D ra ft 1 CR8178-SC Standard Cradle Quick Reference Guide
CR8178-SC Standard Cradle Introduction The CR8178-SC (standard) cordless digital scanner cradle acts as charger and radio communication interface for the DS8178 cordless digital scanner. The CR8178-SC can sit on a desktop or be mounted on a wall. The CR8178-SC healthcare cradle can sit on a desktop or be mounted on a wall or cart. The cradle receives data from the digital scanner via a Bluetooth radio, and sends that data to the host through an attached cable.
Quick Reference Guide 3 Cradle Features Top Removable Scanner Latch (vertical/mobile cart mount position) LED Pairing Bar Code 1 Page Button ra ft Scanner Lock (when converter knob is set to vertical mount) Charging/ Communications Contacts D LED Removable Scanner Latch (horizontal mount position)
CR8178-SC Standard Cradle Bottom Interface Cable Groove Rubber Foot Rubber Foot Keyhole Mounting Hole Interface Port Vertical Mount Threaded Brass Screw Holes (2 M4x5 mm) Interface Cable Groove 1 Interface Cable Support Hook Rubber Foot ra ft Keyhole Mounting Hole Rubber Foot D Desk Point Triangle Indicator Appropriately to Select Wall or Mobile Cart Desk/Wall Mount Converter Knob NOTE When mounting on a mobile cart the desk/wall mount converter knob must be in the wall mount position (l
Quick Reference Guide 5 Cradle Connections 1. Connect the appropriate cable to the power supply and an AC power source, if 2. 3. 4. 5. 6. necessary. This ensures detection of the host and prevent inadvertently back powering the cradle from improper detection of the host. Insert the interface cable into the host port. Insert the interface cable into the cradle’s host port. If applicable, thread the interface cable under the interface cable support hook and run the cable along the interface cable groove.
CR8178-SC Standard Cradle Mounting the Cradle Horizontal Mount 1. Ensure the scanner latch is in the horizontal mount position (see Removable Scanner Latch (horizontal mount position) on page 3). 2. Use a screwdriver or coin to turn the desk/wall mount converter knob (triangle indicator) to the position shown below. Desk Position 3. The rubber feet on the bottom of the cradle provide traction and prevent Vertical Mount/Mobile Cart 1 surface damage.
Quick Reference Guide 7 3. Use a screwdriver or coin to turn the desk/wall mount converter knob (triangle indicator) to the position shown below. The scanner locking mechanism in the cradle protracts to engage and grip the depression at the base of the digital scanners handle. Wall or Mobile Cart Position 4. Attach the interface and power cables (see Cradle Connections on page 5). 5. Press the cables into the cable grooves. 6.
CR8178-SC Standard Cradle Inserting the Digital Scanner in the Cradle To insert the digital scanner in the cradle: 1. Insert the scanner into the cradle top first ensuring that the cradle latch depression connects with the scanner latch on the cradle. 2. Push the handle until it clicks into place, engaging the contacts in the cradle and digital scanner.
Quick Reference Guide 9 Lost Connection to Host If scanned data does not transmit to the cradle’s host, ensure that all cables are firmly inserted and the power supply is connected to an appropriate AC outlet, if applicable. If scanned data still does not transmit to the host, reestablish a connection with the host: 1. Disconnect the host interface cable from the cradle. 2. Wait three seconds. 3. Reconnect the host interface cable to the cradle. 4.
CR8178-SC Standard Cradle LED Indication Maintenance Indications Red (stays on) Enter boot loader Red blinking Firmware installation Troubleshooting ra ft 1 If the cradle does not work after following the previous procedures: • Check the system power. • Check for loose cable connections. • Check that the digital scanner is inserted properly in the cradle. • Check that the host settings are correct and the cradle is connected to the appropriate port on the host.
Quick Reference Guide 11 Regulatory Information This device is approved under Zebra Technologies Corporation. This guide applies to the following Model Number: CR8178-SC. All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold and will be labeled as required. Local language translations are available at the following website: http://www.zebra.com/doc.
CR8178-SC Standard Cradle Warnings for Use of Wireless Devices Caution: Please observe all warning notices with regard to the usage of wireless devices. Potentially Hazardous Atmospheres - Fixed Installations You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles such as grain, dust, or metal powders.
Quick Reference Guide 13 RF Exposure Guidelines Safety Information • Reducing RF Exposure - Use Properly • Only operate the device in accordance with the instructions supplied. International The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. For information on 'International' human exposure to electromagnetic fields, refer to the Zebra Declaration of Conformity (DoC) at http://www.zebra.com/doc.
• • • • CR8178-SC Standard Cradle Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment in an outlet on a circuit different from the receiver is connection. Consult the dealer or an experienced radio/TV technician for help. Radio Transmitters (Part 15) This device complies with Part 15 of the FCC Rules.
Quick Reference Guide 15 Japan (VCCI) - Voluntary Control Council for Interference Class B ITE Korea Warning Statement for Class B ITE Brazil (UNWANTED EMISSIONS - ALL PRODUCTS) D ra ft 1 Declarações Regulamentares para CR8178 - Brazil Nota: A marca de certificação se aplica ao Transceptor, modelo CR8178.
CR8178-SC Standard Cradle potencia radiada máxima no supera 7,5mW/MHz en cualquier banda de 1MHz y 0.1875mW/25kHz en cualquier banda de 25kHz. China 忂彯孧斖ẍᶳ仹⛨⎗ᶳ弥⛘宕妨㓗㊩䘬ṏ⑩宜㖶Ḏ www.zebra.com/support Eurasian Customs Union Евразийский Таможенный Союз 1 Данный продукт соответствует требованиям знака EAC. Mexico South Korea ra ft Restrict Frequency Range to: 2.450 - 2.4835 GHz.
Quick Reference Guide 17 Waste Electrical and Electronic Equipment (WEEE) D ra ft 1 English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product, please go to: http://www.zebra.com/weee. Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent être retournés à Zebra pour recyclage. Pour de plus amples informations sur le retour de produits, consultez : http://www.zebra.com/weee.
CR8178-SC Standard Cradle D ra ft 1 Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a http://www.zebra.com/weee weboldalra. Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Zebra för återvinning. Information om hur du returnerar produkten finns på http://www.zebra.com/weee.
Quick Reference Guide 19 CMM Disclosure 10 ᴿᇩ⢟䍞 (Metal Parts) (Circuit Modules) (Cables and Cable Assemblies) (Plastic and Polymeric Parts) (Optics and Optical Components) (Batteries) (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) O O O O O O X O O O O O O O O O O O O O O O O O O O O O O O O O O O O O 1 (Parts) O: X: ra ft 本表格依据SJ / T 11364 的规定编制。 表示该有害物质在该部件所有均质材料中的含量均在 GB/ T 26572 规定的限量要求以 下。 表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/ T 26572 规定的限量要 求。( 企业可在此处,根据实际情况对上表中打 “
1 ra ft D Zebra Technologies Corporation 3 Overlook Point Lincolnshire, Illinois 60069 USA http://www.zebra.com Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. © 2016 Symbol Technologies LLC, a subsidiary of Zebra Technologies Corporation. MN-002784-02 Rev.