in accordance with current installation regulations. Particular attention shall be given to the relevant requirements regarding ventilation. • The use of a gas cooking appliance results in the production of heat and moisture in the room in which it is installed.
Operation Before using the appliance remove all packaging, including the advertising labels and any protective film. Hob burner control knobs z The symbols on the knobs mean: = no gas supply = maximum gas supply = minimum gas supply For easier lighting, proceed before putting a pan on the pan support. the burners )PushLighting the relevant knob down and turn it anti-clockwise until it reaches the "maximum" position. Then, check the flame is regular and adjust it as required.
If the burner does not light even after 15 seconds, release the control knob, turn it the "off" position and wait for at least one minute before trying to light the burner again. To switch off burners )To put the flame out, turn the knob to the symbol (z).
Using the hob Practical hints For the correct use of the burners To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used. Rapid Burner diameter 18-26 cm Semi-rapid Burner diameter 12-22 cm Auxiliary Burner diameter 8-16 cm • For easier lighting, proceed before putting a pan on the pan support. • Use only pans or pots with flat bottom. • Take care when frying food in hot oil or fat, as the overheated splashes could easily ignite.
Cleaning and Maintenance Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. This appliance cannot be cleaned with steam or with a steam cleaning machine. The burners z z z z The burner caps and crowns can be removed for cleaning. Wash the burners taps and crowns using hot soapy water, and remove marks with a mild paste cleaner.
z z Should the hob top become heavily soiled, the following products are recommended: - For stainless steel hobs use a proprietary stainless steel cleaner. - For other hobs use Hob Brite or Bar Keepers Friend. Do not leave acid or alkaline substances (e.g. vinegar, salt, lemon juice, etc.) on the cooktop. The Ignition electrode The electric ignition is obtained through a ceramic electrode with a metal electrode.
Technical data Burner gas power Rapid burner Semi-rapid burner Auxiliary burner 3,0 kW (natural gas) - 2,8 kW (liquid gas) 2,0 kW 1,0 kW Category Gas supply Gas connection Electric supply Appliance class II2H3B/P natural gas G20 (2H) / 20 mbar G 1/2" 230 V~ 50 Hz 3 Hob dimensions Width Depth 580 mm 500 mm Cut out dimensions Width Depth 550 mm 470 mm 11
Gas burners NORMAL REDUCED POWER POWER NORMAL POWER BURNER kW NATURAL GAS LPG G20 (2H) - 20 mbar (Butane/Propane) 30 mbar kW g/h inj. 100/mm m3/h inj. 100/mm G30 G31 Auxiliary burner 1,0 0,33 70 0,095 50 73 71 Semi-rapid burner 2,0 0,45 96 0,190 71 145 143 0,75 119 0,285 86 204 200 Rapid burner 3,0 (natural gas) 2,8 (liquid gas) By-pass diameters Burner Auxiliary Semi-rapid Rapid 12 Ø By-pass in 1/100 mm.
Installation • The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. • The appliance must be electrically disconnected before all interventions. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed. • The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top.
Adaptation to different types of gas A. Injectors replacement ) • Remove the pan supports. • Remove the burner's caps and crowns. • With a socket spanner 7 unscrew and remove the injectors (Fig. 7), and replace them with the ones required for the type of gas in use (see table «Gas burners»). • Reassemble the parts, following the same procedure backwards. • Replace the rating label (placed near the gas supply pipe) with the relevant one for the new type of gas supply.
Electrical connection The appliance is designed to be connected to 230 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force.
Building in 3 2 1 4 1. 2. 3. 4. 5. Hob Top Rapid Burner Semi-rapid Burner Auxiliary Burner Control knobs This hob can be inserted in a built-in kitchen unit whose depth is between 550 and 600 mm. The hobs dimensions are shown in Fig. 10. The edge of the cut out must have a minimum distance from the rear wall of 55 mm. If there are side walls, or sides of the furniture unit near the hob, the cut out edges must have a minimum distance of 100 mm. Hanging forniture units or hoods must be placed at 650 mm.
Fitting the hob to the worktop Dimensions are given in millimeters The hobs can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in Fig. 11. To install the hob, proceed as follows: 1) Remove the pan supports, the burners caps and crowns and turn the hob upside down.
Possibilities for insertion Kitchen unit with door Proper arrangements must be taken in designing the forniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in Fig. 13. The panel fitted under the hob should be easily removable to allow an easy access if a technical assistance intervention is needed. Kitchen unit with oven The hob recess dimensions must comply the indication given in Figs.
Service and original spar e parts spare This machine, before leaving the factory, has been tested and studied by many experts and specialists, in order to give you the best results. the problem, the appliance model Mod. Prod. No. (Mod. Mod.), the product number (Prod. No.) Ser. No. and the serial number (Ser. No.) marked on the identification plate. Any repair work which needs to be carried out should be done with the utmost care and attention.
35675-2607 01/08 R.
