Use and Care Manual

Aqua ZAR® Interior Water-Based Polyurethane
Aqua ZAR Interior Water-Based
Polyurethane by UGL combines the beauty
and durability of an oil-based polyurethane
with the environmental benets of a water-
based clear nish.
is fast drying, low-odor formula resists
most household chemicals and abrasions.
AQUA ZAR’s full-bodied formula brushes on
like a conventional polyurethane for
maximum durability and beauty. Child safe
when dry.
Meets all environmental standards for low
emission of solvent vapors.
Full body, high film build formula
A durable floor finish
Non-yellowing, dries crystal clear
Complies with all current VOC requirements
is non-yellowing, environmentally safe,
clear wood nish is specially formulated to
protect and beautify cabinets, furniture, wall
paneling, woodwork, and oors. Dries
crystal clear, making it an ideal nish to use
over light-colored or white stains. Exotic
Hardwoods Approved-Ideal for use on
Teak, Brazilian Walnut and other exotic
wood species.
Do not apply over wood llers or nishes
containing wax or stearates. Do not use steel
wool. Do not thin.
COMPOSITION:
Water base
SHEEN:
Gloss 90+
Semi-Gloss 70±3
Satin 45±3
Antique Flat 20±3
% WEIGHT SOLIDS:
32-34%
% VOLUME SOLIDS:
30-32%
DENSITY (LBS./US GAL.):
8.6-8.7
VISCOSITY:
55-60 KU @77ºF
pH:
8.5-9
COLORS:
N/A
DRY TIME:
• To touch: 30 minutes
• To recoat: 2 hours
• Light use: 24 hours
• Moderate use: 3-5 days
• Maximum use: 1 week
Note: Maximum cure and dry time will
be prolonged when slightly humid and
damp, cool conditions prevail.
CLEAN UP:
Warm soapy water
Dispose of contaminated absorbent,
container and unused contents in
accordance with local, state and federal
regulations.
COVERAGE (SQ. FT./US GAL.):
• 400-500 sq. ./gal.
Note: Actual coverage will vary
depending upon application method,
surface texture and porosity.
RECOMMENDED FILM THICKNESS/COAT:
N/A
FLASH POINT:
N/A
SHELF LIFE:
Unopened >5 years
FREEZE/THAW:
Keep from freezing
CONTAINER SIZES:
One pint (US), one quart (US) and one
gallon (US) cans
Does not exceed 275 g/L
N/A
Do not thin.
New Wood: Sand smooth using ne
sandpaper, vacuum sanding dust. Wipe
using a tack-cloth to remove any remnants of
dust prior to application. Do not use steel
wool. If open-grained woods are to be lled,
use a ller that does not contain stearates or
waxes such as ZAR Wood Patch or ZAR
Trowelable Wood Patch.
Old Clear Finishes in Good Condition:
Remove grease, dirt, and wax. Sand lightly in
the direction of the grain to remove any gloss.
Do not use steel wool. Vacuum all sanding
dust. Wipe using a tack-cloth to remove any
remnants of dust prior to application.
If the old nish contains wax or stearates,
regardless of condition, remove completely.
Test Aqua ZAR in an inconspicuous area for
compatibility.
Old Clear Finishes in Poor Condition,
Lacquer or Shellac:Remove completely. Do
not use steel wool. Sand and vacuum all
sanding dust. Wipe using a tack-cloth to
®®
UNITED GILSONITE LABORATORIES
MAILING: P.O. Box 70, Scranton, Pennsylvania, 18501
SHIPPING: 1396 Jefferson Avenue, Dunmore, Pennsylvania, 18509
T
OLL FREE: 1-800-UGL-LABS (845-5227)
P
HONE: 1-570-344-1202 • FAX: [phone]
www.ugl.com
Z A R ® W O O D F I N I S H I N G P R O D U C T S
O V E R
DRY TIME:
30 Minutes
Recoat 2 Hours
CLEAN-UP:
Soap and Water
COVERAGE:
2-3 Coats
3 Coats for Floors
SPREAD RATE:
400-500 Sq.
Ft../Gallon