ET1 ENTERPRISE TABLET QUICK START GUIDE PRELIMINARY
Motorola Solutions reserves the right to make changes to any product to improve reliability, function, or design. Motorola Solutions does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
Features Decode LED Microphone Light Sensor Battery Charge LED Communication LED Front-facing Camera Touch Screen PRELIMINARY Programmable Buttons Back Button Home Button Menu Button 3
Features Secondary Microphone Camera Flash Rear-facing Camera USB Host Expansion Right Scan/Action Button Power Button Left Scan/Action Button Battery Charging LED Battery Release Latch PRELIMINARY Battery Speaker Speaker Headset Jack 4 I/O Connector HDMI Output Connector
Introduction Install the SIM Card This guide covers the following configurations: The ET1N2 requires an activated SIM card. Obtain the card from a service provider. • ET1N0 (WLAN only) • ET1N2 (WLAN and WAN) • ET1N0 and ET1N2 with scan modules. Getting Started 1. Lift access door. 2. Insert SIM card into SIM holder with contacts facing down and cut edge facing away from the holder. 3. Close access door.
Install the Battery Charge the Battery 4. Remove the battery from the packaging. Before using the ET1, charge the battery using one of the following accessories: 5. Align the tracks on the sides of the battery with the rails of the battery compartment. • Single-slot USB Docking cradle • Four-slot Charge Only Docking cradle • USB/Charge cable and power supply. NOTE Rails The battery can be charged separately using the Four-slot Battery Charger. 1.
WAN Activation In order to use the WAN radio for data communication, the ET1N2 must be activated on the service provider’s network. By default, the ET1N2 is configured for a GSM network. To activate on a CDMA network, manually configuration is required. For WAN data configuration, refer to the ET1 Integrator Guide. a. Press and hold the Power button until the Device options menu appears. b. Touch Reset. c. After resetting the Activate your phone screen appears.
Launch Applications Configure the ET1 To launch an application: To configure ET1 settings, touch > Settings. Refer to the ET1 Enterprise Tablet User Guide and Integrator Guide for information on configuring the ET1. 1. Touch the Launcher icon. The Launcher screen displays. Power Button Launcher Use the Power button to place the ET1 in suspend mode, battery swap mode, to reset the ET1 or to power off the ET1. Suspend Mode 2. Touch an application icon to launch the application.
Reset Reset the ET1 if applications stop responding. Press and hold the Power button until the Device options dialog box appears then touch Reset. Power Off To power off the ET1, press and hold the Power button until the Device options dialog box appears, then touch Power off. When the Power off dialog box appears, touch OK. Refer to the ET1 Enterprise Tablet User Guide for setup instruction for locking the screen.
Photos and Videos 1. Touch Launcher > Camera and then touch the video Use the rear-facing camera to take photos and capture video. NOTE A microSD card is required to save photos and videos. icon . 2. Point the ET1 at the subject. 3. On the screen, frame the subject in the window. 4. Touch the on-screen record button 5. Touch the on-screen stop button to begin recording. to end recording. View photos and videos using the Gallery application. To take a photo: 1. Touch Launcher > Camera. 2.
Connect to a WLAN Network Connect to a Mobile Data Network To set up a WLAN network: To connect the ET1N2 to a mobile data network: 1. Touch 1. Touch > Settings > Wireless & networks. 2. Touch the Wi-Fi checkbox to turn on Wi-Fi. A green check appears in the checkbox and the Wi-Fi icon appears in the Status Bar indicating that Wi-Fi is enabled. 3. Touch Wi-Fi settings. The ET1 searches for WLANs in the area and lists them under Wi-Fi networks. 4. Select the desired network. 5.
Battery Replacement To replace the battery: 1. Press and hold the Power button until the Device options menu displays. 2. Touch Battery Swap. The Scan LED lights red. 3. Wait until the Scan LED turns off. 4. Turn the ET1 over. 5. Press thumb against the side of the ET1 and battery. Using the index and middle fingers, move the battery release latch toward thumb and pull the battery out of the battery compartment. PRELIMINARY 6.
Accessories The following accessories are available for the ET1: • Single-slot Docking Cradle • Four-slot Charge Only Docking Cradle • Four-slot Battery Charger • Handstrap Holster Protective Rubber Bezel USB/Charge Cable Two-way DC Cable PRELIMINARY Power supplies.
PRELIMINARY Motorola Solutions, Inc. 1301 E. Algonquin Rd. Schaumburg, IL 60196-1078, U.S.A. http://www.motorolasolutions.com MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2012 Motorola Solutions, Inc. All Rights Reserved.