User Manual
Table Of Contents
- Contents
- About This Document
- Introduction
- Installation
- Getting Started
- Before You Begin
- Printing a Configuration Label — External ZebraNet 10/100 Print Server
- Printing a Network Configuration Label — Internal ZebraNet 10/100 Print Server and Wireless Print Servers
- Configuration of Wireless Securities
- View Wireless Status through the Control Panel
- Determining the Active Print Server
- Assigning an IP Address on any Print Server
- Setting and Monitoring Alerts on Any Print Server
- Checking Print Server Configuration Settings
- Enabling Protocols
- Defaulting ALL Print Servers
- Using WebView
- Using ZebraNet Bridge
- Using a ZPL Command
- Defaulting the ZebraNet 10/100 Print Server on the 105SL, S4M, PAX4, and External Devices
- Defaulting the Wireless Print Server on the S4M
- Defaulting the Print Servers on the ZM400 and ZM600 Printers
- Defaulting the Print Servers on the ZP Series, LP/TLP 2824 Plus, and G-Series Printers
- Defaulting the Print Servers on the HC100 Printers
- Defaulting the Print Servers on the 105SL, PAX4, Xi4, ZE500, and 105SLPlus Printers
- Defaulting the Print Servers on the ZD500R, ZT210, ZT220, ZT230, ZT410, and ZT420 Printers
- Defaulting the Print Servers on the ZD500R, ZT230, ZT410, and ZT420 Printers via the Control Panel
- Printing Queues
- Using Printing Protocols
- ZebraLink WebView
- Print Server Web Pages
- Control Panel
- Hardware Troubleshooting
- Troubleshooting the External 10/100 Print Server
- Troubleshooting the Internal ZebraNet 10/100 Print Server
- Troubleshooting the Wireless Print Server
- ZebraNet Bridge Discovery or Configuration Problems
- Unable to Print
- Unable to Configure Device
- HP JetAdmin or HP Web JetAdmin
- Wireless Error Messages
- General Wireless Issues
- Encryption and Authentication Issues
- IP Issues
- Frequently Asked Questions
- Glossary
- Index
137
Hardware Troubleshooting
Troubleshooting the Internal ZebraNet 10/100 Print Server
11/21/13 P1043301-005
Troubleshooting the Internal ZebraNet 10/100 Print
Server
Resetting the Internal ZebraNet 10/100 Print Server to Factory
Defaults
Which model printer do you have?
Internal ZebraNet 10/100 Print Server Network Status and Activity
Indicators
For the S4M, 105SL, and PAX4 Printers/Print Engines
Alongside of the RJ45 connector, there are two LED’s containing a red element and a green
element. By turning on and off different combinations of these two LED elements, the LED
indicates Ethernet links, activity, and speed.
If you have a… Then…
ZM400 or ZM600
printer
Go to Defaulting the Print Servers on the ZM400 and ZM600
Printers on page 77.
G-Series, ZP Series, or
LP/TLP 2824 Plus
printer
Go to Defaulting the Print Servers on the ZP Series, LP/TLP
2824 Plus, and G-Series Printers on page 77.
HC100 printer Go to Defaulting the Print Servers on the HC100 Printers
on page 78.
105SL, PA X 4,
Xi4, ZE500, and
105SLPlus
printer/print engine
Go to Defaulting the Print Servers on the 105SL, PAX4, Xi4,
ZE500, and 105SLPlus Printers on page 78.
ZT210 and ZT220
printer
Go to Defaulting the Print Servers on the ZD500R, ZT210,
ZT220, ZT230, ZT410, and ZT420 Printers on page 79.
ZT230 printer Go to Defaulting the Print Servers on the ZD500R, ZT230,
ZT410, and ZT420 Printers via the Control Panel on page 79.
Network Status LED State Description
Off No Ethernet link detected
Amber 10 Mbps link detected
Amber, blinking 10 Mbps link detected and Ethernet activity detected
Green 100 Mbps link detected
Green, blinking 100 Mbps link detected and Ethernet activity detected