Zebra® P430i Card Printer User’s Manual 980470-001 Rev.
lor ed Co l-Sid Dua
Foreword This manual contains installation and operation information for the Zebra P430i Card Printers manufactured by Zebra Technologies Corporation, Camarillo, California. Return Materials Authorization Before returning any equipment to Zebra Technologies Corporation for in-warranty or out-of-warranty repair, contact Repair Administration for a Return Materials Authorization (RMA) number. Repack the equipment in the original packing material and mark the RMA number clearly on the outside.
Foreword Copyright Notice © 2006 ZIH Corp. This document contains information proprietary to Zebra Technologies Corporation. This document and the information contained within is Copyrighted by Zebra Technologies Corporation and may not be duplicated in full or in part by any person without written approval from Zebra.
Foreword 89/336/EEC EMC Directive EN 55022 (1998) EMC Directive EN 301489-3 V1.4.1 EMC Directive EN55024 (2001) 73/23/EEC modified by 93/68/EEC Low voltage Directive EN 60950-1 (2001) Product safety 1999/5/CE R&TTE Directive EN300330-2 V1.1.
Foreword P430i Printer Model The Zebra Product Number tells a story: Here is a quick review of the Zebra Card Printer Series numbering and lettering system to help you.
Foreword Note • Indicates information that emphasizes or supplements important points of the main text. Important • Advises you of information that is essential to complete a task, or points out the importance of specific information in the text. Provides an example or scenario to demonstrate or clarify a section of text. Electrostatic Discharge Caution • Warns you of the potential for electrostatic discharge. Electric Shock Caution • Warns you of a potential electric shock situation.
Foreword lor ed Co l-Sid Dua vi P430i User’s Manual 980470-001 Rev.
Table of Contents 1 • Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Printer Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Controls, Connectors, and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents 4 • Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Cleaning the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . When to Clean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to Clean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents • Smart Card Contact Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Smart Card Contact Station Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Printer Sharing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 • Connecting to a Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents lor ed Co l-Sid Dua x P430i User’s Manual 980470-001 Rev.
1 Introduction Thank you for choosing the Zebra P430i Card Printer. This manual guides you to efficient start up and operation of your new Card Printer. Printer Features The following shows the main functional features found on your P430i Printer.
Introduction Controls, Connectors, and Indicators Controls, Connectors, and Indicators Your P430i Printer has an LCD Display Panel and a Panel Button on the front and a power connector, power switch, and interface connector(s) on the rear panel.
Introduction Controls, Connectors, and Indicators LCD Panel The LCD Panel can display the following messages: Message Mode Operational Initializing Scrolling SELF TEST Scrolling READY Fixed DOWNLOADING DATA Fixed PRINTING MONO Fixed MAG ENCODING Fixed CONTACT ENCODING Fixed CONTACTLESS ENCODING Scrolling PRINTING CYAN Fixed PRINTING YELLOW Fixed PRINTING MAGENTA Fixed PRINTING BLACK Fixed PRINTING OVERLAY Fixed DOWNLOADING FW Fixed Warnings (Printer will still Operate) CLEAN
Introduction Controls, Connectors, and Indicators Message Mode CLEANING PRINTER Blinking Errors (Printer will not operate) 4 BROKEN RIBBON Blinking OUT OF RIBBON Blinking MECHANICAL ERROR Blinking OUT OF CARDS Blinking PRINT HEAD OPEN Blinking CHECK RIBBON Blinking REJECT BOX FULL Blinking LID OPEN Fixed COMMAND ERROR Blinking P430i User’s Manual 980470-001 Rev.
2 Installation and Setup General Information This section will guide you through the installation and setup of your P430i Card Printer. This consists of the following procedures, which should be performed in the order presented.
Installation and Setup Unpacking the Printer Electric Shock Caution • Limit AC power supplied to the P430i Printer to 100 – 230 volts, 60 ~ 50 Hertz. Limit excess current draw to 16 amps or less, using an associated circuit breaker or other such device. Never operate the printer in a location where operator, computer, or printer can get wet. Personal injury could result.
Installation and Setup Unpacking the Printer 5. Lift the printer out of the carton by holding it with both hands. 6. Please ensure that you have a clean and nearly dust free environment for proper operation and storage of the printer. 7. Make sure the following items are included with your P430i printer: 980470-001 Rev.
Installation and Setup Unpacking the Printer Card Cleaning Cartridge CD-ROM with Driver Wizard and User’s Manual Power Cables (2) USB Cable Cleaning Kit If any items are missing, please contact your dealer. To reorder, please refer to Appendix D of this manual. 8. Remove packing tape securing the printer’s Main Cover and Card Feeder Cover. 9.
Installation and Setup Unpacking the Printer b. Locate the Print Head protection pad and the Card Cleaning Cartridge location tape (see below). Remove the tape. Remove me I Print Head P rotection Pad c. L A NST L Card Cleaning Cartridge Location Tape Release the Print Head Carriage by pushing the Print Head Carriage Latch to the left, and raise the Print Head Carriage. It will remain open at about a 45° angle. Print Head Carriage Latch Color Sided Dual- 980470-001 Rev.
Installation and Setup Installing the Print Driver Software and Setting Driver Options d. Remove the print head protection pad. Keep the pad, as well as the other packing material and the shipping carton, in case the printer is shipped or moved. If the original material is lost, a replacement Shipping Kit can be ordered from your reseller.
Installation and Setup Loading a Ribbon • Delete previous versions of the driver and clean up any necessary Registry entries. You must select “Remove” from the install options to remove any previous driver versions. Loading a Ribbon i Series Printers require the use of i Series ribbons for full color printing. The Resin Thermal Transfer and Dye Sublimination ribbons for P430i are specifically designed for your P430i Printer. 1. Place the printer power switch in the OFF (0) position. 2.
Installation and Setup Loading a Ribbon Color Sided Dual- Ribbon Take-up Spindle Ribbon Supply Spindle 3. Locate the Ribbon Supply Spindle and the Ribbon Take-up Spindle (see above). Load ribbon onto the supply spindle (under the print head carriage) flange side in, and load the empty core (with tape attached) onto the take-up spindle. Make sure the ribbon comes off the top of the supply spindle and feeds to the top of the take-up spindle.
Installation and Setup Loading a Ribbon Caution • Do not touch the print head if the printer has been in service within the last 10 minutes. It could be very hot and cause a burn. Electrostatic Discharge Caution • A static discharge is possible if you touch any exposed metal parts. Use of an anti-static wrist strap or comparable anti-static protection is required. 4. Gently press the print head carriage down until it is fully lowered, as shown below. Very little force is neccessary to perform this step.
Installation and Setup Installing the Card Cleaning Cartridge Installing the Card Cleaning Cartridge The Card Cleaning Cartridge cleans the cards entering the printer. The Card Cleaning Cartridge consists of a Cartridge Frame and an Adhesive Roller, which are packed together. 1. Remove the Cartridge Frame and the Adhesive Roller from their packaging. Insert the Adhesive Roller into the Cartridge Frame, as shown below. To avoid contamination, always hold the frame and the roller by the ends. . 2.
Installation and Setup Installing the Card Cleaning Cartridge 4. Locate the slot at the rear of the Card Cleaning Cartridge mounting location; see below. Card Cleaning Dual-Sid ed Colo r 5. Hold the Card Cleaning Cartridge by the extended “handle” (so the large arrow on the top is pointing away from you). With the cartridge at about a 30° angle (pointing downward), insert the lip of the cartridge into the slot, until the cartridge seats against the back wall.
Installation and Setup Setting the Card Thickness Control Setting the Card Thickness Control The Card Thickness Control is set by the user to adjust the gap as cards enter the printer, to prevent double-feeds (which could cause a jam) or mis-feeds. Note • Set the Card Thickness Control before loading cards. 1. Open the Card Feeder cover. The cover is hinged; lift it by the lip at the right front corner.
Installation and Setup Setting the Card Thickness Control 3. There are four detents to set the position of the Card Thickness Control. Slide the Card Thickness Control to the position corresponding to the following: Detent Position Card Thickness Highest 50 mil (1.27 mm) to 60 mil (1.52 mm) 3rd position 30 mil (0.76 mm) to 50 mil (1.27 mm) 2nd position 20 mil (0.51 mm) to 40 mil (1.02 mm) Lowest 10 mil (0.25 mm) to 20 mil (0.
Installation and Setup Loading Cards Loading Cards This section shows how to load plastic cards into the P430i Printer. The P430i can use cards with a range of thickness from 10 mil (0.25 mm) to 60 mil (1.5 mm). Note • Do not mix cards of different thicknesses! The P430i Printer can also load and print cards fed individually. Information on this is given in the next chapter. Note • DO NOT bend cards or touch print surfaces as this can reduce print quality.
Installation and Setup Loading Cards 2. Remove all wrapping from the card deck. 3. Holding the card deck by the sides, hold it vertically against a flat surface such as a desktop. If the deck is too thick for your hand to hold it comfortably, use about half a deck at a time. 4. Push the stack back and forth to an angle of about 45° from vertical, so as to separate all of the cards.
Installation and Setup Card Output Hopper Card Output Hopper The card output hopper is normally extended to receive the printed cards. The printer may be operated with the card output hopper in its closed position; in this case the cards will not be collected in the output hopper. 1. Pull the card output hopper out to place it in its functional position. Note • The output hopper is a very snug fit to prevent it from moving during shipping or operation; firm force is required to change its position.
Installation and Setup Connecting the Printer to your Computer Connecting the Printer to your Computer The P430i Printer includes a standard USB interface. As an option, the printer can be ordered with a 10/100base-T Ethernet Adapter (in addition to the USB interface). The Ethernet Adapter can also be ordered as an add-on option and installed in the field by a Zebra factory certified technician. 1.
Installation and Setup Connecting Power Connecting Power The P430i Printer includes an internal AC power supply that accepts nominal input voltage in the range from 110 to 230 volts at 50 to 60 Hertz. The power source must be grounded. Depending on specific model number, your P430i Printer will include one or two power cords; use the one that is appropriate for the AC power source connection at your location.
Installation and Setup Printing a Test Card Printing a Test Card With ribbon and cards loaded, your P430i Printer is ready to print. To check the operation of the printer, you should print a test card. (Printing a test card does not require that the printer be connected to your computer or network, but power must be applied.) 1. Set the printer’s power switch (on the back of the printer) to the OFF ( O ) position. 2.
Installation and Setup Packing the P430i Printer for Shipment 2. If the printer still has power applied and is turned on, and is still connected to the host computer, set the printer’s power switch (on the back of the printer) to the OFF ( O ) position, and disconnect the interface and power cables to the printer. 3. Open the Main Lid. Open the Print Head Carriage and remove the Ribbon. (If you wish to save the ribbon for future use, you may want to put it in a plastic bag for storage.) 4.
3 Printing a Card Printing with the P430i Card Printer is similar to printing with any other printer in a Windows environment. • The Printer Driver Software is installed on your computer (see Chapter 2). • The P430i Printer is connected to the power source and the computer (see Chapter 2). • The P430i Printer is selected by either the Operating System or the appropriate application software program. • Printer Properties are set (the factory default values will be appropriate for many applications).
Printing a Card Printing a Sample Card “Single Feed Options” allows Disabling or Enabling Single Feed Support. • If “Disable Single Feed Support” is selected, when the P430i Card Printer runs out of cards in the feeder, the LCD display will read OUT OF CARDS. To continue, press the panel button.
Printing a Card Removing Rejected Cards 10. The printer will feed in a card and start printing (the data download time will vary depending on the complexity of the card design and the processing speed of your computer). 11. Once the printing job is complete, the card is ejected from the printer into the Output Hopper. Removing Rejected Cards While encoding either magnetic stripe cards or smart cards, if a card fails encoding it is directed to the reject bin.
Printing a Card Feeding One Card at a Time Feeding One Card at a Time A Manual Feed Slot is available below the Card Input Hopper for feeding single cards. The Card Input Hopper must be empty for single-card feeding to work properly. 1. Open the Card Feeder cover. Verify that there are no cards in the feeder, then close the Card Feeder cover. 2. Insert a single card into the slot below the Card Feeder. Do not feed more than one card at a time.
4 Cleaning Caution • PROTECT YOUR FACTORY WARRANTY! The recommended cleaning procedures must be performed to maintain your factory warranty. Other than the recommended cleaning procedures described in this manual, allow only Zebra authorized technicians to service the P430i Printer. NEVER loosen, tighten, adjust, bend, etc., any part or cable inside the printer. NEVER use a high pressure air compressor to remove particles in the printer.
Cleaning Cleaning the Printer How to Clean Note • This cleaning procedure uses two cleaning cards. One cleaning card is the size of a regular plastic card, and is referred to as the “cleaning card.” The other is elongated, with a wider section at one end; it is referred to as the “long cleaning card.” 1. Leave the Printer power on, or turn it on if it was off. 2.
Cleaning Cleaning the Print Head 10. Discard both cleaning cards after a single use. Note • Do not use previously used cleaning cards. Cleaning the Print Head A cleaning using the Cleaning Cards usually suffices. However, a separate Print Head cleaning can remove more stubborn deposits when print anomalies persist. To avoid deposits, only use foam-tipped swabs. 1. Place the printer power switch in the OFF ( O ) position. 2. Open the Main Cover, release the Print Head Carriage, and remove the ribbon.
Cleaning Card Cleaning Cartridge Card Cleaning Cartridge Your P430i Printer includes a Card Cleaning Cartridge. This item cleans the cards entering the printer through the card feeder. To ensure print quality, the cleaning roller requires periodic replacement. New cleaning rollers are included with each ribbon or may be purchased separately. (To reorder, please refer to the Media List on the Windows Drivers and User Documentation CD supplied with this printer.
Cleaning Card Cleaning Cartridge ided Dual-S or Col 3. Remove the cleaning roller from the Card Cleaning Cartridge and discard. 4. Install new cleaning roller into the Card Cleaning Cartridge. To avoid contamination, always hold the cleaning roller by the ends. (For replacement cleaning rollers, please refer to the Media List on the Windows Drivers and User Documentation CD supplied with this printer.) 5. Peel protective wrapper from the cleaning roller by gently pulling on the tape. 980470-001 Rev.
Cleaning Card Cleaning Cartridge Note • DO NOT touch the adhesive roller surface that contacts the cards. 6. Replace the Card Cleaning Cartridge into the printer. For detailed instructions, see Installing the Card Cleaning Cartridge on page 14. Color Sided Dual- Card Cleaning Cartridge in final position 7. Close the printer Main Lid. 34 P430i User’s Manual 980470-001 Rev.
5 Troubleshooting The table on the next page offers causes and solutions to symptoms related to improper operation. Check the table when experiencing any loss of operation or print quality. 980470-001 Rev.
Troubleshooting 36 Problem / Description Cause / Solution The LCD Panel displays OUT OF CARDS message. 1. Check for cards in the card feeder. If no cards present, load cards. 2. Check that Card Thickness Control lever is properly adjusted (see Loading Cards in Chapter 2). 3. Press the Panel Button for 1 second. The printing job will restart. The LCD Panel displays OUT OF RIBBON message. 1. Check ribbon. Replace if defective or entirely used.
Troubleshooting Print Quality Issues Print Quality Issues This section will help you resolve print quality problems. The print quality is dependent on several factors. The two most important factors that will increase your print quality are cleanliness and card stock. To diagnose and fix print quality problems, follow the troubleshooting procedures below: Example 1 • Small spots appear on the printed card with a non-printed area or a different color. Possible Cause: • Contamination on the card surface.
Troubleshooting Print Quality Issues Possible Cause: • Print Head is dirty. Solution: • Clean the Print Head Possible Cause: • Print Head elements are damaged (e.g., scratched or burnt). Solution: • Call Zebra Customer Service for Print Head replacement information. Example 3 • Printing shows very pale, very dark, or inconsistent results Possible Cause: • Ribbon has been stored improperly or is damaged. Solution: • Change ribbon and print again. Possible Cause: • Cards may not meet specifications.
Troubleshooting Print Quality Issues Possible Cause: • Dust or embedded contamination on elements of the Print Head. Solution: • Perform a Cleaning of the Print Head (see Chapter 4). Example 4 • Printing shows blurry printed image. Possible Cause: • Ribbon cartridge may not be correctly positioned. Solution: • Check that the ribbon is properly rolled onto the ribbon cores of the cartridge. • Replace ribbon cartridge, making sure it locks in place, and print again.
Troubleshooting Print Quality Issues Example 5 • No printing on the card. Possible Cause • Ribbon may not be installed in the printer. Solution: • Check for ribbon in the printer. Possible Cause • Cards may not meet specifications. Solution: • Use a different supply of cards. Possible Cause • Print Head elements may be scratched or burnt. Solution • Call Service for Print Head replacement information. Example 6 • Only one panel of a color ribbon prints. Possible Cause • Using the wrong type of ribbon.
Troubleshooting Troubleshooting the Ethernet Connection and Adapter Troubleshooting the Ethernet Connection and Adapter Resetting to Factory Defaults To reset the Ethernet Adapter configuration parameters to the factory defaults, press the Panel Button and hold it in while turning the printer power on. Keep the Panel Button pressed until the Status Indicator light turns green, then release the Panel Button. To print a configuration card, press and hold the Ethernet switch.
Troubleshooting Troubleshooting the Ethernet Connection and Adapter Network Status/Activity Indicator A bi-color Status/Activity LED indicates network speed, established link, and network activity. 1. If the LED is off, no link was established. 2. If the LED is solid green, a 100Base link is established. 3. If the LED is flashing green, a 100Base link is established and network activity has been detected. 4. If the LED is solid orange, a 10Base link is established. 5.
6 Technical Specifications General Specifications • • Full color dye-sublimation or monochrome thermal transfer card printing 102 cards per hour (31.8 seconds per card) double-sided printing, YMCKO front, K back Ribbon Specifications • • Patented ribbon core and spindle system i Series technology featuring RFID Note • "i Series" Printers require the use of "i Series" ribbons for full color printing. For more information about Card Media and Ribbons available from Zebra Technologies Corp.
Technical Specifications Card Specifications Card Specifications • • • • • • • Types: PVC or Composite Card Width/length ISO CR-80 - ISO 7810, 2.125" (54 mm) x 3.375" (86 mm) Option: Magnetic Stripe - ISO 7811 Card thickness: 10-60 mil (0.25-1.
Technical Specifications Bi-Directional Communications Interfaces ISO Standard 7811 Dimensions for Magnetic Stripe Card Contact Location for Smart Card ISO Standard 7816 0.757 in (19.23 mm) 1.124 in (28.55 mm) 0.403 in (10.25 mm) 0.782 in (19.87 mm) ISO 7816 Cards Bi-Directional Communications Interfaces • • USB Built-in Ethernet (optional) Mechanical Specifications • • • • Width: 26 in (661 mm) Depth: 10 in (254 mm) Height: 11 in (279 mm); 12 in (305 mm) with extended feeder Weight: 20 lbs (9.
Technical Specifications Environmental Environmental • • • • • Operating Temperature: 59°F to 85°F (15°C to 35°C) Operating Humidity: 20% to 65% non condensing Storage Temperature: 23°F to 158°F (-5°C to 70°C) Storage Humidity: 20% to 70% non-condensing Ventilation: Reasonably dust free air environment Options • • • • • 46 Built-in 10/100 Mbps Ethernet network communications Three track magnetic stripe encoder (standard and reverse) High capacity feeder (220 30-mil cards) Contactless encoding (MIFARE a
APPENDIX A Magnetic Card Stripe Encoder Introduction This Appendix includes operation and maintenance requirements for the P430i Printer with the optional magnetic card stripe encoder. (See Chapter 2 for location of the Magnetic Card Stripe Encoder.) The magnetic encoder can be set for either high or low coercivity. Use the printer driver to change the encoder setting. Media Loading Orientation The magnetic encoder may be installed with the read/write head positioned below the card path.
Magnetic Card Stripe Encoder Sample Encoding Program Sample Encoding Program Refer to the Programmer’s Manual (document number 980415). Note • ONLY USE cards that comply with ISO 7810 and 7811 standards for magnetic stripe cards. The magnetic stripe must be flush to the surface of the card to work properly. Never use cards which have taped-on magnetic stripes. Magnetic Encoder Cleaning The Magnetic Encoder Read/Write Head is cleaned as part of the printer cleaning process.
Magnetic Card Stripe Encoder ISO Standard Encoding ISO Standard Encoding Field Separator Track # Track Density Valid Characters # of characters 1 ^ 210 BPI* Alphanumeric (ASCII 20~95†) 79‡ 2 = 75 BPI* Numeric (ASCII 48~62) 40‡ 3 = 210 BPI* Numeric (ASCII 48~62) 107‡ *Bits per inch †Except the “?” character ‡Including Start, Stop, and LRC characters. Also note that these 3 characters are automatically managed by the magnetic encoder according to the ISO Standard Norms.
Magnetic Card Stripe Encoder ISO Standard Encoding Color Sided Dual- 50 P430i User’s Manual 980470-001 Rev.
APPENDIX B Smart Card Contact Station This section contains information on the additional operations of a P430i Printer equipped with the optional Smart Card Contact Station. (See Chapter 2 for location.) Introduction Smart Cards can have a built-in microcomputer and/or memory to store fingerprints, voice recognition patterns, medical records, and other such data. The P430i Printer may be equipped with an optional contact station for programming Smart Cards (ISO 7816).
Smart Card Contact Station Smart Card Contact Station Interface Smart Card Contact Station Interface When a command to the printer interface sends a card to the Smart Card Contact Station, the printer connects the Smart Card Contact Station to the female DB-9 connector on the rear of the printer. DB-9 Connector location for Smart Card Contact Station An attached external Smart Card Programmer can be used to program Smart Card chips. The following table shows the Smart Card Contact Points.
APPENDIX C Connecting to a Network Card printers can be connected to an Ethernet network in three ways. Printer Sharing In printer sharing, the printer is connected locally to the host computer and configured to be shared to other client computers. Client computers connect to the printer over the network through the host computer. 980470-001 Rev.
Connecting to a Network External Print Server External Print Server A stand alone device that acts as a server on the network specifically for receiving print jobs and passing them to the printer. Client computers connect to the print server over a network. Internal Print Server Similar to an external print server, except the print server is integrated into the printer. This removes the need for a separate power supply and separate device drivers. This is the simplest way to network a printer.
APPENDIX D Worldwide Sales & Support Sales and Support Locations Zebra Technologies Card Printer Solutions 1001 Flynn Road Camarillo, CA 93012-8706 USA Phone: + 1 (805) 579 1800 Fax: + 1 (805) 579 1808 Toll free in US: (800) 452-4056 e-mail: cards@zebra.com Zebra Technologies Card Printer Solutions, Europe, Middle East, Africa The Valley Centre, Gordon Road, High Wycombe Buckinghamshire HP13 6EQ, England Phone: + 44 (0) 870 241 1527 Fax: + 44 (0) 870 241 0765 e-mail: eurosales@zebra.
Worldwide Sales & Support Corporate Headquarters Zebra Technologies Card Printer Solutions, Asia/Pacifique 1 Sims Lane # 06-11 387355 Singapore Phone: + 65 84 20 322 Fax: + 65 84 20 514 e-mail: asiasales@zebra.com Corporate Headquarters Zebra Technologies Corporation 333 Corporate Woods Parkway Vernon Hills, IL 60061-3109 USA Phone: + 1 (847) 634 6700 Fax: + 1 (847) 913 8766 e-mail: sales@zebra.com Website www.zebracard.com 56 P430i User’s Manual 980470-001 Rev.
