EN User manual Washing Machine ZWI 71201 WA
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3 Product description _ _ _ _ _ _ _ _ _ _ _ _ _ 4 Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 Washing programmes _ _ _ _ _ _ _ _ _ _ _ _ 8 Consumption values _ _ _ _ _ _ _ _ _ _ _ _ 11 Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ 12 First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 13 Personalisation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 13 Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Care and cleanin
• Do not change the specification of this appliance. • Obey the maximum load volume of 8 kg (refer to the “Programme chart” chapter). • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. • The operating water pressure (minimum and maximum) must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa) • The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
Water connection • Make sure not to cause damage to the water hoses. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. • Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. • The first time you use the appliance, make sure that there is no leakage. Use Warning! Risk of injury, electrical shock, fire, burns or damage to the appliance.
To activate this device, rotate the button (without pressing it) inside the door clockwise until the groove is horizontal. If necessary use a coin. To disable this device and restore the possibility of closing the door, rotate the button anti-clockwise until the groove is vertical. Detergent dispenser drawer Compartment for detergent used for prewash and soak phase or for stain remover used during the stain action phase (if available).
1 2 3 4 5 6 7 8 10 9 1 Programme selector dial 2 SPIN reduction button 6 EXTRA RINSE button 7 START/PAUSE button 3 OPTIONS button 4 PREWASH button 8 DELAY START button 9 DOOR LOCKED pilot light 5 EASY IRON button 10 Display Table of symbols Spin Programme selector dial Cotton Push buttons Spin Synthetics Rinse Hold Delicates Options Handwash Eco (Economy) Cold wash Super Quick Wool Prewash Jeans Easy Iron Curtains Extra Rinse Soak Start/Pause Miniprogramme Delay start Rinses Child
Door locked Programme selector dial, spin speed button and available options Programme Selector Dial It allows you to switch the appliance on/off and/ or to select a programme. Spin Reduction By pressing this button you can change the spin speed of the selected programme. Available options: Rinse hold By selecting this function the water of the last rinse is not emptied out to prevent the fabrics from creasing. Before opening the door it will be necessary to empty out the water.
10.1: Child safety lock This device permits you to leave the appliance unattended during it's functioning. 10.2: • Duration of the selected programme After selecting a programme, the duration is displayed in hours and minutes (for example ). The duration is calculated automatically on the basis of the maximum recommended load for each type of fabric. After the programme has started, the time remaining is updated every minute.
Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum Fabrics Load Type of Laundry DELICATES 40° - 30° Main wash - Rinses Maximum spin speed 700 rpm Max. load kg 3 - Reduced load kg 1.5 Delicate fabrics: acrylics, viscose, polyester. HANDWASH 40° - Cold Main wash - Rinses Maximum spin speed at 900 rpm Max. load 2 kg Special programme for delicate fabrics with «hand washing» care symbol. WOOL 40° Main wash - Rinses Maximum spin speed at 900 rpm Max.
Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum Fabrics Load Type of Laundry Options Detergent Compartment SOAK 30° Prewash - Soak for about 40 minutes - Stop with water in the tub Max. load 7 kg Special programme for heavily soiled laundry. The machine performs a soak at 30°C. At the end of this time the machine will stop automatically with water left in the tub.
Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum Fabrics Load Type of Laundry Detergent Compartment Options SPIN Drain and long spin Spin at the maximum speed Max. load 7 kg Separate spin for hand washed cotton garments and after programmes with the Rinse Hold option selected. You can choose the spin speed by pressing the relevant button to adapt it to the fabrics to be spun.
Programmes Standard 40 °C cotton Load (kg) Energy consumption (kWh) Water consumption (litre) Approximate programme duration (minutes) Remaining moisture (%)1) 3.5 0.61 47 140 53 1) At the end of spin phase. Off Mode (W) Left On Mode (W) 0.10 0.98 The information given in the charts above are in compliance with the EU Commission regulation 1015/2010 implementing directive 2009/125/EC.
quantities to avoid waste and protect the environment. Although biodegradable, detergents contain substances which, in large quantities, can upset the delicate balance of nature. The choice of detergent will depend on the type of fabric (delicates, woollens, cottons, etc.), the colour, washing temperature and degree of soiling.
There are two different ways to set this option: 1. Before pressing button 7: it will be impossible to start the machine. 2. After pressing button 7: it will be impossible to change any other programme or option. To enable or disable this option press simultaneously for about 6 seconds buttons 2 and 3 appears or disuntil on the display, the icon appears. Daily use Load the laundry Open the door by carefully pulling the door handle outwards.
Press this button repeatedly to change the spin speed, if you want your laundry to be spun at a different speed. The relevant pilot light illuminates. Select the available options by means of buttons 3, 4, 5 and 6 Depending on the programme, different options can be combined. These must be selected after choosing the desired programme and before starting the programme. When these buttons are pressed, the corresponding pilot lights illuminate. When they are pressed again, the pilot lights go out.
Cancelling a programme Turn the selector dial to to cancel a programme which is running. Now you can select a new programme. Opening the door after the programme has started First set the machine to pause by pressing the button 7. If the pilot light 9 blinks and after a few minutes goes off, the door can be opened. If the pilot light 9 remains lit, this means that the machine is already heating or that the water level is too high.
Remove the drawer by pressing the catch downwards and by pulling it out. Flush it out under a tap, to remove any traces of accumulated powder. To aid cleaning, the top part of the additive compartment should be removed. Place a container close to the pump (A) to collect any spillage. Pull out the emergency emptying hose (B), place it in the container and remove its cap.
Put the cap back on the emergency emptying hose and place the latter back in its seat. Replace the filter into the pump by inserting it correctly into the special guides. Screw the pump cover firmly by turning it clockwise. Caution! When the appliance is in use and depending on the programme selected there can be hot water in the pump. Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle, and is empty.
• if necessary, wait until the water has cooled down; • open the pump door; • place a bowl on the floor and place the end of the emergency emptying hose into the bowl. Remove its cap. The water should drain by gravity into the bowl. When the bowl is full, put the cap back on the hose. Empty the bowl.
Problem Possible cause/Solution The machine does not fill: The water tap is closed. • Open the water tap. The inlet hose is squashed or kinked. • Check the inlet hose connection. The filter in the inlet hose or the inlet valve filter are blocked. • Clean the water inlet filters. (See "Cleaning the water inlet filters" for more details). The door is not properly closed. • Close the door firmly. The machine does not empty and/or does not spin: The drain hose is squashed or kinked.
Problem Possible cause/Solution The machine vibrates is noisy: The transit bolts and packing have not been removed. • Check the correct installation of the appliance. The support feet have not been adjusted • Check the correct levelling of the appliance. The laundry is not evenly distributed in the drum. • Redistribute the laundry. Maybe there is very little laundry in the drum. • Load more laundry.
Spin Speed Maximum 1200 rpm Installation Unpacking All transit bolts and packing must be removed before using the appliance. You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again. Open the porthole, remove the polystyrene block fitted on the door seal and pull out all items from the drum. After removing all the packaging, carefully lay machine on it's back to remove the polystyrene base from the bottom.
Rubber feet kit (4055126249) Available from your authorized dealer. The rubber feet are particularly recommended on floating, slippery and wooden floors. Mount the rubber feet to prevent vibration, noises and displacement of the appliance during operation. Read carefully the instructions supplied with the kit. Water inlet Caution! • This appliance must be connected to a cold water supply.
In a sink drain pipe branch. This branch must be above the trap so that the bend is at least 60 cm above the ground. Directly into a drain pipe at a height of not less than 60 cm and not more than 90 cm. The end of the drain hose must always be ventilated, i.e. the inside diameter of the drain pipe must be larger than the outside diameter of the drain hose. The drain hose must not be kinked.
When installing the appliance into the kitchen furniture ensure, if possible, the hoses are placed in either of the two recesses on the back of the appliance. This will help to prevent the hoses from becoming kinked or trapped. 35 Ø 12,5-14 depth 16-22 B C 416 6 22±1,5 1 7 5 4 3 B 2 8 Caution! Do not remove the screw 8 ! Preparation and assembly of the door The machine is originally prearranged for the assembly of a door opening from right to left.
6 4 6 4 5 8 1 7 3 D Caution! Do not remove the screw 8 ! d) Counter-magnet (6) The appliance is prearranged for a magnetic closure of the door. To enable a correct operation of this device, it is necessary to screw the counter-magnet (6) (steel disk + rubber ring) into the inner side of the door. Its position must correspond to the magnet (4) on the appliance (see picture D).
water and time (the environment is protected too!). • The machine works more economically if it is fully loaded. • With adequate pre-treatment, stains and limited soiling can be removed; the laundry can then be washed at a lower temperature. www.zanussi.com • Measure out detergent according to the water hardness, the degree of soiling and the quantity of laundry being washed.
132928491-A-402012 www.zanussi.
