User's Manual

Introduction The MOD-8132-6001S sensor module is a USB sensor extension to the AP-8132 model access point for use with the Motorola Solutions ADSP platform. It provides wireless security sensing mechanisms, allowing monitoring and reporting within the AP-8132's radio coverage area. The output of the sensor's detection mechanisms are reported within the ADSP system. Document Conventions The following graphical alerts are used in this document to indicate notable situations:
NOTE Tips, hints, or special requirements that you should take note of.
CAUTION Care is required. Disregarding a caution can result in data
loss or equipment malfunction.
WARNING! Indicates a condition or procedure that could result in
personal injury or equipment damage.
Warnings • Read all installation instructions and site survey reports, and verify correct equipment
installation before connecting the MOD-8132-6001S sensor module.
•Remove jewelry and watches before installing this equipment. •Verify any device connected to this unit is properly wired and grounded. •Verify there is adequate ventilation around the device, and that ambient temperatures meet
equipment operation specifications.
Precautions Before installing an MOD-8132-6001S sensor module, verify the following: •You are using one of the correctly rated power solutions for the AP-8132 access point:
- AP-PSBIAS-2P3-ATR power injector - PWRS-14000-247R external power supply
•Motorola Solutions recommends you do not to install the MOD-8132-6001S in wet or dusty
areas.
•Verify the environment has a continuous temperature range between 0° C to 50° C.
Specifications
Length 2.5 in /6.3 cm Width 6.0 in / 15.24 cm Height 1.625 in / 4.127 cm Weight 0.270 lb / 0.123 kg Operating Temperature 0
° to 50° celsius / 35° to 122° farenheit
Storage Temperature -20
° to 80° celsius / -4° to 176° farenheit
Radio Technology 2x2 MIMO 802.11 a/b/g/n The MOD-8132-6001S sesnsor module is plenum rated.
MOTOROLA SOLUTIONS INC. 1303 E. ALGONQUIN ROAD SCHAUMBURG, IL 60196 http://www.motorolasolutions.com
MOD-8132-6001S Internal Antenna Sensor Module
Installation Guide
72-167783-01 Revision B January 2013
(2)
(1)
(3) (4) (5) (6)
Installing the MOD-8132-6001S Internal Antenna Sensor Module
1. Align the tabs on the sensor module with the corresponding slots on the
Access Point.
2. Securely attach the sensor module to the Access Point. 3. Confirm the sensor module is operational by observing its LEDs.
Regulatory Information This device is approved under Motorola Solutions, Inc. This guide applies to Model Number KHUSB600. All Motorola devices are designed to be compliant with rules and regulations in locations where they are sold and will be labeled as required. Local language translations are available at the following website: http://supportcentral.motorola.com.
Any changes or modifications to Motorola Solutions equipment, not expressly approved by Motorola Solutions, could void the user's authority to operate the equipment. When Motorola Solutions devices are professionally installed, the Radio Frequency Output Power will not exceed the maximum allowable limit for the country of operation. This device is only to be used with a Motorola Solutions AP-8132 Access Point.
Wireless Device Country Approvals Regulatory markings, subject to certification, are applied to the device signifying the radio(s) is/are approved for use in the following countries: United States, Canada, Japan, China, S. Korea, Australia, and Europe (Note 1,2). Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at http://www.motorola.com/doc.
Note 1: For 2.4GHz or 5GHz Products: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Note 2: Operation of the device without regulatory approval is illegal.
Country Selection Select only the country in which you are using the device. Any other selection will make the operation of this device illegal. Frequency of Operation - FCC and IC 5 GHz Only The use in the UNII (Unlicensed National Information Infrastructure) band 1 (5150-5250 MHz) is restricted to Indoor Use Only; any other use will make the operation of this device illegal. Industry Canada Statement: Caution: The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-Channel mobile satellite systems. High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices. Avertissement: Le dispositive fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bands 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
Health and Safety Recommendations Warnings for Use of Wireless Devices Please observe all warning notices with regard to the usage of wireless devices. Potentially Hazardous Atmospheres - Fixed Installations You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles (such as grain, dust, or metal powders). Safety in Hospitals Wireless devices transmit radio frequency energy and may affect medical electrical equipment. When installed adjacent to other equipment, it is advised to verify that the adjacent equipment is not adversely affected. Pacemakers Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with independent research and recommendations by Wireless Technology Research. Persons with Pacemakers:
• Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker
when turned ON.
• Should not carry the device in a breast pocket.
• Should use the ear furthest from the pacemaker to minimize the potential for
interference.
• If you have any reason to suspect that interference is taking place, turn OFF your
device.
Other Medical Devices Please consult your physician or the manufacturer of the medical device, to determine if the operation of your wireless product may interfere with the medical device.
RF Exposure Guidelines Safety Information Reducing RF Exposure - Use Properly Only operate the device in accordance with the instructions supplied. International The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. For information on "International" human exposure to electromagnetic fields refer to the Motorola/Symbol Declaration of Conformity (DoC) at http://www.motorola.com/doc. US and Canada Co-located statement To comply with FCC RF exposure compliance requirement, the antenna used for this transmitter must not be co-located or operating in conjunction with any other transmitter/antenna except those already approved in this filling. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth foa na uncontrolled environment. This equipment should be installed and operated with minimum distance 30cm between the radiator and your body. NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles) Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 30 cm de distance entre la source de rayonnement et votre corps.