ZAPPY3 OWNER’ S MANUAL Read this manual completely before riding your Electric ZAPPY3.
TECHNICAL INFORMATION Model No. : ZAPPY3 Product size : 40 L x 27 W x 38 H inch (102 L x 68 W x 98 H cm) Type of motor : Permanent-magnet brushed DC wheel motor Motor power : 250 w Wheel motor, 36 V Battery type : sealed lead acid battery Battery : Three 12 volt, 7Ah Charger : 110V Charging time : 4-6 hours Rated speed : Up to 12.5 MPH ( 20 km/h) Single charge : Up to 15 MILES (25 km) Max capacity : 220 LBS (100 kg) Net weight : 70 LBS (31.
Do not expose the charger to water or any moisture. Check if battery is properly charged and installed. Charge battery after each use. Always ride on dry paved surfaces. Gravel, wet and uneven surfaces are a hazard. Sand and loose impediments are your enemy, avoid them. Never operate too fast for your skills or conditions. Follow all laws. LIST OF PARTS 1. 2. 3. 4. 5. 6. 7.
8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Balancing wheel Footboard Rear wheel Power connecting plug Connecting tube clamp Key ignition Front fender Front fork Drum brake Motor Front wheel Handle Bar 1. brake lever 2. power switch button 3. battery gauge thumb throttle Tool kits in the tool bag 1. 2. 3. 4. 5. 6. 7.
Fuse (inside the battery bag) Note: For professional reference only. Do not replace this fuse without professional help. ASSEMBLING THE ZAPPY3 1. Unpack the ZAPPY3 carefully so that you do not misplace any of the parts. 2. Place the ZAPPY3 on a flat, level surface. (You may place a cube (app. 6-8cm/ 2 ½ ? 3? thick) under the front part of the footboard; to hold it in a balance position.) A B 3. Remove the bolts and nuts from the connecting tube clamp (B).
5. Extend the handle bar tube to full upright position and slide it into connecting with the front fork. 6. Ensure that the handlebar is facing front, the brake on the left side and the throttle on the right; before tightening the handlebar tube collar clamp using the enclosed wrench. 7. Plug in the two power connecting plugs into the sockets. The design of each plugs and sockets are different. Connect the ones which best fit each other to finish the assembly. NOTE: Handle bar height adjustment.
Remove the screws from the battery compartment located at the front part of the footboard. Disconnect the wires. Lift the battery box. Connect the battery and charger using the charger convertible cable. Plug the charger into the wall outlet. RIDING THE ZAPPY3 Once you have completed the initial charge you are ready to ride. Remember, this is not a toy. 3 The ZAPPY can reach speeds up to 12.5 mph depending on the terrain and the weight of the rider. You must wear a helmet and protective pads.
2. Unscrew the bolts and nuts from the connecting tube clamp using the enclosed allen wrenches . 3. Lift the connecting tube (which is also attached to the handlebar tube). 4. Carefully place the handlebar tube on the footrest frame. 5. Finger screw the bolts and nuts back to the connecting tube clamp to avoid any misplacements. MAINTENANCE Battery: (for professional use only) The ZAPPY3 is powered by three 12 volt, 7Ah, rechargeable batteries secured in a battery bag.
TROUBLE SHOOTING GUIDE (for professional use only) Problem The power light by the thumb throttle does not illuminate when the ZAPPY3 is on. Cause 1. Battery is discharged. 2. Loose connection inside the ZAPPY3. 3. Fuse is blown. The power indicator by the thumb throttle illuminates but ZAPPY3 still does not work. Clicking noise coming from motor When the brake lever is squeezed the ZAPPY3 does not stop. Scooter is losing speed. 1. The throttle handle is not operating properly. 1.
