Z030 Z030 Contents Caution for Safety…………………………………………………………………… Package Includes… ………………………………………………………………… Overview of the Z030… …………………………………………………………… Introduction…………………………………………………………………………… Installing and Configuring the ZO30… ………………………………………… 1. Notebook PC System Requirements… ………………………………………… 2. Installing the Z030 Manager onto Notebook PCs (Windows 2000 and XP) 3.
Caution for Safety Z030 Z030 DO NOT disassemble or modify the Card The risk of electric shock or fire may result. Do not use any detergent or chemicals such as alcohol, benzene or sniffer to clear your card. It may cause the failure or equipment or the risk of explosion. DO NOT use this equipment where the place prohibited using your card such as in hospital or in aircraft. RF energy may effect on the medical devices or aircraft.
Z030 Z030 Package Includes • W ireless Access Card (model No.
Z030 Z030 Overview of the Wireless Access Card External Antenna Connector 18Pin Connector Internal Antenna Ear-Microphone Connector LED Lamp UIM Card Connector (not available in Zapp network) 64Pin Connector
Z030 Z030 Introduction I nstall the Z030 Manager Software and Z030 drivers before using the PCMCIA card. Please do NOT insert the Z030 PCMCIA card into the laptop before following the installation steps provided below, in this user guide. Please check the contens of the purchased package. IMPORTANT ! 1. The Z030 Manager Software is available only in English language. 2. The options of the Z030 Manager Software which are not described in this user guide, are not available with the Z030 in the Zapp network.
Installing and Configuring Wireless Access Card Z030 Z030 1.
Z030 Z030 Installing and Configuring Wireless Access Card 2. Installing Z030 Manager onto Notebook PCs (Windows 2000 and XP) Insert the installation CD into your CD-ROM drive. The installation Wizard will launch and guide you through the installation process.
Installing and Configuring Wireless Access Card Z030 Z030 Press Next Button Welcome to the Access Manager Setup program. This program will instal Access Manager on your computer. It strongly recommended that you exit all Windows programs before running this Setup program. Click Cancel to quit Setup and then close any programs you have running Click Next to continue with the Setup program. WARNING: This program is protected by copyright law and international treaties.
Z030 Z030 Installing and Configuring Wireless Access Card If Z030 Manager is completely installed, click Close. (in case the specific window is displayed) Setup is complete and Access Manager is now installed! Click Close to end the Setup D uring the installation process, the following screen will appear stating the Z030 driver is not Windows XP certified. Click on Continue Anyway to continue with installation.
Installing and Configuring Wireless Access Card Z030 Z030 2-2 Install Microsoft Hotfixes I f the installation is ready, the window is displayed As below. and then click Next button Welcome to the Installshield Wizard for Microsoft Hotfixes The InstallShled(R) Wizard will install Microsoft Hotfixes on your computer. To continue, click Next. WARNING: This program is protected by copyright law and international treaties.
Z030 Z030 Installing and Configuring Wireless Access Card Installation is pop up, and then press Install button Ready to Install the program The wizard is ready to begin installation. If you want to review or change any of you installation settings, click Back. Click Cancel to exit the wizard. If Microsoft Hotfixes is completely installed, click Finish InstallShield Wizard completed The InstallShield Wizard has successfully installed Microsoft Hotfixes, Click Finish to exit the wizard.
Installing and Configuring Wireless Access Card Z030 Z030 A fter completion of installation, a message box is displayed, asking if you wish to reboot Windows. Press Yes button if you wish to reboot Windows imediately. You must restart your system for the configuration Changes made to Microsoft Hotfixes to take effect. Click Yes to restart now or No if you plan to restart later. 3. Wireless Access Card Insertion and Device Initialization 1.
Z030 Z030 Installing and Configuring Wireless Access Card 1-2. Ubiquam UM-300 Multifunction Parent W indows 2000, XP: Check Install the software automatically and press Next Welcome to the Found New Hardware Wizard This wizard helps you install software for. Ubiquam UM-300 Multifunction parent If your hardware come with an installation CD or floppy disk, insert it now.
Installing and Configuring Wireless Access Card Z030 Z030 1-4. Ubiquam UM-300 USB Interface (Function 0) W indows 2000, XP: Check Install the software automatically and press Next Welcome to the Found New Hardware Wizard This wizard helps you install software for. Ubiquam UM-300 Function 0 If your hardware come with an installation CD or floppy disk, insert it now.
Z030 Z030 Installing and Configuring Wireless Access Card 1-6. Ubiquam CDMA 2000 Drive W indows 2000, XP: Check Install the software automatically and press Next Welcome to the Found New Hardware Wizard This wizard helps you install software for. Ubiquam CDMA2000 If your hardware come with an installation CD or floppy disk, insert it now. What do you want the wizard to do? Install the software automatically(Recommended) Install from a list or specific location(Advanced) Click Next to continue. 2.
Z030 Z030 Using Z030 Manager 5 4 3 2 6 1 7 8 9 18 17 16 15 10 11 12 13 14 1. Connect/ Disconnect 2. Window Close 3. Window Minimize 4. Message Incoming 5. R SSI(Receiving Signal Strength Indicator) 6. Date/Time 7. Status 8. Setting 9. Message 10. Call History 11. Volume Control 12. Send 13. Clear 14. End 15. Dial Pad 16. Phonebook 17. Speed Dial 18.
Z030 Z030 Message 1. SMS You can view and organize short messages. 2. Receive SMS Arrival of new SMS is displayed on indicator. To read SMS ey click to pop up the message box. Double-click the K message you want to read from the message box to open the mail. 3. Delete 1) After selecting messages from the message box, click button to delete messages. 2) Or click “Delete” in the open message window to delete messages.
Connecting to the Internet Z030 Z030 1. Connecting to the Internet Then press connect button, it will automatically connected to the Internet. If it is connected to the Internet, then icon will appear. When user is ready to disconnect from the Internet, press button to end the connection.
Z030 Z030 Setting Click “Setting” to open the setting window to set various items for the dial pad. 1. Network Input basic information for network. For data mode, decide whether one of EV-DO and 1X, or both of them is used. E V-DO + 1X- Hybrid mode. It will access EV-DO network first. If it’s not possible, it will access 1Xnetwork. E V-DO - Accessible only to EV-DO network. 1 X - Accessible only to 1X network. D ial-up Networking description a.
Setting Z030 Z030 2. Advanced P hone lock enable - You can select whether “Phone lock” is used or not, and change “LockCode.
Z030 Z030 FAQ (Frequently Asked Questions) Below is a list of common error messages and possible solutions regard the use of your Wireless Access Card. For amore detailed listing of errors and possible solutions, please see the User’s Guide located on your installation CD. Error “Initialization Fail“ “Out of service area“ 22 22 solution If this message is displayed, please right click the Z030 Manager icon on your system tray and click “Exit”.
Technical information Standard Z030 Z030 Transmit(Tx) CDMA 1X450MHz 453~457.5MHz EV-DO 453~457.5MHz Receive(Rx) 463~467.5MHz 463~467.5MHz Maximum Data Transmission 153.6kbps 2.4576Mbps Simultaneously in forward and reverse links Operating Voltage 3.3V Note : TX,RX frequency band is basically I band. Notice: This manual is written to help users. The supplier can upgrade the software to improve the performance without a notice.
DECLARATION OF CONFORMITY We, SC TELEMOBIL SA, Romania, j. Ilfov, Bucharest Way no 2B bis, registration number at the Registry of Commerce no: 1596697, assure, guarantee and declare at ours own risk, in conformity with the 5 th article from the Government Resolution nr 1022 / 2002 regarding the guidance of products and services which could risk the life, health or the work and environment security that the following product: Z030 CDMA 450 SINGLE BAND PCMCIA MODEM CARD, UM 300 made in Korea by UBIQUAM CO.