6001352_UG_EN_030315.
We hope you enjoy your Zeraxa Drone with Camera from RadioShack. Please read this user’s guide before setting up and using your drone. CHOKING HAZARD! Small parts. Not for children under 3 years. Package Contents •• Zeraxa Drone with Camera •• USB Charging Cable •• 3.7V Drone Battery • Remote Control • Spare Blades (2) • User’s Guide Install Batteries in the Remote Control 1. On the remote control, set the ON/OFF/Special switch to OFF. 2. Use a screwdriver to open the battery compartment. 3.
Charge the Drone Battery Your drone uses a lithium polymer battery for power. 1. Use a screwdriver to open the drone battery compartment door. 2. Take out the battery. Holding the battery connector (NOT the cable), carefully unplug the battery from the drone. 3. Use the USB charging cable to connect the battery to a USB power source, such as a laptop. The LED on the USB connector lights red during charging, and turns off when charging is complete. A full charge takes about 100 minutes.
Rotor Blades (4) ON/OFF Body LEDs (red) Back LEDs (green) Front LEDs (white) Camera Lens 6 6001352_UG_EN_030315.
LED Throttle Steering Ascend Turn left Forward Turn right Slide left Descend Slide right Backward Left/Right Turning Trim Left/Right Slide Trim ON/OFF/Special Forward/Reverse Movement Trim FLIP Turn stunt mode on/off. . HI/LO Switch between high speed (double beep) and low speed (single beep). Photo 8 6001352_UG_EN_030315.
Get Ready to Fly Fly Your Drone 1. Plug the drone battery into the socket, insert the battery and its cable into the battery compartment, and secure the compartment door. Screw 1. With the drone on the ground, move the throttle forward to fly. 2. To land your drone, slowly move the throttle backward to descend. Avoid moving the throttle too quickly, as it can stop the blades instantly and cause the drone to crash. 3. When you finish flying the drone, turn off the remote control and drone.
Calibrate When flying in a new location, or when controlling the drone becomes difficult, use the following steps to calibrate the compass. Regular calibration keeps the compass finely tuned. 1. Select an open location without strong magnetic interference and place the drone and remote control on level ground. 2. Turn on the drone and switch the remote control to Special. Then pair the remote control with the drone. 3. Calibrate the drone: a.
Use the Detachable Camera Replace Damaged Blades The red LED inside the camera flashes when connected to the drone and the drone is turned on. Video Photo The left and right blades of the drone are different (see R/L orientation marking on underside); you must use the correct blade in the correct location. If you need additional blades, visit your local RadioShack store for help. To replace a damaged blade, remove the old one and press the new one onto the blade axle.
FCC Information Limited Warranty This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE AND ANY LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT AND ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RADIOSHACK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
Complies with the European Union’s “Restriction of Hazardous Substances Directive,” which protects the environment by restricting specific hazardous materials and products. © 2015 RadioShack Corporation. All rights reserved. RadioShack is a registered trademark used by RadioShack Corporation. 6001352_UG_EN_030315.
