INSTRUCTION BOOKLET COOKER HOOD ZHC 916X
Thank you for buying a Zanussi product. To enable you to use your appliance effectively and safely, please read this instruction book carefully before using the appliance and retain for future reference. If you require guidance in the use of the appliance or require further information on Zanussi Products, please contact our Customer Care Department. For general enquiries concerning your Zanussi appliance or for further information, visit our website at http:\\www.zanussi.co.
IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. Your safety is of paramount importance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Installation • Child Safety Any installation work must be undertaken by a qualified electrician or a competent person.
YOUR APPLIANCE OPERATING INSTRUCTIONS This cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. To obtain the best performance it is advisable to switch on the hood a few minutes before you start cooking and leave it running for approximately 15 minutes after finishing. Cooker Hood Controls V1. V2. V3. L. Push to engage the low speed, for use with one burner or simmering. Push to engage the medium speed, for normal cooking up to four pans.
OPERATING INSTRUCTIONS This cooker hood can be used to recirculate or extract contaminated air. Recirculation The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter fitted. The contaminated air is cleaned by passing through the filters and then back into the kitchen. S07_29 The activated charcoal filter absorbs odours arising from cooking. In use it will slowly become saturated in grease and less effective.
MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. The cooker hood must be kept clean, a build up of grease or fat can be a fire hazard. External Cleaning S07_06 The metal casing, grille and chimney should be cleaned at least once a month to keep it looking like new. Wipe over the hood with a soft cloth wrung out in mild soapy water and than dry thoroughly.
MAINTENANCE AND CLEANING To Remove the Charcoal Filter Push inwardly on the two retaining clips to disengage the security fixing and remove. S07_2 This appliance can be a fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended. S07_3 Worktop Lighting The lamps should be replaced with a 220-240V 20W halogen spot lamp. To Remove the Lamps Unscrew the two screws to release the metal surround. Remove a lamp from the holder by pulling the lamp downwards.
SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Solution Symptom The cooker hood will not start • Check the hood is connected to the electricity supply. • Check that the fan speed control is set to 1, 2 or 3. The cooker hood is not working effectively • The fan speed is set high enough for the task. • The grease filter is clean. • The kitchen is adequately vented to allow the entry of fresh air.
PEACE OF MIND FOR TWENTY FOUR MONTHS STANDARD GUARANTEE CONDITIONS We, Zanussi, undertake that if within twenty four months of the date of the purchase this Zanussi built-in appliance or any part there of is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: • • • • • The appliance has been correctly installed and used only on the electrical supply stated
INSTALLATION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way. Technical Information DIMENSIONS HEIGHT (CANOPY): HEIGHT (CHIMNEY): WIDTH (CANOPY): WIDTH (CHIMNEY): GROSS: NET: ELECTRICAL SUPPLY: POWER CONSUMPTION: FAN MOTOR: LAMP: (2x20W) HALOGEN Ø 35 mm GUA SUITABLE FOR INSTALLATION ABOVE: 73 mm 450-850 mm 898 mm Ø200-Ø270 mm 24.
INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air. Incorrect installation may affect the safety of this cooker hood. Installation Requirements Before installation check the wall to which the cooker hood is to be fitted for electric cables, water pipes or gas.
INSTALLING THE COOKER HOOD Clearance Heights The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated, provided the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Specifications. If the output of the appliance below the cooker hood exceeds the maximum outputs quoted, please refer to the cooker manufacturer’s installation instructions.
INSTALLATION INSTRUCTIONS Draw a vertical line on the wall from the centre of the cooking appliance, using a spirit level and marking pen. This is to ensure the correct level of alignment of the appliance (5). Mark the hole position (1) on the wall 100mm either side of the vertical line ensuring that they are level and that the distance between the lowest point of the hood and the cooking appliance beneath meet the clearance requirements quoted in the paragraph titled ‘Clearance Heights’ (* - Page 12).
INSTALLATION INSTRUCTIONS Adjusting Position (10) There are 2 adjustable hooks at the rear of the hood, which can be used to adjust its position as follows: Turn screws L until the position of screws N coincides with the lower access holes. Turn the screws N to adjust the vertical and horizontal position of the hood. Lock the screws L to fasten the hood against the wall.
INSTALLATION INSTRUCTIONS Regardless of which type of installation, any wooden shelves in the area where the hood is to be fitted must first be removed, drilled and later replaced. 13 Drilling the shelves b) Using the template provided, and taking hole B as a point of reference, drill the shelves along the central axis to allow the passage of the chimney. The chimney must be inserted into the shelves before it is fixed to the hood canopy (Fig. 13).
INSTALLATION INSTRUCTIONS Air outlet directed upwards (Fig. 2a-b): - Remove the plastic plug from the upper part of the venting grill and replace it on the rear part (Fig. 16). 16 Air outlet directed towards the wall (Fig. 3): - Remove the plastic frame from the air outlet (Fig. 17). - Remove the plug from the upper part of the ducting fan unit (Fig. 18), as it is not possible to insert the flange F with the plug in place. - Fit the flange F Ø 120 or 150 mm (Fig. 19), replace the plug.
INSTALLATION INSTRUCTIONS Fixing the chimney a) b) c) d) e) 21 I Loosen the screws M fixing the two parts of the chimney and pull the inner section I (Fig. 21) almost all the way out. Remove the protective film P. Rest the lower section of the chimney in its housing on the top of the hood canopy. Lower the ducting fan unit until it reaches the wall bracket S and fix it using the screw H provided (Fig. 22). Fit cover D provided on the wall bracket S (Fig. 23).
INSTALLATION INSTRUCTIONS Electrical connection and working test: 1. Remove the metal cover by unscrewing the four self tapping screws. 2. Connect the ‘Push-Fit’ connectors coming from the fan assembly to the canopy. 3. Position the terminals as illustrated under the cover and replace the cover with the four self tapping screws. 4. Once the electrical connection has been completed, check that the worktop lighting, fan motor and the speed selection is working properly. 5.
Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts please contact your local Service Force Centre by telephoning: 08705 929929 Your telephone call will be automatically routed to the Service Force centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.
© Electrolux plc 2002 4329161_12 - 041207
