User's Manual

ManualsBrandsZebra Technologies ManualsPOS EquipmentHands-Free Imager, BT Barcode Scanner

Table Of Contents

Warranty
Patents
Introduction
About this Guide
Unpacking the Imager
Cordless Configuration Features
Corded Configuration Features
- Change Trigger Position
Getting Started - Cordless Configuration
- Before using the Imager, charge the battery. The 8-Bay Battery Charger supports both standard and extended capacity batteries.
- Charge the Battery
- Install the Battery
- Remove the Battery
- Wear the Imager
Getting Started - Corded Configuration
- Connect Corded Adapter
- Remove the Corded Adapter
- Connect to a Wearable Terminal
- Wear the Imager
Status Indications
Bluetooth Connection
- Establish Bluetooth Connection
- Remove Bluetooth Connection
- Restore Lost Bluetooth Connection
Scan
- Scan Triggering Modes
  - Manual Triggering (Triggered models only)
  - Auto-triggering (Triggered models only)
- Aiming the Imager
Customize the Imager Behavior
Troubleshooting
Resetting the Imager
- Warm Boot
- Cold Boot
Field Replaceable Parts
- Comfort Pad Replacement
  - Removal
  - Installation
- Trigger Assembly Replacement
  - Removal
  - Installation
- Fingers Strap Replacement (Trigger Assembly)
  - Removal
  - Installation
- Fingers Strap Replacement (Triggerless Finger Clamp)
  - Removal
  - Installation
- Strap Buckle Replacement
  - Removal
  - Installation
Cleaning
Regulatory Information
- Bluetooth® Wireless Technology
- Wireless Device Country Approvals
Health and Safety Recommendations
- Ergonomic Recommendations
- Warnings for Use of Wireless Devices
  - Potentially Hazardous Atmospheres - Vehicles Use
- Safety in Hospitals
  - Pacemakers
  - Other Medical Devices
- RF Exposure Guidelines
- Laser Devices
  - Imager Labeling
Batteries
- Taiwan - Recycling
  - Battery Information
  - Battery Safety Guidelines
- Radio Frequency Interference Requirements-FCC
  - This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may no...
  - Radio Frequency Interference Requirements - Canada
- Marking and European Economic Area (EEA)
  - Statement of Compliance for Wireless Devices
- Japan (VCCI) - Voluntary Control Council for Interference
  - This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Eq...
- Korea Warning Statement for Class B ITE
  - Other Countries

Quick Reference Guide 11

Status Indications

The Imager has two Scan LEDs that provide identical indications. The Imager is

also equipped with a beeper that generates sound indications in variable tones.

NOTE In corded adapter configuration, beep indications are emitted only from the

WT4090.

Bluetooth Connection

Establish Bluetooth Connection

To establish Bluetooth connection with a mobile computer:

1. Ensure that the Imager is within a range of 10 meters (30 feet) from the mobile

computer.

2. Install the battery on the Imager.

No. LED Beep Indication Description

1. None High/low Bluetooth communication is

disconnected

2. Short green

flashes

None Attempting to connect over

Bluetooth

3. None Low/high Imager is connected over

Bluetooth

4. None High/low Bluetooth communication is

disconnected - Imager is out of

range

5. None high/low/high/low Properly decoded scan of

Bluetooth pairing Barcode

6. None Long low/

long high/

Bluetooth connection attempt

failed

7. None Long low/

long high/

Long low/

long high/

Bluetooth connection attempt is

rejected

8. One green

flash

High Proper scanning indication

9. None 4 long beeps No Bluetooth communication after

scanning time-out

QRG_507.fm Page 11 Wednesday, January 28, 2009 8:37 PM