Quick Setup Guide

ManualsBrandsZCOM ManualsComputers & Accessories5GHz 11ac Wireless Bridge

This Quick Setup Guide provides step-by-

step instructions on how to set up your

Access Point. After completing the steps

described in this Guide, you will be able to

place the AP at your site and provide

wireless network access to users.

PACKAGE CONTENTS

Z-COM, Inc.

SP220-C03

5GHz 11ac Wireless Bridge

Quick Setup Guide

• A computer running Windows 7, Vista, or XP

• A CAT5 UTP cable of required length

• Power adapter/PoE injector came with the

package. (4-Pair 802.3at PoE injector 60W)

STEP 1: POWER ON THE AP

The Access Point comes with a PoE injector kit

for connecting to power over the Ethernet port.

The Access Point automatically turns on as soon

as it is connected to a power source.

SETUP REQUIREMENTS

Before installing your Access Point, be sure that

you have the following:

• Wireless Access Point (1)

• Mounting screws and bracket (1)

HARDWARE OVERVIEW

Front View

LED Indicators on the Device

LED State Description

1 PWR

Off No power to AP

Green

AP power on, device

ready

2 WLAN

Off 5G radio disabled

Blinking

Green

5G radio enabled or

data being

forwarded

3 LAN

Off

Ethernet port not

connected

Green

Ethernet port

connected

Blinking

Green

Ethernet link activity

No. Item

1 Ground

2 LED

PoE/LAN Port

4 Reset Button

5 LAN Port (Option)

Rear View

Bottom View

Summary of content (8 pages)

PAGE 1
Z-COM, Inc. SP220-C03 Rear View 5GHz 11ac Wireless Bridge Quick Setup Guide This Quick Setup Guide provides step-bystep instructions on how to set up your Access Point. After completing the steps described in this Guide, you will be able to place the AP at your site and provide wireless network access to users.
PAGE 2
Cautions: 1. Use only the power adapter and PoE injector that came with the wireless AP. 2. Make sure that the PoE injector is properly grounded 1. Insert one end of an Ethernet cable to the P+D/OUT port on the PoE injector. 2. Insert the other end to the LAN/PoE port on the Access Point. 3. Connect a power cord to the PoE injector. 4. Connect the power plug to a wall socket. STEP 2: CONNECT THE AP TO YOUR PC 1. Insert one end of an Ethernet cable to the DATA/IN port on the PoE injector as figured above.
PAGE 3
4. Configure the common RF setting as such Country/Region domain and Channel. 5. Click Apply to save the changes. Configuring for Standalone Operation Before configuring fat AP Basic settings, make sure that AP mode is set to Fat AP. 1. If currently in Thin AP Mode: On the main menu on the left, click Advanced Setting. Select Fat AP from the drop-down list. Click Apply to take effect. 2. On the main menu on the left, click Basic Setup. In the Basic Setup page, go to the section Configure AP as.
PAGE 4
STEP 5: INSTALL THE AP 1. Disconnect the AP’s power adapter from the power outlet (or disconnect the PoE cable). 2. Move the AP to its permanent location (accessible to both power source and network connections). 10. In Network Authentication, select the desire authentication method and then enter the encryption phrase accordingly. 11. Click Apply to save the changes. 12. Click Logout to exit the Web interface. STEP 4: VERIFY THE CONNECTION 1. Connect the AP to your network. 2.
PAGE 5
3. Slide the gasket and rubber stopper into the locking nut. 4. Connect the RJ-45 connector into the LAN port of the Access Point. 5. Flush the gasket, rubber stopper and locking nut together into the LAN port opening, then twist the locking nut to seal the opening. 6. Slide the sealing cap over the bare end of the Ethernet cable. 7. Tighten the sealing cap. 2. Insert the other end of an Ethernet cable to the P+D/OUT port on the PoE injector.
PAGE 6
2. Attach the pole lock frame and screw two bolts back. Tighten them approximately. External 5GHz directional-antennas (Optional accessory_ANT-D5G-23) 3. Attach two 1.5M N-type cables to the reserved antenna jacks, and connect to the directional antenna. 1. Align the antenna mount with antenna; screw tightly all four screws. Note: Dual linear, ±45°, HPBW/Horizontal 10°, HBPW/Vertical 10°, IP57 Waterproof Note: Before screw the directional-antenna, please reserve 15 cm between the device and antenna.
PAGE 7
Safety Notice 1. Do not install the device close to any electrical grounding device or lightning protection system. Place the device’s own grounding and lightning protection system apart from any electrical grounding device and lightning protection system as far as possible. 2. Protect components from electrostatic discharge: Please wear an ESD wrist strap or handle the power adapter by its edge and do not touch any component or printed circuit boards, especially for module device. 3.
PAGE 8
Declaration of Conformity Hereby, Z-COM, Inc. declares that the radio equipment type SP220-C03 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.zcom.com.tw/servicepage Federal Communications Commission FCC Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.