User's Manual

ManualsBrandsZEGO ELECTRONIC ManualsDronesController of Vektor Drone

04A15

6001357, 6001376

Printed

in China

Vektor Drone

Install Batteries in the Remote

Control

On the remote control, set the ON/OFF switch to OFF.

Use a screwdriver to open the battery compartment.

Insert two AAA batteries (not included), matching

the polarities (+ and –) marked inside. Use alkaline

batteries for optimal performance. Replace the cover.

Note: If the remote control’s LED ashes during use, the

batteries are low and should be replaced.

Age 12+

Get Ready to Fly

1. Turn on the drone. The LED ashes green.

2. Place the drone on level ground.

Turn on the remote control. The remote control's LED ashes.

Move the throttle all the way up and then down to pair the remote control with the drone.

The drone’s blades remain still during pairing. When paired, the LEDs on both the remote

control and drone light steadily.

Note:

If pairing fails, turn o the drone and remote control and repeat the steps above, or change

locations to avoid electrical interference.

Fly Your Drone

1. After pairing, push the steering control in to switch between high speed (double beep) and low

speed (single beep).

2. With the drone on the ground, move the throttle forward to ascend. To avoid ground air

turbulence, y the drone at least 1 ft. (30cm) o the ground.

For advanced users: Hold the remote control with one hand, resting your thumb on the throttle.

Throw the drone about 9 ft. (3m) away from you, and move the throttle forward to y. The drone

adjusts itself automatically and ies smoothly.

IMPORTANT: If your drone crashes upside down, pull the throttle down and switch o the remote

control rst. Never touch the drone when blades are still moving.

We hope you enjoy your Vektor Drone from

RadioShack. Please read this user’s guide before

setting up and using your drone.

What’s Included

• Vektor Drone • Remote Control

• USB Charging Cable • Spare Blades (4)

• 3.7V Drone Battery • User’s Guide

Charge the Drone

Your drone uses a built-in lithium polymer battery for power.

Use the USB charging cable to connect the battery to a USB power

source (such as a laptop). The LED on the USB connector lights red

during charging, and turns o when charging is complete.

A full charge takes about 35 minutes. A fully charged battery

provides up to 4 minutes of ight time.

2. After charging, unplug the USB charging cable. Do not attempt to

overcharge the battery.

Caution: Use only the included USB charging cable to charge the

drone's battery. Using any other cable may damage the drone.

LED ON/OFF

LED

Arrow

side up

LED

Rotor Blades (4)

Left/Right Slide Trim

Forward/Reverse Movement Trim

Throttle Steering

Forward

Ascend

Backward

Descend

Slide rightTurn right Slide leftTurn left

Push

(Stunt mode)

Push

(High/low

speed)

ON/OFF

6001357, 6001376_UG_EN.indd 1 4/29/2015 2:23:36 PM

Summary of content (2 pages)

PAGE 1
BC Vektor Drone We hope you enjoy your Vektor Drone from RadioShack. Please read this user’s guide before setting up and using your drone. What’s Included Age 12+ Rotor Blades (4) • Vektor Drone • Remote Control • USB Charging Cable • Spare Blades (4) • 3.
PAGE 2
Trim Your Drone Perform Stunts Calibrate the Drone Replace Damaged Blades Move the throttle forward and see how the drone reacts. 1. Push the throttle control in so that the remote control beeps repeatedly, indicating the drone is in stunt mode. If controlling the drone becomes difficult, use the following steps to calibrate the drone. The left and right blades of the drone are different (see A and B markings on the drone and blades).