User's Manual

We reserves the right to make changes to any product to improve
reliability, function, or design. We do not assume any product liability
arising out of, or in connection with, the application or use of any product,
circuit, or application described herein. No license is granted, either
expressly or by implication, estoppel, or otherwise under any patent right
or patent, covering or relating to any combination, system, apparatus,
machine, material, method, or process in which our products might be
used. An implied license exists only for equipment, circuits, and
subsystems contained in the products.
Warranty
For the complete hardware product warranty statement, go to: http://
www.zebra.com/warranty.
Service Information
If you have a problem using the equipment, contact your facility’s
Technical or Systems Support. If there is a problem with the equipment,
they will contact the Global Support Center at: http://www.zebra.com/
support.
For the latest version of this guide go to: http://www.zebra.com/support.
Zebra Technologies Corporation
3 Overlook Point
Lincolnshire, IL, U.S.A.
http://www.zebra.com
Zebra and the stylized Zebra head are trademarks of ZIH Corp.,
registered in many jurisdictions worldwide. All other trademarks are the
property of their respective owners.
© 2016 Symbol Technologies LLC, a subsidiary of Zebra Technologies
Corporation. All Rights Reserved.
MN-002960-01 Rev. A — January 2017
Touch Computer
TC70x
Regulatory Guide
More Information
Refer to the TC70x User Guide for Android Version X.X for more information
on using this device. Go to http://www.zebra.com/support.
Regulatory Information
This device is approved under Zebra Technologies Corporation.
This guide applies to the following Model Number TC700K.
All Zebra devices are designed to be compliant with the rules and regulations
in the locations they are sold and will be labeled as required.
Local language translations are available at the following website:
www.zebra.com/support.
Any changes or modifications to Zebra equipment, not expressly approved by
Zebra, could void the user’s authority to operate the equipment.
UL Listed Products with GPS
Underwriters Laboratories Inc. (UL) has not tested the performance or
reliability of the Global Positioning System (GPS) hardware, operating
software, or other aspects of this product. UL has only tested for fire, shock,
or casualties as outlined in UL's Standard(s) for Safety for Information
Technology Equipment, UL60950-1. UL Certification does not cover the
performance or reliability of the GPS hardware and GPS operating software.
UL makes no representations, warranties, or certifications whatsoever
regarding the performance or reliability of any GPS related functions of this
product.
Bluetooth
®
Wireless Technology
This is an approved Bluetooth
®
product. For more information or to view End
Product Listing, please visit https://www.bluetooth.org/tpg/listings,cfm
Wireless Device Country Approvals
Regulatory markings, subject to certification, are applied to the device
signifying the radio(s) is/are approved for use in the following countries:
United States, Canada, Japan, China, S. Korea, Australia, and Europe.
Please refer to the Zebra Declaration of Conformity (DoC) for details of other
country markings. This is available at www.zebra.com/doc.
Note: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
Country Roaming
This device incorporates the International Roaming feature (IEEE802.11d)
which will ensure the product operates on the correct channels for the
particular country of use.
Wi-Fi Direct
Wi-Fi Direct operation is limited to the following channels/bands as
supported in the country of use.
˙Channels 1-11 (2412-2462 MHz).
˙Channels 36 - 48 (5150-5250 MHz).
˙Channels 149 - 165 (5745-5825 MHz).
Frequency of Operation – FCC and IC
5 GHz Only
Industry Canada Statement
2.4 GHz Only
The available channels for 802.11 b/g operation in the US are Channels 1 to
11. The range of channels is limited by firmware.
Health and Safety Recommendations
Ergonomic Recommendations
• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
Vehicle Installation
RF signals may affect improperly installed or inadequately shielded electronic
systems in motor vehicles (including safety systems). Check with the
manufacturer or its representative regarding your vehicle. You should also
consult the manufacturer about any equipment that has been added to your
vehicle.
An air bag inflates with great force. DO NOT place objects, including either
installed or portable wireless equipment, in the area over the air bag or in the
air bag deployment area. If in-vehicle wireless equipment is improperly
installed and the air bag inflates, serious injury could result.
Position the device within easy reach. Be able to access the device without
removing your eyes from the road.
For Safe installation
• Do not put your phone in a location that obstructs the drivers vision or
interferes with the operation of the Vehicle.
• Do not cover an airbag.
Safety on the Road
Do not take notes or use the device while driving. Jotting down a “to do” list or
flipping through your address book takes attention away from your primary
responsibility, driving safely.
When driving a car, driving is your first responsibility - Give full attention to
driving. Check the laws and regulations on the use of wireless devices in the
areas where you drive. Always obey them.
When using a wireless device behind the wheel of a car, practice good
common sense and remember the following tips:
1. Get to know your wireless device and any features such as speed dial and
redial. If available, these features help you to place your call without
taking your attention off the road.
2. When available, use a hands free device.
3. Let the person you are speaking with know you are driving; if necessary,
suspend the call in heavy traffic or hazardous weather conditions. Rain,
sleet, snow, ice, and even heavy traffic can be hazardous.
4. Dial sensibly and assess the traffic; if possible, place calls when you are
not moving or before pulling into traffic. Try to plan calls when your car will
be stationary. If you need to make a call while moving, dial only a few
numbers, check the road and your mirrors, then continue.
5. Do not engage in stressful or emotional conversations that may be
distracting. Make people you are talking with aware you are driving and
suspend conversations that have the potential to divert your attention from
the road.
6. Use your wireless phone to call for help. Dial the Emergency services, (9-
1-1 in the US, and 1-1-2 in Europe) or other local emergency number in
the case of fire, traffic accident or medical emergencies. Remember, it is a
free call on your wireless phone! The call can be made regardless of any
security codes and depending on a network, with or without a SIM card
inserted.
7. Use your wireless phone to help others in emergencies. If you see an auto
accident, crime in progress or other serious emergency where lives are in
danger, call the Emergency Services, (9-1-1 in the US, and 1-1-2 in
Europe) or other local emergency number, as you would want others to do
for you.
8. Call roadside assistance or a special non-emergency wireless assistance
number when necessary. If you see a broken-down vehicle posing no
serious hazard, a broken traffic signal, a minor traffic accident where no
one appears injured, or a vehicle you know to be stolen, call roadside
assistance or other special non-emergency wireless number.
“The wireless industry reminds you to use your device / phone safely when
driving”.
Warnings for Use of Wireless Devices
Potentially Hazardous Atmospheres –
Vehicles Use
You are reminded of the need to observe restrictions on the use of radio
devices in fuel depots, chemical plants etc. and areas where the air contains
chemicals or particles (such as grain, dust, or metal powders) and any other
area where you would normally be advised to turn off your vehicle engine.
Safety in Aircraft
Switch off your wireless device whenever you are instructed to do so by
airport or airline staff. If your device offers a ‘flight mode’ or similar feature,
consult airline staff as to its use in flight.
Wireless devices transmit radio frequency energy and may affect medical
electrical equipment.
Wireless devices should be switched off wherever you are requested to do so
in hospitals, clinics or healthcare facilities. These requests are designed to
prevent possible interference with sensitive medical equipment.
Pacemakers
Pacemaker manufacturers recommended that a minimum of 15 cm (6 inches)
be maintained between a handheld wireless device and a pacemaker to
avoid potential interference with the pacemaker. These recommendations are
consistent with independent research and recommendations by Wireless
Technology Research.
Persons with Pacemakers:
• Should ALWAYS keep the device more than 15cm (6 inches) from their
pacemaker when turned ON.
• Should not carry the device in a breast pocket.
• Should use the ear furthest from the pacemaker to minimise the potential
for interference.
• If you have any reason to suspect that interference is taking place, turn
OFF your device.
Other Medical Devices
Please consult your physician or the manufacturer of the medical device, to
determine if the operation of your wireless product may interfere with the
medical device.
Safety Information
Reducing RF Exposure – Use Properly
Only operate the device in accordance with the instructions supplied.
International
The device complies with internationally recognized standards covering
human exposure to electromagnetic fields from radio devices. For information
on “International” human exposure to electromagnetic fields refer to the Zebra
Declaration of Conformity (DoC) at http://www.zebra.com/doc.
For further information on the safety of RF energy from wireless devices - see
https://www.zebra.com/us/en/about-zebra/company-information/corporate-
responsibility.html located under Corporate Responsibility.
Europe
Handheld Devices
This device was tested for typical body-worn operation. Use only Zebra
tested and approved belt-clips, holsters, and similar accessories to ensure
EU Compliance.
US and Canada
Phones (placed to ear or used with headset)
Use only Zebra tested and approved belt clips, holsters, and similar
accessories to ensure FCC Compliance. The use of third-party belt clips,
holsters, and similar accessories may not comply with FCC RF exposure
compliance requirements and should be avoided. The FCC has granted an
Equipment Authorization for these model phones with all reported SAR levels
evaluated as in compliance with the FCC RF emission guidelines. SAR
information on these model phones is on file with the FCC and can be found
under the Display Grant section of http://www.fcc.gov/oet/ea/fccid.
Co-located statement
To comply with FCC RF exposure compliance requirement, the antenna used
for this transmitter must not be co-located or operating in conjunction with any
other transmitter/antenna except those already approved in this filling.
Handheld Devices
This device was tested for typical body worn operation. Use only Zebra tested
and approved belt-clips, holsters, and similar accessories to ensure FCC
Compliance. The use of third-party belt clips, holsters, and similar
accessories may not comply with FCC RF exposure compliance
requirements, and should be avoided.
To satisfy US and Canadian RF exposure requirements, a transmitting device
must operate with a minimum separation distance of 1.5 cm or more from a
person's body.
Pour satisfaire aux exigences Américaines et Canadiennes d'exposition aux
radio fréquences, un dispositif de transmission doit fonctionner avec une
distance de séparation minimale de 1.5 cm ou plus de corps d'une personne.
Class 2 laser scanners use a low power, visible light diode. As with any very
bright light source such as the sun, the user should avoid staring directly into
the light beam. Momentary exposure to a Class 2 laser is not known to be
harmful.
The following statement is required to comply with US and international
regulations.
Scanner Labeling
Labels Read:
1. LASER LIGHT: DO NOT STARE INTO BEAM. CLASS 2 LASER
PRODUCT.
2. CAUTION - CLASS 2 LASER LIGHT WHEN OPEN. DO NOT STARE
INTO THE BEAM.
3. COMPLIES WITH 21CFR1040.10 AND 1040.11 EXCEPT FOR
DEVIATIONS PURSUANT TO LASER NOTICE NO. 50, DATED JUNE
24, 2007 AND IEC/EN 60825-1:2014
LED Devices
Classified as 'EXEMPT RISK GROUP' according to IEC 62471:2006 and EN
62471:2008.
Pulse duration: 1.7 ms.
Power Supply
Use ONLY a Zebra approved UL LISTED ITE (IEC/EN 60950-1, LPS) power
supply with electrical ratings: Output 5.4 VDC, min 3.0 A, with a maximum
ambient temperature of at least 50°C. Use of alternative power supply will
invalidate any approvals given to this unit and may be dangerous.
Batteries
Taiwan - Recycling
EPA (Environmental Protection
Administration) requires dry battery
producing or importing firms in
accordance with Article 15 of the
Waste Disposal Act are required to
indicate the recycling marks on the
batteries used in sales, giveaway or
promotion. Contact a qualified
Taiwanese recycler for proper battery disposal.
Battery Information
Use only Zebra approved batteries. Accessories which have battery charging
capability are approved for use with the following battery models:
• Model: BT-000318 (3.7 VDC, 4500 mAh)
Zebra rechargeable battery packs are designed and constructed to the
highest standards within the industry.
However, there are limitations to how long a battery can operate or be stored
before needing replacement. Many factors affect the actual life cycle of a
battery pack, such as heat, cold, harsh environmental conditions and severe
drops.
When batteries are stored over six (6) months, some irreversible deterioration
in overall battery quality may occur. Store batteries at half of full charge in a
dry, cool place, removed from the equipment to prevent loss of capacity,
rusting of metallic parts and electrolyte leakage. When storing batteries for
one year or longer, the charge level should be verified at least once a year
and charged to half of full charge.
Replace the battery when a significant loss of run time is detected.
Standard warranty period for all Zebra batteries is one year, regardless if the
battery was purchased separately or included as part of the mobile computer
or bar code scanner. For more information on Zebra batteries, please visit:
http://www.zebra.com/batterybasics.
Battery Safety Guidelines
The area in which the units are charged should be clear of debris and
combustible materials or chemicals. Particular care should be taken where
the device is charged in a non commercial environment.
• Follow battery usage, storage, and charging guidelines found in the user's
guide.
• Improper battery use may result in a fire, explosion, or other hazard.
• To charge the mobile device battery, the battery and charger temperatures
must be between +32°F and +104°F (0°C and +40°C).
• Do not use incompatible batteries and chargers. Use of an incompatible
battery or charger may present a risk of fire, explosion, leakage, or other
hazard. If you have any questions about the compatibility of a battery or a
charger, contact Zebra support.
• For devices that utilize a USB port as a charging source, the device shall
only be connected to products that bear the USB-IF logo or have
completed the USB-IF compliance program.
• Do not disassemble or open, crush, bend or deform, puncture, or shred.
• Severe impact from dropping any battery-operated device on a hard
surface could cause the battery to overheat.
• Do not short circuit a battery or allow metallic or conductive objects to
contact the battery terminals.
• Do not modify or remanufacture, attempt to insert foreign objects into the
battery, immerse or expose to water or other liquids, or expose to fire,
explosion, or other hazard.
• Do not leave or store the equipment in or near areas that might get very
hot, such as in a parked vehicle or near a radiator or other heat source.
Do not place battery into a microwave oven or dryer.
• Battery usage by children should be supervised.
• Please follow local regulations to promptly dispose of used re-chargeable
batteries.
• Do not dispose of batteries in fire.
• Seek medical advice immediately if a battery has been swallowed.
• In the event of a battery leak, do not allow the liquid to come in contact
with the skin or eyes. If contact has been made, wash the affected area
with large amounts of water and seek medical advice.
• If you suspect damage to your equipment or battery, contact Zebra
support to arrange for inspection.
Hearing Aid Compatibility
This device is in compliance with the applicable requirements of IC CS-03-
Part V.
Radio Frequency Interference
Requirements-FCC
Note: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. However there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Radio Frequency Interference Requirements-
Canada
CAN ICES-3 (B)/NMB-3(B)
Radio Transmitters
This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions: (1) This device may not
cause interference; and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radio électrique subi
même si le brouillage est susceptible d'en compromettre le fonctionnement.
For RLAN Devices:
The use of 5 GHz RLAN’s, for use in Canada, have the following restrictions:
• Restricted Band 5.60 – 5.65 GHz
Pour les équipements RLAN:
L'utilisation de la bande RLAN 5 GHz au Canada présente les limitations
suivantes :
• Bande restreinte 5.60 - 5.65 GHz
Label Marking: The Term “IC:” before the radio certification only signifies that
Industry Canada technical specifications were met.
Etiquette de marquage: Le terme “IC” avant la certification radio signifie que
le produit est compatible avec le spécification Industrie Canada.
The use of RLAN’s, for use through the EEA, have the following restrictions:
• Maximum radiated transmit power of 100 mW EIRP in the frequency
range 2.400 - 2.4835 GHz.
• 5150 - 5350 MHz is restricted to indoor use only.
Bluetooth
®
Wireless Technology for use through the EEA has the following
restrictions:
• Maximum radiated transmit power of 100mW EIRP in the frequency range
2.400 - 2.4835 GHz.
CAUTION Only use Zebra approved and UL Listed accessories,
battery packs and battery chargers.
Do NOT attempt to charge damp/wet mobile computers or batteries. All
components must be dry before connecting to an external power
source.
Declared maximum operating temperature: 50°C.
Operation of the device without regulatory approval is illegal.
CAUTION The device for the band 5150-5250 MHz is only for
indoor usage to reduce potential for harmful interference to co-
Channel mobile satellite systems. High power radars are
allocated as primary users (meaning they have priority) of 5250-
5350 MHz and 5650-5850 MHz and these radars could cause
interference and/or damage to LE-LAN devices.
AVERTISSEMENT Le dispositive fonctionnant dans la
bande 5150-5250 MHz est réservé uniquement pour une
utilisation à l'intérieur afin de réduire les risques de
brouillage préjudiciable aux systèmes de satellites mobiles
utilisant les mêmes canaux. Les utilisateurs de radars de
haute puissance sont désignés utilisateurs principaux (c.-à-
d., qu'ils ont la priorité) pour les bands 5250-5350 MHz et
5650-5850 MHz et que ces radars pourraient causer du
brouillage et/ou des dommages aux dispositifs LAN-EL.
CAUTION In order to avoid or minimize the potential risk of
ergonomic injury follow the recommendations below. Consult with
your local Health & Safety Manager to ensure that you are adhering to
your company's safety programs to prevent employee injury.
NOTE Connection to an alert device that will cause a vehicle
horn to sound or lights to flash on receipt of a call on public
roads is not permitted.
IMPORTANT Before installing or using, check state and local
laws regarding windshield mounting and use of equipment.
CAUTION Please observe all warning notices with regard to
the usage of wireless devices.
Safety in Hospitals
RF Exposure Guidelines
Laser Devices
CAUTION Use of controls, adjustments, or the performance of
procedures other than those specified herein may result in
hazardous laser light exposure.
CAUTION- CLASS 2 LASER LIGHT WHEN OPEN.
DO NOT STARE INTO THE BEAM.
ATTENTION- LUMIÉRE LASER DE CLASSE 2 EN
CAS D'OUVERTURE.
NE PAS REGARDER DANS LE FAISCEAU.
VORSICHT- LASERLICHT KLASSE 2,
WENN ABDECKUNG GEÖFFNET.
NICHT IN DEN STRAHL BLICKEN.
3
2
1
COMPLIES WITH 21CFR1040.10 AND 1040.11 EXCEPT
FOR DEVIATIONS PURSUANT TO LASER NOTICE
NO. 50, DATED JUNE 24, 2007 AND IEC/EN
60825-1:2014
CAUTION Risk of explosion if battery is replaced by an incorrect
type. Dispose of batteries according to instructions.
Marking and European Economic
Area (EEA)
Review Copy