User Manual
Table Of Contents
- Contents
- About This Document
- Introduction
- Installation
- Getting Started
- Before You Begin
- Printing a Configuration Label — External ZebraNet 10/100 Print Server
- Printing a Network Configuration Label — Internal ZebraNet 10/100 Print Server and Wireless Print Servers
- Configuration of Wireless Securities
- View Wireless Status through the Control Panel
- Determining the Active Print Server
- Assigning an IP Address on any Print Server
- Setting and Monitoring Alerts on Any Print Server
- Checking Print Server Configuration Settings
- Enabling Protocols
- Defaulting ALL Print Servers
- Using WebView
- Using ZebraNet Bridge
- Using a ZPL Command
- Defaulting the ZebraNet 10/100 Print Server on the 105SL, S4M, PAX4, and External Devices
- Defaulting the Wireless Print Server on the S4M
- Defaulting the Print Servers on the ZM400 and ZM600 Printers
- Defaulting the Print Servers on the ZP Series, LP/TLP 2824 Plus, and G-Series Printers
- Defaulting the Print Servers on the HC100 Printers
- Defaulting the Print Servers on the 105SL, PAX4, Xi4, ZE500, and 105SLPlus Printers
- Defaulting the Print Servers on the ZD500R, ZT210, ZT220, ZT230, ZT410, and ZT420 Printers
- Defaulting the Print Servers on the ZD500R, ZT230, ZT410, and ZT420 Printers via the Control Panel
- Printing Queues
- Using Printing Protocols
- ZebraLink WebView
- Print Server Web Pages
- Control Panel
- Hardware Troubleshooting
- Troubleshooting the External 10/100 Print Server
- Troubleshooting the Internal ZebraNet 10/100 Print Server
- Troubleshooting the Wireless Print Server
- ZebraNet Bridge Discovery or Configuration Problems
- Unable to Print
- Unable to Configure Device
- HP JetAdmin or HP Web JetAdmin
- Wireless Error Messages
- General Wireless Issues
- Encryption and Authentication Issues
- IP Issues
- Frequently Asked Questions
- Glossary
- Index
Index
158
P1043301-005 11/21/13
configuration label
default gateway
45, 48
fields to know for external wired print server
45
fields to know for internal wired print server
48
hardware address
45
IP address
45, 48
MAC address
45, 48
serial number
45
subnet mask
45, 48
to print an internal wired print server
46
to print external wired print server
44
configuration methods
wireless securities
51
configuration page
print server status
120
configuration problems
troubleshooting
140
configuration settings
browser
69
check using WebView
69
check using ZebraNet Bridge
68
configure wireless print server
through Network Setup Wizard
51
through Set/Get/Do (SGD) command
51
through ZPL command
51
control panel
menu options
126
view wireless status
52
create new item
directory listing
106
D
default
password
43
user ID
43
default gateway
configuration label
45, 48
default print servers to factory settings
using WebView
75
using ZebraNet Bridge
76
default to factory settings
print servers
75
default wired print server to factory settings
105SL printers
76
external wired device
76
HC100 printers
78
PAX4 print engines
76
S4M printers
76
Xi4 printers
78
ZM400 and ZM600 printers
77
ZT210, ZT220, ZT230 printers
79
default wired print server to factory settings via the
control panel
ZT230 printers
79
default wireless print server to factory settings
HC100 printers
78
S4M printers
77
Xi4 printers
78
ZM400 and ZM600 printers
77
ZT210, ZT220, ZT230 printers
79
default wireless print server to factory settings via the
control panel
ZT230 printers
79
device type
107
directory listing
to create new item
106
to view
105
WebView
105
discovery problems
troubleshooting
140
E
enable
protocols
72
enabled protocols
print server configuration menu
115
encryption
troubleshooting
145
external ZebraNet 10/100 Print Server
illustration
35
install
36
installation instructions
34
specifications
29
F
FAQ’s 147
File Transfer Protocol
87
firmware
connection problems after upgrade
143
requirements for wired print servers
25
requirements for wireless print servers
27
upgrade
34
flash memory
107
FTP
87
G
general setup
WebView
95
gleaning
assign an IP address
63