www.zektor.com 858•748•8250 Poway, CA 92064 Suite 401 12675 Danielson Ct ZEKTOR Z E K T O R Rev 2 ZEK T OR 2 3 4 High Definition Component Video Switch 1 HDS4.
ii Contents What’s Inside ..................................... 1 An Overview of the HDS4.1 ................ 3 Easy, Simple, Instructions! ................. 5 Three Simple Steps to a Remote! ........ 7 Controlling the Front Panel Lights ..... 9 Adjusting the Front Panel Intensity .. 11 Setting the Initial Power On State .... 13 Disabling Front Panel or Remote ...... 15 Resetting to Factory Defaults ........... 17 Specifications .................................. 19 Warranty Policy .........................
20 HDS4.1 Component Video Switch Shipment of produc t is as adver tised by produc t. Upon receipt of merchandise inspec t produc t carefully, should you find that the produc t does not meet your expec tations, or satisfac tion, contac t us at once and tell us your concerns, so we may make ever y effor t to satisfy your purchase.
2 R/V Pb/B L/H ZEKTOR 1 Y/G C/V Pr/R 2 R/V Y/G L/H Pb/B C/V Pr/R 3 R/V Y/G 1 L/H Pb/B 4 R/V Y/G L/H Pb/B C/V Pr/R 3 OUT R/V Pb/B L/H Pr/R C/V 4 1 OUT 2 OUT 3 4 Y/G Rear Panel 2 Front Panel C/V Pr/R HDS4.1 Component Video Switch 1 3 DIGITAL AUDIO 2 4 OUT 9VDC 1 2 3 4 5 6 1 2 3 4 5 Specifications: Analog Channels Bandwidth @ -0.
18 HDS4.1 Component Video Switch Power I ndicator. Lights up in standby mode. S elec tion LEDs. I ndicate currently selec ted inputs. I nput S elec tion Buttons. I nfrared Remote S ensor Window. I nfrared Received I ndicator. Flashes when IR is received. Power Toggle Button. 5. 4. 2. 3. 1. HDS4.1 Component Video Switch Analog I nputs. Each input consists of six equivalent channels.
4 R/V L/H Pb/B C/V Pr/R 2 R/V Y/G L/H Pb/B C/V Pr/R 3 R/V Y/G To DVD L/H Pb/B C/V Pr/R 4 R/V Y/G L/H Pb/B Unused Input To Game Console 2 C/V Pr/R OUT 3 L/H Pr/R C/V 4 1 OUT 2 OUT 3 To Composite Monitor w/Analog Audio R/V Pb/B To Projector or Monitor 1 2 9 6 3 3 4 DIGITAL AUDIO 3 4 OUT To Home Theater Receiver’s Digital Audio Input 9VDC To Power Module Turn to the next chapter for simple instructions on how to setup the HDS4.
Start by pressing and holding the Power button... 3 1 16 HDS4.1 Component Video Switch 1 ZE KT O R 4 ...while continuing to hold the Power button, press and hold both the ‘2’ and the ‘3’ buttons. 3 After about 4 seconds, the display will flash indicating all parameters have been restored to their factory programmed values. 2 2 Step 1: Reset All Parameters to Factory Defaults Use nearly any remote to control your HDS4.1! Using any remote to operate the HDS4.
6 1 2 3 4 Step 1: Put the HDS4.1 into the Setup Mode ZEKTOR Press and hold the Power Button for 4 secs. The standby LED will blink wildly, and the selection LEDs will start sequencing to the right. (You’ll know it when it happens!) 1 2 2 9 6 3 2 3 4 That’s it! The HDS4.1 now operates with your new remote control! Power 1 2 3 4 8 9 Press the following sequence of buttons on your remote control: 4 ...the standby LED will flash slower, and all the other LEDs will turn off.
Start by pressing and holding the Power button... 1 3 4 ...while continuing to hold the Power button, press and hold the ‘4’ button. 3 After about 4 seconds, the standby LED will flash quickly, and the display will indicate the current enable / disable statuses. 2 2 1 14 HDS4.
8 1 2 3 4 Step 1: Place the HDS4.1 into the Setup Mode ZEKTOR 2 2 3 3 4 4 Exit Setup Mode Auto-Fade Always Bright Always Dim Always Off Press and hold the Power Button for 4 secs. The standby LED will blink wildly, and the selection LEDs will start sequencing to the right. 1 Step 2: Select “Lighting Mode” option ZEKTOR After ‘3’ is pressed, the standby LED continues to flash, and the front panel will display the current Light Mode setting. 1 Step 3: Choose a new lighting mode ZEKTOR HDS4.
1 2 3 Start by pressing and holding the Power button... 1 12 HDS4.1 Component Video Switch 1 ZE KT O R 3 4 ...while continuing to hold the Power button, press and hold the ‘1’ button. 3 4 After about 4 seconds, the display will flash indicating the new power on state has been accepted. 2 2 Step 2: Save the new initial power on state Setup the HDS4.1 to the initial power on state you’d prefer. Z EKTOR Step 1: Set the HDS4.
1 2 3 4 Step 1: Place the HDS4.1 into the Setup Mode ZEKTOR 2 2 3 3 4 4 Exit Setup Mode Press to Brighten LEDs Press to Dim LEDs Selects BRIGHT level Selects DIM level Press and hold the Power Button for 4 secs. The standby LED will blink wildly, and the selection LEDs will start sequencing to the right. 1 Step 2: Select “Front Panel Intensity” option ZEKTOR After ‘4’ is pressed, the standby LED continues to flash, and the front panel will display the current intensity setting.