User Manual
Table Of Contents
- Contents
- About This Document
- Introduction
- Installation
- Getting Started
- Before You Begin
- Printing a Configuration Label — External ZebraNet 10/100 Print Server
- Printing a Network Configuration Label — Internal ZebraNet 10/100 Print Server and Wireless Print Servers
- Configuration of Wireless Securities
- View Wireless Status through the Control Panel
- Determining the Active Print Server
- Assigning an IP Address on any Print Server
- Setting and Monitoring Alerts on Any Print Server
- Checking Print Server Configuration Settings
- Enabling Protocols
- Defaulting ALL Print Servers
- Using WebView
- Using ZebraNet Bridge
- Using a ZPL Command
- Defaulting the ZebraNet 10/100 Print Server on the 105SL, S4M, PAX4, and External Devices
- Defaulting the Wireless Print Server on the S4M
- Defaulting the Print Servers on the ZM400 and ZM600 Printers
- Defaulting the Print Servers on the ZP Series, LP/TLP 2824 Plus, and G-Series Printers
- Defaulting the Print Servers on the HC100 Printers
- Defaulting the Print Servers on the 105SL, PAX4, Xi4, ZE500, and 105SLPlus Printers
- Defaulting the Print Servers on the ZD500R, ZT210, ZT220, ZT230, ZT410, and ZT420 Printers
- Defaulting the Print Servers on the ZD500R, ZT230, ZT410, and ZT420 Printers via the Control Panel
- Printing Queues
- Using Printing Protocols
- ZebraLink WebView
- Print Server Web Pages
- Control Panel
- Hardware Troubleshooting
- Troubleshooting the External 10/100 Print Server
- Troubleshooting the Internal ZebraNet 10/100 Print Server
- Troubleshooting the Wireless Print Server
- ZebraNet Bridge Discovery or Configuration Problems
- Unable to Print
- Unable to Configure Device
- HP JetAdmin or HP Web JetAdmin
- Wireless Error Messages
- General Wireless Issues
- Encryption and Authentication Issues
- IP Issues
- Frequently Asked Questions
- Glossary
- Index
Index
162
P1043301-005 11/21/13
reset internal wired print server to factory defaults
137
reset wireless print server to factory defaults
139
system disabled after encryption set
145
unable to configure device
142
unable to print
140
using telnet
141
WEP key field not large enough
145
wireless error messages
142
wireless print server
139
wireless radio card not acknowledged
143
WPA mode
145
U
unable to configure device
troubleshooting
142
upgrade
firmware
34
user ID
default
43
V
view
directory listing
105
port status of print server
121
printer configuration
92
printer controls
110
view and modify printer settings
advanced setup
99
calibration
98
general setup
95
media setup
98
network communications setup
96
print listings on label
96
RFID setup
97
serial communications setup
95
WebView
93
ZPL control
99
W
web admin settings
print server configuration menu
118
web pages
problems accessing with wired IP address
146
WebView
90
advanced setup
99
calibration
98
check configuration settings
69
default print servers to factory settings
75
directory listing
105
enabled protocols
72
general setup
95
home page
90
media setup
98
network communications setup
96
network configuration screens
100
primary/secondary settings
101
print listing on label
96
print server features
112
print server status
120
printer configuration
92
printer controls
110
reset print server
122
restore print server
123
RFID setup
97
serial communications setup
95
setting alerts
66
SMTP settings
102
SNMP settings
101
TCP/IP settings for X60.15.x and ZSPx
102
TCP/IP settings for Xi4 Series, ZM Series, RZ
Series
103
view and modify printer settings
93
view printer configuration settings
92
view printer controls
110
wireless encryption setup settings
104
wireless setup settings
104
ZPL control
99
wired and wireless print servers
both installed
57
wired print server
check during bootup
58
printer requirements
22
wired print servers
supported services
16
wireless encryption setup settings
WebView
104
wireless error messages
troubleshooting
142