Enhanced Wireless Router User’s Guide Version 3.0 Copyright 2003-2004, MeshNetworks, Inc.
MEA EWR User’s Guide Foreword This document describes in detail the confidential and proprietary technology of MeshNetworks’ MEA™ Architecture. MeshNetworks’ products and technology are protected by US and international patent and patent pending technology. This document represents the current MEA design; the contents are subject to change at any time at the discretion of MeshNetworks, Inc. MEA, MeshTray, and MeshNetworks’ logo are trademarks or registered trademarks of MeshNetworks, Inc.
MEA EWR User’s Guide Table of Contents 1 2 ENHANCED WIRELESS ROUTER....................................................................................... 1 1.1 Introduction................................................................................................................. 1 1.2 What’s in the Box ....................................................................................................... 1 INSTALLATION REQUIREMENTS..............................................................
MeshNetworks 3.1.4.4 3.1.5 Restoring Factory Defaults – Normal Operations............................................ 19 3.1.6 Changing the Web Password .......................................................................... 21 3.1.7 Upgrading the Device Firmware ...................................................................... 23 3.2 External Device Provisioning .................................................................................. 25 3.2.1 Infrastructure Requirements .........
MEA EWR User’s Guide List of Figures Figure 2-1. EWR6300 Identification Label ............................................................................3 Figure 2-2. EWR6300 External Connection Points ..............................................................4 Figure 2-3 Typical EWR Depoyment ....................................................................................5 Figure 3-1. Enter Network Password Initial Web Page Authentication Dialog .................8 Figure 3-2.
MEA EWR User’s Guide 1 Enhanced Wireless Router 1.1 Introduction Thank you for purchasing the MEA Enhanced Wireless Router (EWR). MEA is a wireless communication system capable of supporting high data rate mobile communication at variable rates of vehicular speeds. The Enhanced Wireless Router (EWR™) is designed to be deployed outdoors for wireless coverage in large geographic areas to wireless network access to one or more IP devices via its built-in RJ45 Ethernet port.
MeshNetworks 2.1 Enhanced Wireless Router (EWR) The MEA Enhanced Wireless Router 6300 (EWR6300) is an infrastructure device positioned in a fixed location, such as on a pole, wall, or rooftop. The EWR6300 requires professional installation to ensure the installation is performed in accordance with FCC licensing regulations. The EWR6300 provides range extension, a means to route around obstructions, a fixed location reference for use in Geo-Location, and the capability of enabling IP devices.
MEA EWR User’s Guide 2.1.2 Record MAC Address of the EWR6300 The transceiver Media Access Control (MAC) address is recorded on the label located on the antenna end of the EWR6300 and the Ethernet MAC address is recorded on the label located on the antenna end of the EWR6300 as show in Figure 2-1. Record the MAC Address and ETH MAC Address in the tables in Section 3.4.1, because it will be required later to configure and test the device. ETH MAC Address MAC Address Figure 2-1.
MeshNetworks 2.1.3 EWR6300 Assembly Figure 2-2 shows the external connection points on a EWR6300 box. Antenna Connector Power Out (3-pin) Power In (4-pin) (optional) Test Port RJ45 (Data) Port (Not Shown) Figure 2-2. EWR6300 External Connection Points Assemble the EWR using the following procedure: 1. If desired, mount the EWR box using the enclosed bracket. Refer to the EWR6300 Mounting Bracket section. 2. Insert the Antenna into the N-type Connector on the top of the box, and rotate to close. 3.
MEA EWR User’s Guide Figure 2-3 Typical EWR Depoyment 2.1.5 Deployment Tips Locate the antenna to minimize multipath: • Minimize interference from nearby transmitters • Maximize chance of a direct line of sight connection to other devices • The antenna supplied is designed to be mounted vertically The devices are designed to be vertically mounted with the antenna port at the top or the bottom. The antenna is specified around deployment heights of 3-30 meters.
MeshNetworks A response to the ping command verifies that the transceiver is communicating. NOTE: If you are running an EWR as a standalone device, the configuration web page can be reached by connecting a PC to the wired interface.
MEA EWR User’s Guide 3 Installing the MEA Enhanced Wireless Router 3.1 Device Administration: Configuring the EWR Devices The EWR provides network access to one or more IP devices connected to the Ethernet port of the EWR. In order for the EWR to provide service to the IP devices, some configuration must be set up prior to connecting the IP devices. The EWR serves as a default gateway for the attached IP devices.
MeshNetworks Once the web browser is directed to the web page of the EWR, you will be prompted for a username and password. A dialog box similar to the following should show up if you are using Internet Explorer: Figure 3-1. Enter Network Password Initial Web Page Authentication Dialog The username is admin, and the default (initial) password is admin. The password for the admin account should be changed during installation.
MEA EWR User’s Guide After the login authentication has been completed, the web browser will display a redirecting page, and your browser will automatically transition to the home web page for MEA Device Administration. Figure 3-2.
MeshNetworks Figure 3-3. MEA Device Administration Home Page (Super User Login) The MEA Device Administration home page provides you with some basic information about the device, including the IP addresses assigned to the device, the MAC addresses of the device, the firmware revision number, and the reported link quality for the link to the IAP.
MEA EWR User’s Guide 3.1.2 Configuring the Device Once you have accessed the MEA Device Administration home page, click on the Configuration tab to display the IP address configuration. Figure 3-4. EWR Device Administration Configuration Page (Super User Login) The EWR Device Administration (Super User Login) page will allow you to change the configuration of the EWR. The fields displayed on this page are described below.
MeshNetworks Field Name Field Description Field Default Value MeshManager RDATE Server IP Address The IP address of the RDATE server. This is 172.31.0.20 usually the MiSC when operating in infrastructure mode. The RDATE server provides the current date to the EWR. The EWR can operate without an RDATE server.
MEA EWR User’s Guide The server may be configured by the operator to hand out temporary or static leases. The EWR must associate and acquire an address from the network before establishing communications. Once a lease has been granted, the address may be dragged out of network coverage for the remainder of the lease or, if a static lease was granted, until the next power cycle.
MeshNetworks 3.1.2.5 Setting the User Supplied IP Address In order to set the user-supplied IP address for the EWR, the User-Supplied radio button must be selected. At that point, the user may enter an IP address, subnet mask consistent with the existing network. The user should also enter the IP address of the default gateway and DNS server, as well as enter the domain name. Note that this configures the user-supplied address for the EWR device.
MEA EWR User’s Guide Figure 3-6. System Update Save Completed Web Page After the settings have been saved, click the Finished button. Your web browser should return to the MEA Device Administration home page. A reboot of the device is not required for the changes to take effect.
MeshNetworks 3.1.3 Resetting the EWR Although you should not have to reset the EWR device, the device can be commanded to reset via the web pages. In order to reset the device, return to the MEA Device Administration home page, and click on the Reset the Device link in the Device Management panel. The web page displayed will allow you to reset the device. Figure 3-7. Device Reset Prompt Web Page Once you have commanded the device to reset, the following screen will be displayed.
MEA EWR User’s Guide Figure 3-8. Device Reset in Progress Web Page NOTE: After the completion of the reset, you may experience a significant delay when bringing up another web page. Please be patient.
MeshNetworks 3.1.4 Restoring Factory Settings – User Supplied Mode Limitations NOTE: 3.1.4.1 In Release 3.0, there is a known issue that arises if the selected device addressing mode is User-Supplied when the user restores the factory default settings for the EWR. The following options are offered as a way to recover from this limitation. EWR Reset-to-Default Recovery In User-Supplied Mode The factory default settings for the User-Supplied parameters cannot be routed (i.e. 0.0.0.0).
MEA EWR User’s Guide 3.1.5 Restoring Factory Defaults – Normal Operations When the Restore Factory Defaults function is selected from the EWR Device Administration Home Page, the device will present the following web page: Figure 3-9. Restore Factory Settings Web Page The Restore Factory Defaults function allows the operator to return the device to factory defaults. This change will include the web password for the administrator and access accounts.
MeshNetworks Figure 3-10. Confirm Changes Window for Restore Factory Settings The Factory Settings Restored page will be displayed. Figure 3-11. Factory Settings Restored Web Page Click on the Finished button to complete the reset procedure.
MEA EWR User’s Guide 3.1.6 Changing the Web Password When the Change Admin Password function is selected from the EWR Device Administration Home Page by the administrator, or the Change User Password function is selected, the device will present the following web page: Figure 3-12. Enter New Password Web Page The operator is expected to enter a new password for the web account and click on the “Submit” button.
MeshNetworks Figure 3-13. Confirm Changes Window for Enter New Password When the operator confirms the change, the new password will be stored in flash, and the device will present a status screen indicating that the change was successful. Figure 3-14.
MEA EWR User’s Guide 3.1.7 Upgrading the Device Firmware The web interface for the device also provides the ability to upgrade the firmware on-site. To use this feature, you must have an upgrade file from a released upgrade package. When the Upgrade Device Firmware function is selected from the EWR Device Administration Home Page, the device will present the following web page: Figure 3-15. Update Device Firmware Web Page This page allows entry of the name (and path) of the upgrade file.
MeshNetworks Figure 3-16. Confirm Upload Window for Firmware Update Once the filename has been confirmed, the web browser will transmit the file to the device, and the device will present an upgrade progress screen. This page will indicate the current stage in the upgrade process. Figure 3-17. Firmware Upload Progress Web Page Once the upgrade is completed, the device must be reset. The Finished button will transition the web browser to the reset screen.
MEA 3.2 EWR User’s Guide External Device Provisioning Figure 3-18. External Device Provisioning Table The External Device Provisioning table is used to configure addresses for the attached nodes on the local ethernet segment. Up to three addresses are provisioned. The Enable checkbox indicates this row contains a valid address. Any address can be disabled by clearing the checkbox.
MeshNetworks The IP addresses default to values based on the transceiver MAC address of the device. The derivation is described below. By default, only the first IP address is enabled (for local-DHCP), and no addresses are reserved for specific MAC addresses. Please make sure to check the checkbox for the client IP addresses you have entered. Client 2 and Client 3 are not enabled by default. In this example, the EWR wired interface is assigned the IP address 172.16.2.1.
MEA 3.4 EWR User’s Guide EWR6300 Mounting Bracket The mounting bracket for the IAP6300 and the MWR6300 are identical to mounting bracket for the EWR6300. The bracket is robust secure; and can be used for horizontal, vertical, and offangle pole mounted installations. The mounting bracket is preinstalled and supplied with two 3 1/2 x 1/4 inch stainless steel bolts. The mounting bracket can accommodate up to a 3 1/4 inch diameter mounting pole.
MeshNetworks 3 1/2 x 1/4 inch bolt 1/4 Flat Washer 1/4 Flat Washer 1/4 Lock Washer 1/4 Hex Nut Note: All Hardware is Stainless Steel Figure 3-20. C-Clamp Bracket Assembly 3. Position the bracket in the desired location and securely tighten the two bracket bolts. 4. If required, loosen the Pivot Bolt and the Angle Locking Bolt (Figure 3-18) so that the antenna connector is positioned vertically. 5. Tighten the Angle Locking Bolt using a #1 Phillips screwdriver. 6.
MEA EWR User’s Guide 6 x 32 x 3/4 Angle Locking Bolt 1/4 x 1 inch Pivot Bolt (Requres 7/16 Wrench) Figure 3-21. EWR Pivot and Angle Locking Bolts NOTE: Some IAP6300 and MWR6300 enclosures may have a bolt or plug in the center of the back of the box. To maintain the integrity of the box, DO NOT REMOVE THIS PLUG. 3.4.1 EWR MAC Addresses This table has been included for recording the Ethernet MAC address and transceiver MAC address for a set of EWR devices as a quick reference.
MeshNetworks 4 License and Warranty Information 4.1 Important Information PLEASE READ CAREFULLY THE FOLLOWING BEFORE INSTALLING OR USING THIS HARDWARE, CONSISTING OF A CD ROM AND PCMCIA CARD, AND THE SOFTWARE (COLLECTIVELY, THE “PRODUCT”). IF YOU AGREE WITH ALL OF THE TERMS OF THIS LICENSE AGREEMENT & LIMITED WARRANTY, PROCEED WITH THE INSTALLATION AND USE OF THE PRODUCT FOLLOWING THE ONSCREEN INSTRUCTIONS. IF YOU DO NOT AGREE, DO NOT INSTALL OR USE THE PRODUCT.
MEA EWR User’s Guide You assume responsibility for the selection of the appropriate applications program and associated reference materials. MeshNetworks makes no warranty or representation that the Software will meet your requirements or work in combination with any hardware or applications software products provided by third parties, that the operation of the Software will be uninterrupted or error free, or that all defects in the Software will be corrected.
MeshNetworks 5 FCC Regulatory Information 5.1 FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation. The EWR6300 (Enhanced Wireless Router) is an infrastructure device that is positioned at a fixed location such as a building rooftop.
MEA EWR User’s Guide 6 Safety Information for the MEA Products The Federal Communications Commission (FCC) with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. MeshNetworks’ MEA products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991.
MeshNetworks Products covered - IAP6300, EWR6300 , WMC6300, and MWR6300 ETSI EN 301 489-1 (2002-08) and 301 489-17 Products covered - IAP6300, EWR6300 , WMC6300, and MWR6300 EN 55022:1998 and EN 55024:1998 Products covered - IAP6300, EWR6300 , WMC6300, and MWR6300 CENELEC EN 50360 and EN50371 – Specific Absorption Test - SAR Products covered - WMC6300 The following countries are covered under the CE Mark: Austria, Belgium, Demark, Finland, Germany, Greece, Ireland, Italy, Luxemburg, Netherlands, Portugal, S
