Z020 – EVDO Modem User Manual V6.1 2007.07.
Z020 – EVDO Modem(User Manual) AnyDATA CDMA Module Series Reference Design Specification Copyright © 2000~2007 AnyDATA Corp. All Rights Reserved. Any part of this document may not be distributed, communicated, reproduced or transmitted in any form or by any means, electronic or mechanical or otherwise, for any purpose, without the permission of AnyDATA Corp. This document can be subjected to revision without further notice. Contact Address AnyData.Net Inc.(Korea) DaeGo Bldg, 8 th.
Z020 – EVDO Modem(User Manual) Contents 1. Getting Started .....................................................................................................................................4 1.1 USB Modem .....................................................................................................................................5 1.2 Components ....................................................................................................................................7 1.3 LED indicator .
Z020 – EVDO Modem(User Manual) 1. Getting Started In order to use Z020 USB MODEM following must be satisfied: 1) Zapp Online Software and Z020 USB MODEM Driver has been installed on the computer. 2) The Z020 EVDO modem is active (the activation process has been successfully completed – this is indicated by POWER LED in green colour, and then by the restart of the modem). PLEASE CONNECT THE BATTERY AND EXTERNAL POWER SUPPLY TO INSURE MAXIMUM PERFORMANCE OF THE MODEM.
Z020 – EVDO Modem(User Manual) 1.
Z020 – EVDO Modem(User Manual) Battery (optional) Contact Switch External Antenna Port Battery Contact Pins When dismounting the battery, push the bottom of modem upward to slide easily out from the battery cradle.
Z020 – EVDO Modem(User Manual) 1.2 Components 5V DC Power Adaptor Standard USB Cable 1.
Z020 – EVDO Modem(User Manual) 2. Program Installation 2.1 Introduction This section describes step-by-step method to install Z020 USB MODEM and Zapp Online Express Software. Must install the software before connecting Z020 USB MODEM to PC/Notebook. 2.2 Minimum System Requirement 2.2.1 PC Hardware Recommend to use PC/Notebook at speed of 300 MHz or higher.
Z020 – EVDO Modem(User Manual) 2.3 USB Driver Installation and Uninstall (Windows XP/2000) 2.3.1 USB Driver Installation (Automatic) 1. The installation of the USB Wireless Modem Connect should run automatically upon selecting this option on the menu of the Installation CD. Click ”Install Modem Driver” on the menu.
Z020 – EVDO Modem(User Manual) 2. The computer needs to restart after the driver installation completed. To restart the computer later, select “I want to manually reboot later”.
Z020 – EVDO Modem(User Manual) 3. Connect the modem and PC’s USB port, and check if the driver is installed properly in “Device Manager”. See the followings to the location of “Device Manager” [Start ▶ Control Panel ▶ System ▶ Hardware Tab ▶ Devise Manager] As shown in below with red boxed that shows “AnyDATA CDMA USB Modem” and “AnyDATA CDMA USB Serial Device”, the driver has been successfully installed.
Z020 – EVDO Modem(User Manual) 2.3.2 USB Driver Installation (Manual) 1. Connect the modem and PC’s USB port with supplied USB cable. ※ The manual driver installation shall be required twice. 2. Installing “AnyDATA USB Modem Driver” window will appear. Select “Install from a list or specific location (Advanced )”. 3. Press button to proceed. 4. A window that displays a proper path of Driver will appear. 5. Select from the CD’s path “CD Rom Driver: \Driver\” folder for appropriate OS. 6.
Z020 – EVDO Modem(User Manual) 7. A window that searches “AnyDATA CDMA USB Modem” will appear. 8. Process of installing “AnyDATA CDMA USB Modem”.
Z020 – EVDO Modem(User Manual) 9. If the installation of “AnyDATA CDMA USB Modem” has been completed, following window will appear. 10. Next, it will install “AnyDATA CDMA USB Serial Device”. 11. Select “Install from a list or specific location (Advanced)”.
Z020 – EVDO Modem(User Manual) 12. Press button to proceed. 13. Select the proper path from the CD window will appear. 14. Select from the CD’s path “CD Rom Driver: \Driver\” folder for appropriate OS. 15. Press button to move to next step.
Z020 – EVDO Modem(User Manual) 16. Window that searches “AnyDATA CDMA USB Serial Device” will appear. 17. If the installation has done properly, this window will appear. This will complete the driver installation.
Z020 – EVDO Modem(User Manual) 18. Connect the modem and PC’s USB port, and check if the driver is installed properly in “Device Manager”. See the followings to the location of “Device Manager” [Start ▶ Control Panel ▶ System ▶ Hardware Tab ▶ Devise Manager] As shown in below with red boxed that shows “AnyDATA CDMA USB Modem” and “AnyDATA CDMA USB Serial Device”, the driver has been successfully installed.
Z020 – EVDO Modem(User Manual) 2.3.3 USB Driver Uninstall 1. Disconnect the modem from USB port before uninstalling the driver. under the driver folder in CD, this will start as shown below. 2. By clicking on 3. Select “Install” to uninstall the driver. To stop removing the driver, select “Cancel”.
Z020 – EVDO Modem(User Manual) 4. As shown below, click “Finish” then the driver will be uninstalled. 5. The computer must restart after the driver is uninstalled.
Z020 – EVDO Modem(User Manual) 2.4 USB Driver Installation and Uninstall (Windows Vista) ※ The same will apply to Windows Vista 64bit. 2.4.1 USB Driver Installation (Automatic) 1. The installation of the USB Wireless Modem Connect should run automatically upon selecting this option on the menu of the Installation CD. Click ”Install Modem Driver” on the menu.
Z020 – EVDO Modem(User Manual) 2. The computer needs to restart after the driver installation completed. To restart the computer later, select “I want to manually reboot later”.
Z020 – EVDO Modem(User Manual) 3. Connect the modem and PC’s USB port, and check if the driver is installed properly in “Device Manager”. See the followings to the location of “Device Manager” [Start ▶ Control Panel ▶ System and Maintenance ▶ Devise Manager] As shown in below with red boxed that shows “AnyDATA CDMA USB Modem” and “AnyDATA CDMA USB Serial Device”, the driver has been successfully installed.
Z020 – EVDO Modem(User Manual) 2.4.2 USB Driver Installation (Manual) 1. Connect the USB Modem to the computer. ※ The manual driver installation shall be required twice. 2. Click “Locate and install driver software (recommended)” when shown in below. ㅁ a 3. Click “Continue” when “User Account Control” is shown. 4. Click “I don’t have the disc. Show me other options.” as shown below.
Z020 – EVDO Modem(User Manual) 5 Click “Brower my computer for driver software (advanced)”. 6. Click “Browse” and click “Next” as shown below.
Z020 – EVDO Modem(User Manual) 7. “Installing driver software” will be shown as below. 8. Click “close” if driver will be installed successfully as shown below. ※ After the Windows shown above, the driver installation is required one more time.
Z020 – EVDO Modem(User Manual) 9. Click “Locate and install driver software (recommended)” when shown below. 10. Click “Continue” when “User Account Control” is shown. 11. Click “I don’t have the disc. Show me other options.
Z020 – EVDO Modem(User Manual) 12 Click “Brower my computer for driver software (advanced)”. 13. Click “Browse” and click “Next” as shown below.
Z020 – EVDO Modem(User Manual) 14. “Installing driver software” will be shown as below. 15. Click “close” when the driver will be installed successfully as shown below.
Z020 – EVDO Modem(User Manual) 16. Connect the modem and PC’s USB port, and check if the driver is installed properly in “Device Manager”. See the followings to the location of “Device Manager” [Start ▶ Control Panel ▶ System and Maintenance ▶ Devise Manager] As shown in below with red boxed that shows “AnyDATA CDMA USB Modem” and “AnyDATA CDMA USB Serial Device”, the driver has been successfully installed.
Z020 – EVDO Modem(User Manual) 2.4.3 USB Driver Uninstall 1. Disconnect the modem from USB port before uninstalling the driver. under the driver folder in CD, this will start as shown below. 2. By clicking on 3. Select “Install” to uninstall the driver. To stop removing the driver, select “Cancel”.
Z020 – EVDO Modem(User Manual) 4. As shown below, click “Finish” then the driver will be uninstalled. 5. The computer must restart after the driver is uninstalled.
Z020 – EVDO Modem(User Manual) 2.5 Installing Zapp Online Express Software 1. The installation of the USB Wireless Modem Connect should run automatically upon selecting this option on the menu of the Installation CD. Click ” Install / Instalare” on the menu. 2. Select the desire language as shown below. 3. Press button to proceed. By pressing button, the installation of Zapp Online Express Program will stop. 4. Welcoming message for using Zapp Online Express Program window will appear.
Z020 – EVDO Modem(User Manual) 5. Press button to proceed. 6. Next window is related to License Agreement. Please read carefully.
Z020 – EVDO Modem(User Manual) 7. Press “I Agree” button to advance to the next step.
Z020 – EVDO Modem(User Manual) 8. Next window displays asking proper path for installing the program. Default path is “C:\Program Files\ Zapp Online Express”. 9. Press button to install the program.
Z020 – EVDO Modem(User Manual) 10. When program has been successfully installed, following window will display. 11. Press button for ending the program installation. This is installed the Zapp Online Express Program. If modem is not connected to PC/Notebook and device driver is not installed, then the program will not launch even after completion of installation program.
Z020 – EVDO Modem(User Manual) 3. Using Zapp Online Express Program 3.1 Running the program There are 2 (two) ways to run the installed Zapp Online Express program. 1) Double-click shortcut icon on the desktop. 2) Navigate and run Zapp Online Express program by clicking, start, program and Zapp Online Express.
Z020 – EVDO Modem(User Manual) 3.2 Exiting the program From the Zapp Online Express program, by pressing button will quit the program. If DUN is running, the program will end after the completion of these commands.
Z020 – EVDO Modem(User Manual) 3.3 Screen Display of Zapp Online Express 3.3.
Z020 – EVDO Modem(User Manual) 3.3.2 Description of each icon Display Function RSSI Signal Strength Indicator No signal Rx Diversity available. EVDO mode available Battery Indicator Battery Fully charged Low Battery or Battery nil USB connected Charging USB External Power Connected to the Modem Either the cable is disconnected to the modem or improper port connection. Internet connected Internet disconnected Connect to the Internet button.
Z020 – EVDO Modem(User Manual) [Basic] Tab The basic configuration for connect to the network using EV-DO modem. All values are set automatically, however if wants to change the value then check appropriate box/boxes in the left and press button to take effect. UserName, Password, ServiceNum will be provided by the local carrier. [Advance] Tab This part is used to change the important parameter for EV-DO modem.
Z020 – EVDO Modem(User Manual) [ About ] Tab Displays the software version for Zapp Online Express.
Z020 – EVDO Modem(User Manual) 3.4 Connecting to the Internet Connection information, such as UserName, Password, and ServiceNum, are already inserted into the Zapp Online Express program. In case they are not inserted, you can manually type them: UserName and Password (not important for authentification), ServiceNum: #777. Then press button, to connect to the internet. If the modem is trying to connect or connected to the Internet, this above.
Z020 – EVDO Modem(User Manual) 3.5 Disconnecting from the Internet When user is ready to disconnect from the Internet, press button to end the connection. Please check the following if abrupt disconnection of modem occurred: 1) Did I intentionally disconnect USB modem? 2) Are cables properly connected? 3) Did I intentionally change Port number in environment settings? 4) Did I quit/exit the program? 3.6 Sending and Receiving calls This feature is not available with the Z020 modem in Zapp network.
Z020 – EVDO Modem(User Manual) 3.7 Viewing received or saved message (SMS can only be received when the modem is in 1x or Hybrid mode !) 1) By pressing “Inbox” icon, you will see a screen as below. 2) All received messages will be shown. 3) It will indicate whether the message was read or not. 4) Select the message then press button to delete this message. 5) Select the message then press button to view the whole contents in the display. Message read. Unread message. Sent message.
Z020 – EVDO Modem(User Manual) 4. Troubleshooting Q: I cannot connect to the Internet? A: Please check “environment setting” of program for correct ID, password and Service number. For proper ID, password and Service number, please contact service provider for more information. Q: The Internet connection speed is too slow. A: Please check whether the modem is set at 1X mode. If USB modem is set at 1X mode, then the Internet is not connected as EVDO mode.
Z020 – EVDO Modem(User Manual) Q: After the installation of the program, the program does not run and displays following message A: This means that USB modem and the compute are not connected properly. Please double check whether USB modem is connected properly to the computer. Q: During the running of the program, an error message appears and the program halts. A: The actual connection of USB modem and computer has been disconnected.
Z020 – EVDO Modem(User Manual) DECLARATION OF CONFORMITY We, SC TELEMOBIL SA, Romania, Baloteşti, j.
