User's Manual

ManualsBrandsZebra Technologies ManualsElectronicsZebra Embedded RFID Radio-Media Auth

12 Zebra ZXP Series 8 Card Printer User’s Manual P1011091-001 Rev. A

Installation and Setup

Installing the Card Cleaning Roller

The Card Cleaning Roller cleans the cards entering the Printer from either the Input Hopper or

the Single-Feed Input.

Step 1. Remove the Card Cleaning Roller from its packaging. To avoid contamination,

always hold the roller by the ends.

Step 2. Peel the protective wrapper from the Card Cleaning Roller.

Step 3. Open the Printer Door by pressing the Door Release button on the top of the Printer.

Step 4. Locate the area where the Card Cleaning Roller will be installed; circled below.

Step 5. Hold the Card Cleaning Roller by the ends.

Step 6. Position the ends of the Card Cleaning Roller in the slots. Push until the roller fully

seats and latches.

Step 7. Close the Printer’s Door.

Summary of content (10 pages)

PAGE 1
Installation and Setup Installing the Card Cleaning Roller Installing the Card Cleaning Roller The Card Cleaning Roller cleans the cards entering the Printer from either the Input Hopper or the Single-Feed Input. Step 1. Remove the Card Cleaning Roller from its packaging. To avoid contamination, always hold the roller by the ends. Step 2. Peel the protective wrapper from the Card Cleaning Roller. Step 3. Open the Printer Door by pressing the Door Release button on the top of the Printer. Step 4.
PAGE 2
Installation and Setup Loading the Transfer Film Loading the Transfer Film The ZXP Series 8 printer is designed to work only with Zebra True Colours® i Series™ Transfer Film for near photographic print resolution and over-the-edge printing. Step 1. Locate the transfer film supply spindles and the transfer film take-up spindles. Step 2. Unroll about one foot from the full roll of transfer film (supply spool), and wind it (2 wraps) onto the empty take-up spool.
PAGE 3
Installation and Setup Loading the Transfer Film Step 3. Load transfer film supply spool onto the supply spindles, green flange side to the left. Step 4. Load the empty take-up spool onto the take-up spindles, white flange side to the right. Step 5. Make sure the transfer film comes off the bottom of the supply spool and feeds to the bottom of the take-up spool. Step 6. The figure below shows the proper installation of the transfer film. 14 Zebra ZXP Series 8 Card Printer User’s Manual P1011091-001 Rev.
PAGE 4
Installation and Setup Loading a Print Ribbon Loading a Print Ribbon The ZXP Series 8 printer is designed to work only with Zebra True Colours® i Series™ Ribbons in order to achieve rich, vibrant, image production over the full-color spectrum. Step 1. Locate the print ribbon supply spindles and the print ribbon take-up spindles. Take-up Spindle GRAY Take-up Spool BLUE Take-up Spindle BLUE Flange Flange Supply Spool PURPLE Supply Spindle GRAY Supply Spindle PURPLE P1011091-001 Rev.
PAGE 5
Installation and Setup Loading a Print Ribbon Step 2. Load the print ribbon supply spool onto the supply spindles, purple flange side to the left. Step 3. Load the empty take-up spool onto the take-up spindle, blue flange side to the right. Step 4. Make sure the print ribbon comes off the bottom of the supply spool and feeds to the bottom of the take-up spool. Step 5. The figure below shows the proper installation of the print ribbon. 16 Zebra ZXP Series 8 Card Printer User’s Manual P1011091-001 Rev.
PAGE 6
Installation and Setup Connecting Power Connecting Power Electric Shock Caution • Limit AC power supplied to the Printer to 100 – 230 volts, 60 ~ 50 Hertz. Limit excess current draw to 16 amps or less, using an associated circuit breaker or other such device. Never operate the Printer in a location where operator, computer, or printer can get wet. Personal injury could result.
PAGE 7
Installation and Setup Connecting the Printer to your Computer Connecting the Printer to your Computer Connect the USB cable to the printer and the computer. Ethernet functionality requires a firmware upgrade to be activated. This firmware is pending release and will be available for download at www.zebracard.com. Please check our website occasionally for this and other upgrades. USB 18 Zebra ZXP Series 8 Card Printer User’s Manual P1011091-001 Rev.
PAGE 8
Installation and Setup Installing the Windows Printer Driver Installing the Windows Printer Driver Overview Each computer that will use the printer must have the Printer Driver installed. If not already done, connect power to the printer; ensure that the printer’s power switch in the OFF ( ) position, and connect the printer to the computer.
PAGE 9
Installation and Setup Installing the Windows Printer Driver Installing the USB Printer Driver Step 1. If not already done, connect power to the printer. Do not turn power ON. Step 2. Connect the USB port on the rear of the printer to the computer’s USB port. Step 3. Ensure that the Printer’s power switch in the OFF ( ) position. Step 4. Insert the User Documentation and Drivers CD into the CD drive of the host computer. The Main Menu will open. Step 5.
PAGE 10
Installation and Setup Installing the Windows Printer Driver Step 9. The InstallShield Wizard window will open. To proceed with the installation, click the Next button. Step 10. Select Install USB printer drivers, and click the Next button. Step 11. Ensure that the Printer’s power switch in the OFF ( OK button. P1011091-001 Rev.