User's Manual
zBoost z-Force® YX240 Installaon Overview
Download Product Manual at www.Wi-Ex.com
Need a Signal Boost in Your Home or Office?
See the full line of zBoost Signal Boosters at www.Wi-Ex.com
Designed for consumers, the Wi-Ex® cell phone signal booster, z-Force, extends an in-vehicle Cell Zone. The dual band unit captures the signal outside of your
car and amplifies it on the inside for a stronger “hands-free” signal. The unit incorporates a cradle and works with both 1900 MHz and 800 MHz phones – (not
Nextel/iDEN, 4G or 2100 MHz). Installaon is easy - this package includes everything you need.
Package Contents
① zBoost Amplifier Cradle and Mounng Adhesive
② Exterior Magnec Mount Antenna with 10 Cable
③ 12v DC Cigaree Power Adapter with 3 Cable - OR -
④ Gooseneck Adapter
Note: If your z-Force product includes the oponal Gooseneck Adapter (④), begin your installaon on Step 2. Otherwise, with the standard CLA (③), begin
on Step 1. To purchase the Gooseneck Adapter, visit www.Wi-Ex.com.
WARNING! Use only the provided power adapter. The use of any other power adapter or cable will harm the system and void your warranty. Before installing,
please read the enre contents.
Installaon
Step 1. Posion zBoost Amplifier Cradle -
Choose the locaon within your vehicle to
mount the zBoost Cradle. Choose a locaon with a flat surface where Velcro can be applied.
Avoid placing behind any metallic objects. Do not make contact with any metal surface.
Posion Amplifier Unit within 3 feet reach of power source. Clean the area where the
mounng adhesive will be applied. Allow to dry. Peel backing to expose the adhesive and
press onto the desired locaon. Remove the backing from the remaining side and press the
zBoost Cradle into place.
Step 2. Posion Exterior Magnec Mount Antenna -
Posion Exterior Magnec
Mount Antenna on roof of vehicle, making sure magnet is secured to metal surface. Thread
the cable from exterior to the interior of the vehicle. Connect the cable connector to the
Amplifier Cradle Unit.
NOTE: The cord running from exterior to interior of vehicle is designed to withstand
pressure when closed in door.
Step 3. Connect DC Power -
Connect DC Power Adapter to the zBoost Cradle using the
provided cable or, if you are using a Gooseneck Adapter, by snapping the back of the cradle
onto the Gooseneck. Then connect to power source within vehicle.
NOTE: The le side of the z-Force Cradle features a USB power connecon so that you can
charge your cell phone while using this product.
Step 4. Examine Amplifier LED -
The lighted area on the zBoost Amplifier Cradle indicates the condion of the system. Review LED Indicator secon below.
NOTE: This product uses an auto-shut-off feature. When no movement is detected for 10 minutes, the unit will power down automacally to avoid draining
your vehicle’s baery and will display a slow blinking green LED.
Step 5. Quick System Check
- Place your cell phone in the zBoost
Cradle. Check signal strength bars. Next, turn the system off (unplug unit). You should
noce a decrease in signal bar strength. The excepon is if you are in an area where, with the system off, your phone is at full signal strength. Please note
when you turn the system on, if your phone is receiving maximum signal strength you will not see a difference. In order for this quick test to work, you will
need to test unit in a less than maximum signal strength area.
© 2011 Wi-Ex, Inc. Wi-Ex.com | One Meca Way, Norcross, GA 30093 | 1-800-871-1612 DMAN-0046 Rev A
FCC ID: SO4YX240-PCS-CEL
IC: 5544A-YX240PCSCEL
LED Status Condion
Solid Green Normal operaon
Slow Blinking System has powered down aer sensing no
Green movement for 10 minutes. Once movement
resumes, system will power up.
Blinking Red System is experiencing Interference. This is
caused by inadequate distance between the
Cradle and Exterior Antenna. Resolve by
moving Exterior Antenna further back on the
vehicle.
Solid Red Indicates issue with power adapter.
One possible cause is a loose power
connecon. Verify that the adapter is properly
secured in the socket.
Another possible cause is the use of an
incompable power adapter. Use only the
provided adapter and/or cable or risk harm to
your zForce system.
If you are using the adapter provided with
your zForce system, please contact customer
service for a replacement.
LED INDICATORS
PCS band Cellular band
Uplink: 1850-1910 MHz
Downlink: 1930-1990 MHz
Uplink: 824-849 MHz
Downlink: 869-894 MHz
Band supported
up to 35dB up to 43dB
A, D, B, E, F, C
A, B, A’, B’
CDMA, GSM, GPRS, EDGE, EVDO, 1xRTT, UMTS, HSPA, 3G
Output Power
Networks
Power Source
FCC Parts 15 & 24 (PCS), Parts 15 & 22 (CEL), Industry Canada
Base Unit Size and Weight
Operang Condions
Frequency
System Gain
System Cerficaons
4.4” x 3.0” x 1.9” – 20 oz.
5 - 50°C (40 - 122° F)
This product uses patented technology to protect the carrier network (US 7,706,744);
addional patents pending
12V adapter
DL: +0dBm UL: +21dBm
zBOOST ZFORCE YX240 TECHNICAL SPECIFICATIONS
OR
OR
OR
OR
④ ③②①
④④
③
③
②
①
③
③
③
④
④
④
Gooseneck
(optional)
①
Power Adapter
(CLA)
zForce Cradle
Amplifier
Exterior Magnetic
Mount Antenna
USB Power
Connecon
12 v Adapter
LED Indicator
Gooseneck Adapter
Exterior Antenna
zBoost Amplifier Cradle
④
③
②
①